Nicolas Vanderesse, Philippe Bocher, Natalia Nuño, Alejandro Yánez, Lucas A. Hof.
2022.
« On the characterization of roughness and geometrical irregularities of additively manufactured single titanium-alloy struts ».
Additive Manufacturing.
vol. 54
E. J. Herrera-Jimenez, N. Vanderesse, E. Bousser, T. Schmitt, P. Bocher, L. Martinu, J. E. Klemberg-Sapieha.
2021.
« Fracture mechanism of TiN coatings on Ti-6Al-4V substrates : Role of interfaces and of the residual stress depth profile ».
Surface and Coatings Technology.
vol. 426
12 p.
Y. Zedan, M. Iben Houria, N. Vanderesse, F. Atmani, F. Mirakhorli, F. Nadeau, V. Demers, P. Bocher.
2021.
« Fatigue properties of continuous wave and pulsed wave laser cold-wire welding of thick section AA6005-T6 aluminum alloys ».
International Journal of Fatigue.
vol. 147
13 p.
Mahdi Masoumi Khalilabad, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher.
2021.
« Effect of heat treatments on microstructural and mechanical characteristics of dissimilar friction stir welded 2198/2024 aluminum alloys ».
Journal of Adhesion Science and Technology.
19 p.
(In press)
Pierre Maurel, Laurent Weiss, Philippe Bocher, Thierry Grosdidier.
2021.
« Effects of SMAT at cryogenic and room temperatures on the kink band and martensite formations with associated fatigue resistance in a β-metastable titanium alloy ».
Materials Science and Engineering A.
vol. 803
11 p.
Samuel Milton, Olivier Rigo, Sebastien LeCorre, Antoine Morandeau, Raveendra Siriki, Philippe Bocher, Rene Leroy.
2021.
« Microstructure effects on the machinability behaviour of Ti6Al4V produced by Selective Laser Melting and Electron Beam Melting process ».
Materials Science and Engineering A.
vol. 823
12 p.
Fayaz Foroozmehr, Philippe Bocher.
2021.
« An investigation on fracture toughness of the heat-affected zone in the welded joints of 13% Cr-4% Ni martensitic stainless steels ».
Fatigue & Fracture of Engineering Materials & Structures.
(In press)
Thomas Perard, Alexey Sova, Hugo Robe, Vincent Robin, Yasser Zedan, Philippe Bocher, Eric Feulvarch.
2021.
« Friction stir processing of austenitic stainless steel cold spray coating deposited on 304L stainless steel substrate: Feasibility study ».
International Journal of Advanced Manufacturing Technology.
vol. 115 , nº 7-8.
p. 2379-2393.
Stéphane Godin, Johann Hamel-Akré, Denis Thibault, Alessandra-Maria Serventi, Philippe Bocher.
2020.
« Ni and Mn enrichment effects on reformed austenite: thermodynamical and low cycle fatigue stability of 13%Cr–4%Ni and 13%Cr–6%Ni stainless steels ».
SN Applied Sciences.
vol. 2 , nº 3.
J. Ajaja, W. Jomaa, P. Bocher, R. R. Chromik, M. Brochu.
2020.
« High cycle fatigue behavior of hard turned 300 M ultra-high strength steel ».
International Journal of Fatigue.
vol. 131
N. Vanderesse, D. Texier, P. Bocher.
2020.
« Effect of porosities on brazed martensitic steel tensile properties: 2D and 3D pre-mortem vs post-mortem characterizations ».
Materials Characterization.
vol. 160
14 p.
Mahdi Jamshidinia, Hadi Ghasemi-Nanesa, Philippe Bocher, Natalia Nuno, Behrang Poorganji, Mahdi Habibnejad-Korayem.
2020.
« Microstructural alteration of alloyed steel in direct metal laser melting by powder bed deposition system ».
Steel Research International.
vol. 91 , nº 10.
7 p.
Amrita Bag, Dorian Delbergue, Jihane Ajaja, Philippe Bocher, Martin Lévesque, Myriam Brochu.
2020.
« Effect of different shot peening conditions on the fatigue life of 300M steel submitted to high stress amplitudes ».
International Journal of Fatigue.
vol. 130
12 p.
R. Bretin, M. Levesque, P. Pilvin, P. Bocher.
2020.
« Neighborhood effect within polycrystalline materials: Elastoplastic micromechanical analysis by cellular automaton and finite element ».
International Journal of Fatigue.
vol. 137
16 p.
Kanwal Chadha, Yuan Tian, Philippe Bocher, John G. Spray, Clodualdo Aranas.
2020.
« Microstructure evolution, mechanical properties and deformation behavior of an additively manufactured maraging steel ».
Materials.
vol. 13 , nº 10.
16 p.
Pierre Maurel, Laurent Weiss, Thierry Grosdidier, Philippe Bocher.
2020.
« How does surface integrity of nanostructured surfaces induced by severe plastic deformation influence fatigue behaviors of Al alloys with enhanced precipitation? ».
International Journal of Fatigue.
vol. 140
12 p.
Clément Dureau, Marc Novelli, Mandana Arzaghi, Roxane Massion, Philippe Bocher, Yves Nadot, Thierry Grosdidier.
2020.
« On the influence of ultrasonic surface mechanical attrition treatment (SMAT) on the fatigue behavior of the 304L austenitic stainless steel ».
Metals.
vol. 10 , nº 1.
14 p.
Fayaz Foroozmehr, Philippe Bocher.
2020.
« Effect of low temperature intercritical heat-treatment on stable crack growth behavior in 13% Cr-4% Ni martensitic stainless steel multipass weldments ».
Engineering Fracture Mechanics.
vol. 240
Fayaz Foroozmehr, Philippe Bocher.
2020.
« On the ductile rupture of 13% Cr-4% Ni martensitic stainless steels ».
International Journal of Fracture.
vol. 224 , nº 1.
p. 67-82.
Yousef Saadati, Jean-François Chatelain, Gilbert Lebrun, Yves Beauchamp, Philippe Bocher, Nicolas Vanderesse.
2020.
« A study of the interlaminar fracture toughness of unidirectional flax/epoxy composites ».
Journal of Composites Science.
vol. 4 , nº 2.
I. Tabiai, D. Texier, P. Bocher, D. Therriault, M. Levesque.
2020.
« In-situ full field out of plane displacement and strain measurements at the micro-scale in single reinforcement composites under transverse load ».
Experimental Mechanics.
vol. 60 , nº 3.
p. 359-377.
Lofti Toubal, Hamed Chaabouni, Philippe Bocher, Chen Jianqiang.
2020.
« Monitoring fracture of high-strength steel under tensile and constant loading using acoustic emission analysis ».
Engineering Failure Analysis.
vol. 108
J. Ajaja, W. Jomaa, P. Bocher, R. R. Chromik, V. Songmene, M. Brochu.
2019.
« Hard turning multi-performance optimization for improving the surface integrity of 300M ultra-high strength steel ».
International Journal of Advanced Manufacturing Technology.
vol. 104 , nº 1-4.
p. 141-157.
Hamid Javadi, Walid Jomaa, Victor Songmene, Myriam Brochu, Philippe Bocher.
2019.
« Inconel 718 superalloy controlled surface integrity for fatigue applications produced by precision turning ».
International Journal of Precision Engineering and Manufacturing.
vol. 20 , nº 8.
p. 1297-1310.
Amrita Bag, Dorian Delbergue, Philippe Bocher, Martin Lévesque, Myriam Brochu.
2019.
« Statistical analysis of high cycle fatigue life and inclusion size distribution in shot peened 300M steel ».
International Journal of Fatigue.
vol. 118
p. 126-138.
Rémi Bertrand, Hugo Robe, Damien Texier, Yasser Zedan, Eric Feulvarch, Philippe Bocher.
2019.
« Analysis of AA2XXX/AA7XXX friction stir welds ».
Journal of Materials Processing Technology.
vol. 271
p. 312-324.
C. Bianchetti, D. Delbergue, Philippe Bocher, M. Levesque, M. Brochu.
2019.
« Analytical fatigue life prediction of shot peened AA 7050-T7451 ».
International Journal of Fatigue.
vol. 118
p. 271-281.
R. Bretin, M. Levesque, P. Bocher.
2019.
« Neighborhood effect on the strain distribution in linearly elastic polycrystals: Part 1 Finite element study of the interaction between grains ».
International Journal of Solids and Structures.
vol. 176-177
p. 36-48.
R. Bretin, M. Levesque, P. Bocher.
2019.
« Neighborhood effect on the strain distribution in linearly elastic polycrystals: Part 2 - Cellular Automaton ».
International Journal of Solids and Structures.
vol. 176-177
p. 49-67.
Mohamed Khalifa, Noureddine Barka, Jean Brousseau, Philippe Bocher.
2019.
« Optimization of the edge effect of 4340 steel specimen heated by induction process with flux concentrators using finite element axis-symmetric simulation and experimental validation ».
International Journal of Advanced Manufacturing Technology.
vol. 104 , nº 9-12.
9 p.
p. 4549-4557.
Mohamed Khalifa, Noureddine Barka, Jean Brousseau, Philippe Bocher.
2019.
« Reduction of edge effect using response surface methodology and artificial neural network modeling of a spur gear treated by induction with flux concentrators ».
International Journal of Advanced Manufacturing Technology.
vol. 104 , nº 1-4.
p. 103-117.
Mohamed Khalifa, Noureddine Barka, Jean Brousseau, Philippe Bocher.
2019.
« Sensitivity study of hardness profile of 4340 steel disc hardened by induction according to machine parameters and geometrical factors ».
International Journal of Advanced Manufacturing Technology.
vol. 101 , nº 1-4.
p. 209-221.
J. H. Liu, N. Vanderesse, J. C. Stinville, T. M. Pollock, P. Bocher, D. Texier.
2019.
« In-plane and out-of-plane deformation at the sub-grain scale in polycrystalline materials assessed by confocal microscopy ».
Acta Materialia.
vol. 169
p. 260-274.
Dorian Delbergue, Damien Texier, Martin Lévesque, Philippe Bocher.
2019.
« Diffracting-grain identification from electron backscatter diffraction maps during residual stress measurements: a comparison between the sin2ψ and cosα methods ».
Journal of Applied Crystallography.
vol. 52 , nº 4.
p. 828-843.
Pierre Maurel, Laurent Weiss, Philippe Bocher, Eric Fleury, Thierry Grosdidier.
2019.
« Oxide dependent wear mechanisms of titanium against a steel counterface: influence of SMAT nanostructured surface ».
Wear.
vol. 430-431
p. 245-255.
G. R. Ebrahimi, A. Momeni, H. R. Ezatpour, M. Jahazi, P. Bocher.
2019.
« Dynamic recrystallization in Mone1400 Ni-Cu alloy: mechanism and role of twinning ».
Materials Science and Engineering : A.
vol. 744
p. 376-385.
Binhan Sun, Yan Ma, Nicolas Vanderesse, Rama Srinivas Varanasi, Wenwen Song, Philippe Bocher, Dirk Ponge, Dierk Raabe.
2019.
« Macroscopic to nanoscopic in situ investigation on yielding mechanisms in ultrafine grained medium Mn steels: role of the austenite-ferrite interface ».
Acta Materialia.
vol. 178
p. 10-25.
Kamel Touahir, Ali Bilek, Philippe Bocher, Mustapha Beldi.
2019.
« Experimental and numerical analysis of the fields of the frozen stresses in an epoxy sphere using the stress-freezing method and mechanical slicing ».
Journal of Materials and Engineering Structures.
vol. 6 , nº 2.
Heithem Touazine, Kanwal Chadha, Mohammad Jahazi, Philippe Bocher.
2019.
« Characterization of subsurface microstructural alterations induced by hard turning of Inconel 718 ».
Journal of Materials Engineering and Performance.
vol. 28 , nº 11.
p. 7016-7024.
Nguyen Hoa Ngan, Philippe Bocher.
2018.
« Finite element analysis simulation of the effect of induction hardening on rolling contact fatigue ».
Journal of Tribology.
vol. 140 , nº 6.
N. Vanderesse, B. Larregain, F. Bridier, P. Bocher.
2018.
« Experimental assessment of high heating rates in induction heating with temperature-sensitive lacquers ».
Journal of Materials Engineering and Performance.
vol. 27 , nº 8.
p. 3831-3843.
N. Vanderesse, A. Richter, N. Nuño, P. Bocher.
2018.
« Measurement of deformation heterogeneities in additive manufactured lattice materials by Digital Image Correlation: Strain maps analysis and reliability assessment ».
Journal of the Mechanical Behavior of Biomedical Materials.
vol. 86
p. 397-408.
Wei Wang, Huaiju Liu, Caichao Zhu, Philippe Bocher, Heli Liu, Zhangdong Sun.
2018.
« Evaluation of rolling contact fatigue of a carburized wind turbine gear considering the residual stress and hardness gradient ».
Journal of Tribology.
vol. 140 , nº 6.
10 p.
T. Klotz, D. Delbergue, P. Bocher, M. Levesque, M. Brochu.
2018.
« Surface characteristics and fatigue behavior of shot peened Inconel 718 ».
International Journal of Fatigue.
vol. 110
p. 10-21.
Jianqiang Chen, Vincent Demers, Daniel P. Turner, Philippe Bocher.
2018.
« Experimental investigation on high-cycle fatigue of inconel 625 superalloy brazed joints ».
Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science.
vol. 49A , nº 4.
p. 1244-1253.
Heli Liu, Huaiju Liu, Philippe Bocher, Caichao Zhu, Zhangdong Sun.
2018.
« Effects of case hardening properties on the contact fatigue of a wind turbine gear pair ».
International Journal of Mechanical Sciences.
vol. 141
p. 520-527.
Mahdi Masoumi Khalilabad, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher.
2018.
« Effect of tool geometry and welding speed on mechanical properties of dissimilar AA2198–AA2024 FSWed joint ».
Journal of Manufacturing Processes.
vol. 34, part A
p. 86-95.
Faranak Nazemi, Johann Hamel-Akré, Philippe Bocher.
2018.
« Modeling of cementite coarsening during tempering of low-alloyed-medium carbon steel ».
Journal of Materials Science.
vol. 53 , nº 8.
p. 6198-6218.
M. Novelli, P. Bocher, T. Grosdidier.
2018.
« Effect of cryogenic temperatures and processing parameters on gradient-structure of a stainless steel treated by ultrasonic surface mechanical attrition treatment ».
Materials Characterization.
vol. 139
p. 197-207.
D. Texier, F. Atmani, P. Bocher, F. Nadeau, J. Chen, Y. Zedan, N. Vanderesse, V. Demers.
2018.
« Fatigue performances of FSW and GMAW aluminum alloys welded joints: Competition between microstructural and structural-contact-fretting crack initiation ».
International Journal of Fatigue.
vol. 116
p. 220-233.
Ehsan Tolouei, Mohammad Reza Toroghinejad, Hamed Asgari, Hossein Monajati Zadeh, Fakhreddin Ashrafizadeh, Jerzy A. Szpunar, Philippe Bocher.
2018.
« Microstructure and texture development in Al-3%Brass composite produced through ARB ».
Advanced Engineering Materials.
vol. 20 , nº 4.
9 p.
Fubin Tu, Dorian Delbergue, Thierry Klotz, Amrita Bag, Hongyan Miao, Charles Bianchetti, Myriam Brochu, Philippe Bocher, Martin Levesque.
2018.
« Discrete element-periodic cell coupling model and investigations on shot stream expansion, Almen intensities and target materials ».
International Journal of Mechanical Sciences.
vol. 145
p. 353-366.
M. Anderson, A. L. Thielin, F. Bridier, P. Bocher, J. Savoie.
2017.
« δ Phase precipitation in Inconel 718 and associated mechanical properties ».
Materials Science and Engineering A.
vol. 679
p. 48-55.
Walid Jomaa, Julie Lévesque, Philippe Bocher, Arnaud Divialle, Augustin Gakwaya.
2017.
« Optimization study of dry peripheral milling process for improving aeronautical part integrity using Grey relational analysis ».
International Journal of Advanced Manufacturing Technology.
vol. 91 , nº 1-4.
12 p.
p. 931-942.
Walid Jomaa, Oussama Mechri, Julie Levesque, Victor Songmene, Philippe Bocher, Augustin Gakwaya.
2017.
« Finite element simulation and analysis of serrated chip formation during highspeed machining of AA7075T651 alloy ».
Journal of Manufacturing Processes.
vol. 26
p. 446-458.
Walid Jomaa, Victor Songmene, Philippe Bocher.
2017.
« Predictive analytical modeling of cutting forces generated by high-speed machining of ductile and hard metals ».
Machining Science and Technology.
vol. 21 , nº 3.
27 p.
p. 335-361.
Jianqiang Chen, Vincent Demers, Eve-Line Cadotte, Daniel Turner, Philippe Bocher.
2017.
« Structural performance of inconel 625 superalloy brazed joints ».
Journal of Materials Engineering and Performance.
vol. 26 , nº 2.
7 p.
p. 547-553.
P. Comot, P. Bocher, P. Belanger.
2017.
« Ultrasonic guided wave inspection of Inconel 625 brazed lap joints: Simulation and experimentation ».
NDT and E International.
vol. 91
p. 71-78.
Kevin McMeekin, Frédéric Sirois, Maxime Tousignant, Philippe Bocher.
2017.
« Improving the accuracy of time-harmonic FE simulations in induction heating applications Towards better ferromagnetic material models ».
COMPEL - The International Journal for Computation and Mathematics in Electrical and Electronic Engineering.
vol. 36 , nº 2.
p. 526-534.
Shilan Meimandi, Nicolas Vanderesse, Denis Thibault, Philippe Bocher, Martin Viens.
2017.
« Macro-defects characterization in cast CA-6NM martensitic stainless steel ».
Materials Characterization.
vol. 124
p. 31-39.
Fayaz Foroozmehr, Yves Verreman, Jianqiang Chen, Denis Thibault, Philippe Bocher.
2017.
« Effect of inclusions on fracture behavior of cast and wrought 13% Cr-4% Ni martensitic stainless steels ».
Engineering Fracture Mechanics.
vol. 175
p. 262-278.
N. Siredey-Schwaller, J. Hamel-Akre, L. Peltier, A. Hazotte, P. Bocher.
2017.
« Solidification sequence of Ni-Si-Cr ~3wt% B brazing alloys ».
Welding in the World.
vol. 61 , nº 6.
p. 1253-1265.
J. C. Stinville, M. P. Echlin, P. G. Callahan, V. M. Miller, D. Texier, F. Bridier, P. Bocher, T. M. Pollock.
2017.
« Measurement of strain localization resulting from monotonic and cyclic loading at 650C in nickel base superalloys ».
Experimental Mechanics.
vol. 57 , nº 8.
p. 1289-1309.
Binhan Sun, Nicolas Vanderesse, Fateh Fazeli, Colin Scott, Jianqiang Chen, Philippe Bocher, Mohammad Jahazi, Stephen Yue.
2017.
« Discontinuous strain-induced martensite transformation related to the Portevin-Le Chatelier effect in a medium manganese steel ».
Scripta Materialia.
vol. 133
p. 9-13.
Heithem Touazine, Jordan Akab, Mohammad Jahazi, Antoine Tahan, Walid Jomaa, Philippe Bocher.
2017.
« Modeling of the microstructure alteration induced by hard turning of Inconel 718 ».
International Journal of Advanced Manufacturing Technology.
vol. 93 , nº 9-12.
8 p.
p. 3705-3712.
Heithem Touazine, Mohammad Jahazi, Philippe Bocher.
2017.
« Accurate determination of damaged subsurface layers in machined Inconel 718 ».
International Journal of Advanced Manufacturing Technology.
vol. 88 , nº 9-12.
9 p.
p. 3419-3427.
Fubin Tu, Dorian Delbergue, Hongyan Miao, Thierry Klotz, Myriam Brochu, Philippe Bocher, Martin Levesque.
2017.
« A sequential DEM-FEM coupling method for shot peening simulation ».
Surface and Coatings Technology.
vol. 319
p. 200-212.
Maniya Aghasibeig, Hossein Monajatizadeh, Philippe Bocher, Ali Dolatabadi, Rolf Wuthrich, Christian Moreau.
2016.
« Cold spray as a novel method for development of nickel electrode coatings for hydrogen production ».
International Journal of Hydrogen Energy.
vol. 41 , nº 1.
p. 227-238.
Mohsen Mokhtabad Amrei, Hossein Monajati, Denis Thibault, Yves Verreman, Philippe Bocher.
2016.
« Effects of various post-weld heat treatments on austenite and carbide formation in a 13Cr4Ni steel multipass weld ».
Metallography, Microstructure, and Analysis.
vol. 5 , nº 1.
p. 50-61.
Mohsen Mokhtabad Amrei, Hossein Monajati, Denis Thibault, Yves Verreman, Lionel Germain, Philippe Bocher.
2016.
« Microstructure characterization and hardness distribution of 13Cr4Ni multipass weld metal ».
Materials Characterization.
vol. 111
p. 128-136.
M. Anderson, F. Bridier, J. Gholipour, M. Jahazi, P. Wanjara, P. Bocher, J. Savoie.
2016.
« Mechanical and metallurgical evolution of stainless steel 321 in a multi-step forming process ».
Journal of Materials Engineering and Performance.
vol. 25 , nº 4.
13 p.
p. 1526-1538.
N. Vanderesse, M. Anderson, F. Bridier, P. Bocher.
2016.
« Inter- and intragranular delta phase quantitative characterization in Inconel 718 by means of image analysis ».
Journal of Microscopy.
vol. 261 , nº 1.
p. 79-87.
N. Vanderesse, I. Ky, F. Quevedo Gonzalez, N. Nuño, P. Bocher.
2016.
« Image analysis characterization of periodic porous materials produced by additive manufacturing ».
Materials & Design.
vol. 92
p. 767-778.
W. Jomaa, V. Songmene, P. Bocher.
2016.
« An investigation of machining-induced residual stresses and microstructure of induction-hardened AISI 4340 steel ».
Materials and Manufacturing Processes.
vol. 31 , nº 7.
7 p.
p. 838-844.
Walid Jomaa, Victor Songmene, Philippe Bocher.
2016.
« An hybrid approach based on machining and dynamic tests data for the identification of material constitutive equations ».
Journal of Materials Engineering and Performance.
vol. 25 , nº 3.
p. 1010-1027.
Marc Novelli, Jean-Jacques Fundenberger, Philippe Bocher, Thierry Grosdidier.
2016.
« On the effectiveness of surface severe plastic deformation by shot peening at cryogenic temperature ».
Applied Surface Science.
vol. 389
p. 1169-1174.
A. Elhadi, A. Bouchoucha, W. Jomaa, Y. Zedan, T. Schmitt, P. Bocher.
2016.
« Study of surface wear and damage induced by dry sliding of tempered AISI 4140 steel against hardened AISI 1055 steel ».
Tribology in Industry.
vol. 38 , nº 4.
p. 475-485.
Meysam H. Pourian, Florent Bridier, Philippe Pilvin, Philippe Bocher.
2016.
« Prediction of crack initiation sites in alpha Ti-alloys microstructures under dwell-fatigue using Cellular Automaton simulation method ».
International Journal of Fatigue.
vol. 85
p. 85-97.
Vincent Savaria, Florent Bridier, Philippe Bocher.
2016.
« Predicting the effects of material properties gradient and residual stresses on the bending fatigue strength of induction hardened aeronautical gears ».
International Journal of Fatigue.
vol. 85
p. 70-84.
J. C. Stinville, M. P. Echlin, D. Texier, F. Bridier, P. Bocher, T. M. Pollock.
2016.
« Sub-grain scale digital image correlation by electron microscopy for polycrystalline materials during elastic and plastic deformation ».
Experimental Mechanics.
vol. 56 , nº 2.
p. 197-216.
D. Texier, Y. Zedan, T. Amoros, E. Feulvarch, J. C. Stinville, P. Bocher.
2016.
« Near-surface mechanical heterogeneities in a dissimilar aluminum alloys friction stir welded joint ».
Materials and Design.
vol. 108
p. 217-229.
Landry Giraud, Hugo Robe, Christophe Claudin, Christophe Desrayaud, Philippe Bocher, Eric Feulvarch.
2016.
« Investigation into the dissimilar friction stir welding of AA7020-T651 and AA6060-T6 ».
Journal of Materials Processing Technology.
vol. 235
p. 220-230.
Meysam Hamid Pourian, Philippe Pilvin, Florent Bridier, Philippe Bocher.
2015.
« Modeling the elastoplastic behaviors of alpha Ti-alloys microstructure using Cellular Automaton and finite element methods ».
Computational Materials Science.
vol. 99
p. 33-42.
N. Kamkar, F. Bridier, P. Jedrzejowski, Philippe Bocher.
2015.
« Water droplet impact erosion damage initiation in forged Ti-6Al-4V ».
Wear.
vol. 322-323
p. 192-202.
Mohsen Mokhtabad Amrei, Yves Verreman, Florent Bridier, Denis Thibault, Philippe Bocher.
2015.
« Microstructure characterization of single and multipass 13Cr4Ni steel welded joints ».
Metallography, Microstructure, and Analysis.
vol. 4 , nº 3.
p. 207-218.
Mathieu Paquin, Denis Thibault, Philippe Bocher, Jean-Benoît Lévesque, Yves Verreman, Kenji Shinozaki.
2015.
« Assessment of cold cracking tests for low transformation temperature martensitic stainless steel multipass welds ».
Welding in the World.
vol. 59 , nº 4.
p. 521-532.
Hugo Robe, Yasser Zedan, Jianqiang Chen, Hossein Monajati, Eric Feulvarch, Philippe Bocher.
2015.
« Microstructural and mechanical characterization of a dissimilar friction stir welded butt joint made of AA2024-T3 and AA2198-T3 ».
Materials Characterization.
vol. 110
p. 242-251.
V. Savaria, H. Monajati, F. Bridier, Philippe Bocher.
2015.
« Measurement and correction of residual stress gradients in aeronautical gears after various induction surface hardening treatments ».
Journal of Materials Processing Technology.
vol. 220
p. 113-123.
J. C. Stinville, F. Bridier, D. Ponsen, P. Wanjara, Philippe Bocher.
2015.
« High and low cycle fatigue behavior of linear friction welded Ti-6Al-4V ».
International Journal of Fatigue.
vol. 70
p. 278-288.
J. C. Stinville, N. Vanderesse, F. Bridier, P. Bocher, T. M. Pollock.
2015.
« High resolution mapping of strain localization near twin boundaries in a nickel-based superalloy ».
Acta Materialia.
vol. 98
p. 29-42.
Matteo Strano, Alessandro Marra, Valerio Mussi, Massimo Goletti, Philippe Bocher.
2015.
« Endurance of damping properties of foam-filled tubes ».
Materials.
vol. 8 , nº 7.
p. 4061-4079.
Lotfi Toubal, Philippe Bocher, André Moreau.
2015.
« Bimodal dwell-fatigue Weibull distribution of forged titanium IMI 834 ».
International Journal of Damage Mechanics.
vol. 24 , nº 5.
p. 629-645.
Majid Hoseini, Philippe Bocher, Arash Shahryari, Fereshteh Azari, Jerzy A. Szpunar, Hojatollah Vali.
2014.
« On the importance of crystallographic texture in the biocompatibility of titanium based substrate ».
Journal of Biomedical Materials Research - Part A.
vol. 102 , nº 10.
p. 3631-3638.
W. Jomaa, Victor Songmene, Philippe Bocher.
2014.
« Surface finish and residual stresses induced by orthogonal dry machining of AA7075-T651 ».
Materials.
vol. 7 , nº 3.
p. 1603-1624.
Maxime Lapalme, Majid Hoseini, Philippe Bocher, Alain R. Colle, Martin Levesque.
2014.
« Realistic cold expansion finite element model and experimental validations for aluminium alloys ».
Experimental Mechanics.
vol. 54 , nº 5.
p. 841-855.
A. Momeni, G. R. Ebrahimi, Mohammad Jahazi, Philippe Bocher.
2014.
« Microstructure evolution at the onset of discontinuous dynamic recrystallization: a physics-based model of subgrain critical size ».
Journal of Alloys and Compounds.
vol. 587
p. 199-210.
Gholam Reza Ebrahimi, Amir Momeni, Mohammad Jahazi, Philippe Bocher.
2014.
« Dynamic recrystallization and precipitation in 13Cr super-martensitic stainless steels ».
Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science.
vol. 45 , nº 4.
13 p.
p. 2219-2231.
Meysam H. Pourian, Philippe Pilvin, Florent Bridier, Philippe Bocher.
2014.
« Heterogeneous elastic behavior of HCP titanium polycrystalline aggregates simulated by cellular automaton and finite element ».
Computational Materials Science.
vol. 92
p. 468-475.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault.
2014.
« Influence of load spectrum assumptions on the expected reliability of hydroelectric turbines: A case study ».
Structural Safety.
vol. 50
p. 1-8.
J. Ruiz-Vargas, N. Siredey-Schwaller, P. Noyrez, S. Mathieu, Philippe Bocher, N. Gey.
2014.
« Potential and limitations of microanalysis SEM techniques to characterize borides in brazed Ni-based superalloys ».
Materials Characterization.
vol. 94
p. 46-57.
Melissa Anderson, Javad Gholipour, Florent Bridier, Philippe Bocher, Mohammad Jahazi, Jean Savoie, Priti Wanjara.
2013.
« Improving the formability of stainless steel 321 through multistep deformation for hydroforming applications ».
Transactions of the Canadian Society for Mechanical Engineering.
vol. 37 , nº 1.
p. 39-52.
J. Yi, M. Gharghouri, Philippe Bocher, M. Medraj.
2013.
« Distortion and residual stress measurements of induction hardened AISI 4340 discs ».
Materials Chemistry and Physics.
vol. 142 , nº 1.
p. 248-258.
N. Barka, Philippe Bocher, J. Brousseau.
2013.
« Sensitivity study of hardness profile of 4340 specimen heated by induction process using axisymmetric modeling ».
International Journal of Advanced Manufacturing Technology.
vol. 69 , nº 9-12.
p. 2747-2756.
N. Boutana, P. Bocher, M. Jahazi.
2013.
« Discrepancy between fatigue and dwell-fatigue behavior of near alpha titanium alloys simulated by cellular automata ».
International Journal of Fatigue.
vol. 51
p. 49-56.
N. Kamkar, Florent Bridier, Philippe Bocher, P. Jedrzejowski.
2013.
« Water droplet erosion mechanisms in rolled Ti-6Al-4V ».
Wear.
vol. 301 , nº 1-2.
p. 442-448.
Benjamin Larregain, Nicolas Vanderesse, Florent Bridier, Philippe Bocher, Patrick Arkinson.
2013.
« Method for accurate surface temperature measurements during fast induction heating ».
Journal of Materials Engineering and Performance.
vol. 22 , nº 7.
p. 1907-1913.
A. R. Maldar, G. R. Ebrahimi, Meysam Haghshenas, M. Jahazi, P. Bocher.
2013.
« Thermomechanical characterization of Mg-9Al-1Zn alloy using power dissipation maps ».
Journal of Materials Engineering and Performance.
vol. 22 , nº 11.
p. 3306-3314.
A. Moreau, L. Toubal, Philippe Bocher, M. Humbert, E. Uta, N. Gey.
2013.
« Evaluation of macrozone dimensions by ultrasound and EBSD techniques ».
Materials Characterization.
vol. 75
p. 115-128.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault.
2013.
« A probabilistic model for the onset of High Cycle Fatigue (HCF) crack propagation: Application to hydroelectric turbine runner ».
International Journal of Fatigue.
vol. 47
p. 300-307.
A. Gariepy, F. Bridier, M. Hoseini, Philippe Bocher, C. Perron, M. Levesque.
2013.
« Experimental and numerical investigation of material heterogeneity in shot peened aluminium alloy AA2024-T351 ».
Surface and Coatings Technology.
vol. 219
p. 15-30.
J. Ruiz-Vargas, N. Siredey-Schwaller, Philippe Bocher, A. Hazotte.
2013.
« First melting stages during isothermal brazing, of Ni/BNi-2 couples ».
Journal of Materials Processing Technology.
vol. 213 , nº 12.
p. 2074-2080.
A. Gariepy, S. Larose, C. Perron, Philippe Bocher, M. Levesque.
2013.
« On the effect of the orientation of sheet rolling direction in shot peen forming ».
Journal of Materials Processing Technology.
vol. 213 , nº 6.
p. 926-938.
A. Gariepy, S. Larose, C. Perron, Philippe Bocher, M. Levesque.
2013.
« On the effect of the peening trajectory in shot peen forming ».
Finite Elements in Analysis and Design.
vol. 69
p. 48-61.
Majid Hoseini, Meysam Hamid Pourian, Florent Bridier, Hojatollah Vali, Jerzy A. Szpunar, Philippe Bocher.
2012.
« Thermal stability and annealing behaviour of ultrafine grained commercially pure titanium ».
Materials Science and Engineering A.
vol. 532
p. 58-63.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault.
2012.
« On the stochastic simulation of hydroelectric turbine blades transient response ».
Mechanical Systems and Signal Processing.
vol. 32
p. 178-187.
J. Ruiz-Vargas, N. Siredey-Schwaller, N. Gey, P. Bocher, A. Hazotte.
2012.
« Microstructure development during isothermal brazing of Ni/BNi-2 couples ».
Journal of Materials Processing Technology.
vol. 213 , nº 1.
p. 20-29.
Vincent Savaria, Florent Bridier, Philippe Bocher.
2012.
« Computational quantification and correction of the errors induced by layer removal for subsurface residual stress measurements ».
International Journal of Mechanical Sciences.
vol. 64 , nº 1.
p. 184-195.
A. Gariepy, J. Cyr, A. Levers, C. Perron, P. Bocher, M. Lévesque.
2012.
« Potential applications of peen forming finite element modelling ».
Advances in Engineering Software.
vol. 52
p. 60-71.
N. Gey, P. Bocher, E. Uta, L. Germain, M. Humbert.
2012.
« Texture and microtexture variations in a near-α titanium forged disk of bimodal microstructure ».
Acta Materialia.
vol. 60 , nº 6-7.
p. 2647-2655.
Alessandro Candeo, Christophe Ducassy, Philippe Bocher, Fabrizio Dughiero.
2011.
« Multiphysics modeling of induction hardening of ring gears for the aerospace industry ».
IEEE Transactions on Magnetics.
vol. 47 , nº 5.
p. 918-921.
Denis Thibault, Philippe Bocher, Marc Thomas, Jacques Lanteigne, Pierre Hovington, Patrice Robichaud.
2011.
« Reformed austenite transformation during fatigue crack propagation of 13%Cr-4%Ni stainless steel ».
Materials Science and Engineering A.
vol. 528 , nº 21.
p. 6519-6526.
M. Anderson, J. Gholipour, Philippe Bocher, F. Bridier, J. Savoie, P. Wanjara.
2010.
« Formability extension of aerospace alloys for tube hydroforming applications ».
International Journal of Material Forming.
vol. 3 , nº Suppl. 1.
p. 303-306.
N. Bastajib, N. Boutana, P. Bocher, M. Jahazi.
2010.
« Application of cellular automata method to simulate the hot deformation behavior of a dual phase titanium alloy ».
Technische Mechanik.
vol. 30 , nº 1-3.
14 p.
Denis Thibault, Philippe Bocher, Marc Thomas, Michael Gharghouri, Marjolaine Coté.
2010.
« Residual stress characterization in low transformation temperature 13%Cr-4%Ni stainless steel weld by neutron diffraction and the contour method ».
Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing.
vol. 527 , nº 23.
p. 6205-6210.
Lotfi Toubal, Philippe Bocher, André Moreau, Daniel Levesque.
2010.
« Macroregion size measurements in bimodal titanium forgings using two-dimensional autocorrelation method ».
Metallurgical and Materials Transactions a-Physical Metallurgy and Materials Science.
vol. 41A , nº 3.
p. 744-750.
L. Hacini, Van Ngan Lê, Philippe Bocher.
2009.
« Evaluation of residual stresses induced by robotized hammer peening by the contour method ».
Experimental Mechanics.
vol. 49 , nº 6.
p. 775-783.
M. Humbert, A. Moreau, E. Uta, N. Gey, Philippe Bocher, C. Bescond.
2009.
« Analysis of backscattered ultrasound amplitude of Ti-5.8Al-4Sn-3.5Zr-0.7Nb-0.5Mo-0.3Si samples in terms of their microstructures and local textures ».
Acta Materialia.
vol. 57 , nº 3.
p. 708-714.
Denis Thibault, Philippe Bocher, Marc Thomas.
2009.
« Residual stress and microstructure in welds of 13%Cr-4%Ni martensitic stainless steel ».
Journal of Materials Processing Technology.
vol. 209 , nº 4.
p. 2195-2202.
Lotfi Toubal, Philippe Bocher, André Moreau.
2009.
« Dwell-fatigue life dispersion of a near alpha titanium alloy ».
International Journal of Fatigue.
vol. 31 , nº 3.
p. 601-605.
E. Uta, N. Gey, Philippe Bocher, M. Humbert, J. Gilgert.
2009.
« Texture heterogeneities in alpha(p)/alpha(s) titanium forging analysed by EBSD-Relation to fatigue crack propagation ».
Journal of Microscopy.
vol. 233 , nº 3.
p. 451-459.
Lyes Hacini, Van Ngan Lê, Philippe Bocher.
2008.
« Effect of impact energy on residual stresses induced by hammer peening of 304L plates ».
Journal of Materials Processing Technology.
vol. 208 , nº 1-3.
p. 542-548.
N. Boutana, P. Bocher, M. Jahazi, D. Piot, F. Montheillet.
2008.
« Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ».
Transactions of the Canadian Society for Mechanical Engineering.
vol. 32 , nº 2.
p. 195-213.
N. Boutana, Philippe Bocher, M. Jahazi, D. Piot, F. Montheillet.
2008.
« The microstructural modeling of room temperature creep in titanium alloys using cellular automata model ».
International Journal of Microstructure and Materials Properties.
vol. 3 , nº 4-5.
p. 642-653.
L. Germain, N. Gey, M. Humbert, P. Vo, M. Jahazi, Philippe Bocher.
2008.
« Texture heterogeneities induced by subtransus processing of near alpha titanium alloys ».
Acta Materialia.
vol. 56 , nº 16.
p. 4298-4308.
M. A. Arafin, M. Medraj, D. P. Turner, Philippe Bocher.
2007.
« Effect of alloying elements on the isothermal solidification during TLP bonding of SS 410 and SS 321 using a BNi-2 interlayer ».
Materials Chemistry and Physics.
vol. 106 , nº 1.
p. 109-119.
Phuong Vo, M. Jahazi, S. Yue, Philippe Bocher.
2007.
« Flow stress prediction during hot working of near-alpha titanium alloys ».
Materials Science and Engineering : A.
vol. 447 , nº 1-2.
p. 99-110.
M. A. Arafin, M. Medraj, Daniel P. Turner, Philippe Bocher.
2007.
« Transient liquid phase bonding of Inconel 718 and Inconel 625 with BNi-2: modeling and experimental investigations ».
Materials Science and Engineering : A.
vol. 447 , nº 1-2.
p. 125-133.
Michel Humbert, L. Germain, N. Gey, Philippe Bocher, M. Jahazi.
2006.
« Study of the variant selection in sharp textured regions of bimodal IMI 834 billet ».
Materials Science and Engineering : A.
vol. 430 , nº 1-2.
p. 157-164.
Philippe Bocher, Mohammad Jahazi, Lionel Germain, Priti Wanjara, Nathalie Gey, Michel Humbert.
2005.
« β Microtexture analysis in correlation with hcp textured regions observed in a forged near alpha titanium alloy ».
Solid State Phenomena.
vol. 105
p. 127-132.
Ali Reza Khodabandeh, Mohammad Jahazi, Steve Yue, Philippe Bocher.
2005.
« Impact toughness and tensile properties improvement through microstructure control in hot forged Nb-V microalloyed steel ».
ISIJ International.
vol. 45 , nº 2.
p. 272-280.
L. Germain, N. Gey, M. Humbert, A. Hazotte, P. Bocher, M. Jahazi.
2005.
« An automated method to analyze separately the microtextures of primary αp grains and the secondary αs inherited colonies in bimodal titanium alloys ».
Materials Characterization.
vol. 54 , nº 3.
p. 216-222.
Lionel Germain, Nathalie Gey, Ludovic Humbert, Philippe Bocher, Mohammad Jahazi.
2005.
« Analysis of sharp microtexture heterogeneities in a bimodal IMI 834 billet ».
Acta Materialia.
vol. 53 , nº 13.
p. 3535-3543.
Mohammad Jahazi, Lionel Germain, Nathalie Gey, Michel Humbert, Philippe Bocher.
2004.
« Specific EBSD data processing to analyse separately the ap/as microtexture of bimodal Titanium alloys ».
Materials Characterization.
vol. 54
p. 216-222.
Quentin Boyadjian, Nicolas Vanderesse, Matthew Toews, Philippe Bocher.
2020.
« Detecting defects in materials using deep convolutional neural networks ».
Image Analysis and Recognition : 17th International Conference, ICIAR 2020, Póvoa de Varzim, Portugal, June 24–26, 2020, Proceedings, Part I (Póvoa de Varzim, Portugal, June 24-26, 2020)
p. 293-306.
Springer.
Pierre Maurel, Laurent Weiss, Philippe Bocher, Eric Fleury, Thierry Grosdidier.
2020.
« Mechanisms of oxide dependent tribological behavior in Ti / Steel sliding and influence of nanostructured surfaces ».
14th World Conference on Titanium (Ti 2019) (Nantes, France, June 10-14, 2020)
EDP Sciences.
Hamid Javadi, Walid Jomaa, Elvi Dalgaard, Myriam Brochu, Philippe Bocher.
2018.
« Influence of surface residual stresses on the fatigue life and crack propagation behavior of turned Inconel 718 super-alloy ».
12th International Fatigue Congress (FATIGUE 2018) (Poitiers, France, May 27-June 1, 2018)
EDP Sciences.
Kamel Touahir, Ali Bilek, Said Larbi, Said Djebali, Philippe Bocher.
2018.
« 3D stress analysis of a loaded birefringent sphere by photoelastic experiment and finite elements method ».
24th Conference on Applications of Computer Algebra (Santiago de Compostela, Spain, June 18-22, 2018)
Hamid Javadi, Walid Jomaa, Damien Texier, Myriam Brochu, Philippe Bocher.
2017.
« Surface roughness effects on the fatigue behavior of as-machined inconel 718 ».
8th International Conference on Materials Structure and Micromechanics of Fracture (MSMF 8) (Brno, Czech republic, July 27-29, 2016)
p. 306-309.
Trans Tech Publications Ltd.
Walid Jomaa, Victor Songmene, Philippe Bocher, Augustin Gakwaya.
2017.
« Fea-based comparative investigation on high speed machining of aluminum alloys aa6061-t6 and aa7075-t651 ».
9th International Congress on Precision Machining, (ICPM 2017) (Athens, Greece, Sept. 06-09, 2017)
p. 347-353.
D. Delbergue, M. Lévesque, P. Bocher.
2017.
« About the importance of X-ray elastic constant determination in the precise measurement of residual stress profiles ».
13th International Conference on Shot Peening (ICSP) (Montréal, QC, Canada, 18-21 sept. 2017)
p. 237-243.
D. Delbergue, D. Texier, M. Lévesque, P. Bocher.
2017.
« Comparison of two X-Ray residual stress measurement methods: Sin2 ψ and Cos α, through the determination of a martensitic steel X-Ray elastic constant ».
International Conference on Residual Stresses 2016 ICRS-10
p. 55-60.
Millersville : Materials Research Forum LLC.
V. Demers, M. M. Elmajdoubi, P. Bocher.
2017.
« Moldability of low-pressure powder injection molding feedstocks ».
Advances in Powder Metallurgy & Particulate Materials 2017 : Conference Proceedings (Las Vegas , NV, USA, June 13-16, 2017)
p. 401-414.
Metal Powder Industries Federation.
W. Jomaa, J. Mechri, J. Lévesque, A. Gakwaya, V. Songmene, P. Bocher.
2016.
« Finite element analysis of serrated chip formation in machining of 7075-T651 alluminum alloy ».
XXVIII International Mineral Processing Congress (IMPC) (Québec, QC, Canada, Sept. 11-15, 2016)
Pierre Comot, Philippe Bocher, Pierre Belanger.
2016.
« Ultrasonic guided wave inspection of Inconel 625 brazed lap joints ».
Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, and Civil Infrastructure 2016 (Las Vegas , NV, USA, Mar. 20-24, 2016)
SPIE.
Mahdi Masoumi, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher.
2016.
« Friction stir welding of AA2024 and AA2198 Aluminum alloys: effect of tool geometry and process parameters ».
2nd International Conference on Welding and Non Destructive Testing (ICWNDT) (Tehran, Iran, Dec. 20-21, 2016)
Mahdi Masoumi, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher.
2016.
« The influence of tool geometry on mechanical properties of friction stir welded AA-2024 and AA-2198 joints ».
34th International Conference and Exhibition of ICSOBA (Quebec, QC, Canada, Oct. 03-06, 2016)
The International Committee for Study of Bauxite, Alumina & Aluminium (ICSOBA).
Hesser Taboada Michel, Layla Sasaki Reda, Georgia Effgen Santos, Jonathan Cormier, Christian Dumont, Patrick Villechaise, Philippe Bocher, Damien Texier, Eric Georges, Florent Bridier, Florence Hamon, Alexandre Devaux.
2016.
« Mechanical properties of cast wrought hybrid disks ».
Superalloys 2016: Proceedings of the 13th International Symposium on Superalloys (Seven Springs, PA, USA, Sept. 11-15, 2016)
p. 539-548.
Minerals, Metals and Materials Society.
Kevin McMeekn, Frédéric Sirois, Philippe Bocher, Maxime Tousignant.
2015.
« Equivalent permeability model to simplify the nonlinear hysteretic B-H curve in time harmonic FEM simulations of induction heating ».
20th International Conference on the Computation of Electromagnetic Fields (Compumag 2015) (Montréal, QC, Canada, June 28-July 2, 2015)
p. 333-334.
International Compumag Society.
F. Quevedo, N. Vanderesse, P. Bocher, N. Nuño.
2015.
« Characterization and simulation of manufacturing irregularities of additive manufactured well-ordered porous materials ».
Advanced Manufacturing Canada (AMC 2015) (Montreal, QC, Canada, Nov. 18-19, 2015)
Walid Jomaa, Monzer Daoud, Victor Songmene, Philippe Bocher, Jean-François Châtelain.
2014.
« Identification and validation of Marusich's constitutive law for finite element modeling of high speed machining ».
ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014)
American Society of Mechanical Engineers (ASME).
Florent Bridier, Jean-Charles Stinville, Nicolas Vanderesse, Patrick Villechaise, Philippe Bocher.
2014.
« Microscopic strain and crystal rotation measurement within metallurgical grains ».
Materials Structure and Micromechanics of Fracture VII (Brno, Czech Republic, July 1-3, 2013)
p. 493-496.
Trans Tech Publications Ltd.
Vincent Savaria, Florent Bridier, Philippe Bocher.
2014.
« Measuring in-depth residual stress gradients: The challenge of induction hardened parts ».
International Conference on Residual Stresses 9 (ICRS 9) (Garmisch-Partenkirchen, Germany, Oct. 7-9, 2012)
p. 158-165.
Zurich-Durnten, Switzerland : Trans Tech Publications Ltd.
H. Touazine, Mohammad Jahazi, Philippe Bocher.
2014.
« Influence of hard turning on microstructure evolution in the subsurface layers of Inconel 718 ».
ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014)
American Society of Mechanical Engineers (ASME).
Amir Ansaripour, Hossein Monajatizadeh, Philippe Bocher, Davoud Asefi.
2013.
« Evaluation of recovery and recrystallization in cold rolled low carbon steel by magnetic hysteresis loop measurements ».
Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
p. 225-233.
Warrendale, PA, USA : Association for Iron and Steel Technology.
W. Jomaa, Victor Songmene, Philippe Bocher.
2013.
« On residual stress changes after orthogonal machining of induction hardened AISI 4340 steel ».
Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
p. 94-103.
Warrendale, PA, USA : Association for Iron and Steel Technology.
Noureddine Barka, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau.
2013.
« Effects of material properties fornon-equilibrium conditions in induction heating process ».
Environmental and Materials Engineering (Seoul, Korea, Dec. 9-10, 2012)
p. 496-503.
Clausthal-Zellerfeld, Germany : Trans Tech Publications Ltd.
Noureddine Barka, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau.
2013.
« Explorative study and prediction of overtemperingregion of disc heated by induction process using 2D axisymmetric model and experimental tests ».
Materials and Manufacturing Research (Hong Kong, China, Dec. 19-20, 2012)
p. 259-265.
Trans Tech Publications.
Noureddine Barka, Abdel Jelil Khelalfa, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau.
2013.
« Effect of skin depth on hardness profile of gear heated by induction using 2D model ».
Environmental and Materials Engineering (Seoul, Korea, Dec. 9-10, 2012)
p. 884-890.
Clausthal-Zellerfeld, Germany : Trans Tech Publications Ltd.
Noureddine Barka, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau, Ahmed Chebak.
2013.
« Explorative study and prediction of overtempering region of disc heated by induction process using 2D axisymmetric model and experimental tests ».
Materials Engineering for Advanced Technologies (ICMEAT 2012) (Xiamen, China, Dec. 27-28, 2012)
p. 417-423.
Scientific.net.
Rabih Kassab, Henri Champliaud, Philippe Bocher, Jacques Lanteigne, Van Ngan Lê.
2013.
« Strain variations of AISI 4340 steel undergoing metallurgical transformations during induction hardening heat treatment ».
Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
p. 774-783.
Warrendale, PA, USA : Association for Iron and Steel Technology.
M. Paquin, D. Thibault, Philippe Bocher, Y. Verreman.
2013.
« Study on cold cracking test methods for low carbon soft-martensitic stainless steel flux cored arc welding ».
Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013)
p. 733-744.
Warrendale, PA, USA : Association for Iron and Steel Technology.
M. Gagnon, Antoine Tahan, Philippe Bocher, D. Thibault.
2013.
« On the fatigue reliability of hydroelectric Francis runners ».
5th International Conference on Fatigue Design, Fatigue Design 2013 (Senlis, France, Nov. 27-28, 2013)
p. 565-574.
D. Shahriari, A. Zolfaghari, Mohammad Jahazi, Philippe Bocher.
2013.
« Development of an expert system to characterize weld defects identified by ultrasonic testing ».
American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP (Paris, France, July 14-18, 2013)
New York, NY, USA : American Society of Mechanical Engineers.
Majid Hoseini, Philippe Bocher, Fereshteh Azari, Hojatollah Vali, Jerzy A. Szpunar.
2012.
« Effects of grain size and texture on the biocompatibility of commercially pure titanium ».
16th International Conference on Textures of Materials (Mumbai, India, Dec. 12-17, 2011 )
p. 822-825.
Trans Tech Publications Ltd.
Melissa Anderson, Philippe Bocher, Javad Gholipour, Mohammad Jahazi, Jean Savoie, Priti Wanjara.
2012.
« Increasing the hydroformability of stainless steel 321 by multistep processing ».
Proceedings of the 14th International Conference on Metal Forming, METAL FORMING 2012 (Krakow, Poland, Sept. 16-19, 2012)
p. 1243-1246.
Krakow, Poland : Wiley-VCH Verlag.
Majid Hoseini, Florent Bridier, Philippe Bocher, Hojatollah Vali, Jerzy A. Szpunar.
2012.
« Thermal stability and grain growth behavior of ultrafine grained commercially pure titanium fabricated by equal channel angular pressing ».
Ti 2011 - Proceedings of the 12th World Conference on Titanium (Beijing, China, June 19-24, 2011)
p. 666-670.
Beijing, China : Science Press.
Noureddine Barka, Ahmed Chebak, Abderrazakel Ouafi, Philippe Bocher, Jean Brousseau.
2012.
« Sensitivity study of temperature profile of 4340 spur gear heated by induction process using 3D model ».
Mechanical and Aerospace Engineering (Paris, France, July 7-8, 2012)
p. 736-741.
Trans Tech Publications.
Noureddine Barka, Abderrazak El Ouafi, Ahmed Chebak, Philippe Bocher, Jean Brousseau.
2012.
« Study of induction heating process applied to internal gear using 3D model ».
Mechanical and Aerospace Engineering (Paris, France, July 7-8, 2012)
p. 730-735.
Trans Tech Publications.
M. Gagnon, Antoine Tahan, Philippe Bocher, D. Thibault.
2012.
« The role of high cycle fatigue (HCF) onset in Francis runner reliability ».
26th IAHR Symposium on Hydraulic Machinery and Systems (Beijing, China, Aug. 19-23, 2012)
UK : IOP Publishing Ltd..
N. Gey, Philippe Bocher, E. Uta, M. Humbert, J. Gilgert.
2012.
« How texture and microtexture influence dwell fatigue lifetime in forged IMI834 titanium alloys ».
Ti 2011 - Proceedings of the 12th World Conference on Titanium (Beijing, China, June 19-24, 2011)
p. 879-882.
Beijing, China : Science Press.
N. Barka, Philippe Bocher, J. Brousseau, P. Arkinson.
2011.
« Effect of dimensional variation on induction process parameters using 2D simulation ».
THERMEC 2011 Supplement (Quebec City, QC, Canada, Aug. 1-5, 2011)
p. 395-400.
Germany : Trans Tech Publications.
Vincent Savaria, Majid Hoseini, Florent Bridier, Philippe Bocher, Patrick Arkinson.
2011.
« On the measurement of residual stress in induction hardened parts ».
Residual Stresses VIII (Riva del Garda, Trento, Italy, June 26-28, 2010)
p. 431-436.
Alessandro Candeo, Philippe Bocher, Fabrizio Dughiero.
2010.
« Multiphysics modeling of induction hardening of ring gears for the aerospace industry ».
14th Biennial IEEE Conference on Electromagnetic Field Computation (CEFC 2010) (Chicago, IL, USA, May 09-12, 2010)
IEEE.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault.
2010.
« Impact of startup scheme on Francis runner life expectancy ».
25th IAHR Symposium on Hydraulic Machinery and Systems (Timisoara, Romania, 20–24 Sept. 2010)
p. 12107.
London, UK : Institute of Physics Publishing.
Philippe Bocher, F. Bridier, L. Toubal, N. Boutana, E. Uta, N. Gey, M. Humbert.
2009.
« Dwell-fatigue in near alpha titanium alloys: A multiscale, interdisciplinary challenge ».
12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009)
p. 1481-1486.
International Congress on Fracture.
L. Toubal, Philippe Bocher, A. Moreau.
2009.
« Dwell-fatigue life of a near-alpha titanium alloy and ultrasonic measurement correlation ».
12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009)
p. 1123-1128.
International Congress on Fracture.
André Moreau, Silvio E. Kruger, Marjolaine Côté, Philippe Bocher.
2008.
« In-Situ monitoring of microstructure during thermomechanical simulations using laser-ultrasonics ».
1st Interntional Symposium on Laser Ultrasonics : Science, Technology and Applications (Montreal, QC, Canada, July 16-18, 2008)
E. Uta, Philippe Bocher, N. Gey, M. Humbert, J. Gilgert.
2008.
« EBSD analyses of dwell fracture surface in titanium alloy IMI-834 ».
International Conference Fatigue and Plasticity From Mechanisms to Design (JIP) (Paris, France, May 20-22, 2008)
p. 315-322.
L. Hacini, Van Ngan Lê, Philippe Bocher.
2007.
« Traitement de surfaces par impacts : évaluation des contraintes résiduelles induites par martelage ».
18e Congrès Français de Mécanique (Grenoble, France, 27-31 août 2007)
Courbevoie, France : AFM, Maison de la Mécanique.
E. Uta, M. Humbert, N. Gey, A. Hazotte, Philippe Bocher, M. Jahazi.
2007.
« Description and characterisation of texture heterogeneitites in titanium alloy Timetal 834 with a bimodal microstructure ».
11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007)
p. 259-262.
Warrendale, USA : Minerals, Metals and Materials Society.
N. Boutana, Philippe Bocher, M. Jahazi, D. Piot, F. Motheillet.
2007.
« Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ».
Proceedings of TI-2007, 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007)
p. 267-270.
Warrendale, PA, USA : Minerals, Metals and Materials Society.
Lionel Germain, Phuong Vo, Nathalie Gey, Mohammad Jahazi, Michel Humbert, Philippe Bocher.
2007.
« Development of sharp local α microtextures during α/β thermo-mechanical processing of TIMETAL 834 ».
11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007)
p. 925-928.
Warrendale, USA : Minerals, Metals and Materials Society.
L. Hacini, Van Ngan Lê, Philippe Bocher, D. Thibault.
2006.
« Effect of energy level on stresses induced by robotized hammer peening ».
Conference of Metallurgists (COM) (Montreal, QC, Canada, Oct.1-4, 2006)
p. 781-790 .
Montreal, Canada : The Metallurgy and Materials Society of CIM.
L. Hacini, Van Ngan Lê, Philippe Bocher, D. Thibault.
2006.
« Residual stresses induced by robotized hammer peening : the effect of impact energy level ».
Aerospace materials and manufacturing : emerging materials, processes, and repair techniques : proceedings of the third International [Symposium] on Aerospace Materials and Manufacturing : emerging materials, processes and repair techniques, October 1-4, (Montreal, QC, Canada, Oct. 2-4, 2006)
p. 759-768.
Montreal : Canadian Institute of Mining, Metallurgy and Petroleum.
E. Uta, M. Humbert, N. Gey, P. Bocher, M. Jahazi.
2006.
« Mise en évidence et caractérisation des hétérogénéités de textures dans l'alliage de titane IMI 834 de microstructure bimodale à vocation aéronautique ».
Materiaux 2006 : Dijon, 13-17 Novembre 2006 : [recueil de la conference sur CD-ROM] (Dijon, France, 13-17 nov. 2006)
Dijon : Université de Bourgogne.
M. A. Arafin, M. Medraj, D. P. Turner, P. Bocher.
2006.
« Optimization of process variables during TLP Bonding of nickel superalloys ».
Aerospace materials and manufacturing : emerging materials, processes, and repair techniques : proceedings of the third International [Symposium] on Aerospace Materials and Manufacturing : emerging materials, processes and repair techniques, October 1-4, (Montreal, QC, Canada, Oct. 1-4, 2006)
p. 301-314.
Canadian Institute of Mining, Metallurgy and Petroleum.
M. A. Arafin, M. Medraj, D. P. Turner, Philippe Bocher.
2006.
« Thermodynamic modeling and experimental investigation of brazed joints used in aerospace industry ».
3rd International Brazing and Soldering Conference (San Antonio, TX, USA, April 24-26, 2006)
p. 189-196.
Materials Park, OH, USA : ASM International.
Muhammad A. Arafin, Mamoun Medraj, Daniel P. Turner, Philippe Bocher.
2006.
« Mathematical Modeling and Experimental Investigations of Isothermal Solidification during Transient Liquid Phase Bonding of Nickel Superalloys ».
THERMEC 2006 Supplement (Vancouver, Canada, Jul. 4 - 8, 2006)
p. 882-887.
Clausthal-Zellerfeld, Germany : Trans Tech Publications.
N. Barka, Philippe Bocher, J. Brousseau, Michel Galopin, S. Sundararajan.
2006.
« Modeling and sensitivity study of the induction hardening process ».
THERMEC 2006 Supplement (Vancouver, Canada, Jul. 4-8, 2006)
p. 525-530.
Uetikon-Zuerich, Switzerland : Trans Tech Publications.
N. Barka, Philippe Bocher, Michel Galopin, J. Brousseau, S. Sundararajan.
2006.
« Sensitivity study of induction hardening machine parameters of SAE-4340 steel specimen ».
Conference of Metallurgists (COM) (Montreal, QC, Canada, Oct. 1-4, 2006)
p. 525-530.
Montreal, Canada : The Metallurgy and Materials Society of CIM.
Nabil Boutana, Philippe Bocher, Mohammad Jahazi, D. Piot, F. Montheillet.
2006.
« Utilisation des automates cellulaires pour étudier le comportement en fatigue-fluage des alliages de titane ».
Matériaux 2006 (Dijon, France, 13-17 nov. 2006)
p. 781-790.
L. Dubourg, M. Jahazi, G. Dezaise, P. Bocher.
2006.
« Microstructure and mechanical characterisation of FSW 7075-T6 lap joints ».
Aerospace Materials and Manufacturing: Emerging Materials, Processes, and Repair Techniques (Montréal, Canada, Oct.1-4, 2006)
p. 107-120.
Canadian Institute of Mining, Metallurgy and Petroleum.
P. Wanjara, H. Monajati, M. Jahazi, L. Germain, P. Bocher, J.-P. Immarigeon.
2005.
« Deformation processing mechanism and microstructural evolution in a near-alpha titanium alloy ».
Materials science & technology: proceedings of the conference held September 25-28, 2005, Pittsburgh, Pennsylvania USA (Pittsburgh, PA, USA, Sept. 25-28, 2005)
p. 15-26.
Association for Iron and Steel Technology.
P. Bocher, M. Jahazi, L. Germain, N. Gey, M. Humbert.
2005.
« Variant selection in forged titanium alloys : effect of microscopic grain misorientations on the formation of macroscopic regions with similar crystallographic orientations ».
Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, QC, Canada, Aug. 1-4, 2005)
p. 523-530.
Montréal, Qué., Canada : École de technologie supérieure.
N. Boutana, P. Bocher, M. Jahazi, J. Savoie, D. Piot, F. Montheillet.
2005.
« Modelling mechanical behaviour of heterogeneous materials using cellular automata : application to some forged titanium alloys ».
Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, QC, Canada, Aug. 1-4, 2005)
p. 273-280.
Montréal, Qué., Canada : École de technologie supérieure.
L. Germain, N. Gey, M. Humbert, P. Bocher, M. Jahazi.
2003.
« Texture and microtexture analysis of an IMI 834 alloy after thermo-mechanical processing ».
Ti-2003 Science and Technology : proceedings of the 10th World Conference on Titanium held at the CCH-Congress Center Hamburg, Germany, 13-18 July 2003 (Hamburg, Germany, July 13-18, 2003)
p. 1283-1290.
Weinheim, Allemagne : Wiley-VCH.