Publications
Sevan Bouchy, Ricardo J. Zednik, Pierre Belanger. 2023. « Ultrasonic transducers for in-service inspection and continuous monitoring in high-temperature environments ». Sensors. vol. 23 , nº 7.
Baptiste Gauthier, Guillaume Painchaud-April, Alain Le Duff, Pierre Bélanger. 2023. « Ultrasonic multi-view data merging using the vector coherence factor ». NDT and E International. vol. 136
Jorge Franklin Mansur Rodrigues Filho, Pierre Bélanger. 2023. « Global total focusing method through digital twin and robotic automation for ultrasonic phased array inspection of complex components ». NDT and E International. vol. 137
Nathan Molinier, Guillaume Painchaud-April, Alain Le Duff, Matthew Toews, Pierre Bélanger. 2023. « Ultrasonic imaging using conditional generative adversarial networks ». Ultrasonics. vol. 133
Lucas Pereira Piedade, Guillaume Painchaud-April, Alain Le Duff, Pierre Belanger. 2023. « Compressive sensing strategy on sparse array to accelerate ultrasonic TFM imaging ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 70 , nº 6. p. 538-550.
Aurélien Thon, Guillaume Painchaud-April, Alain Le Duff, Pierre Bélanger. 2023. « Development of a linear array electromagnetic acoustic transducer for shear horizontal guided wave inspection ». NDT and E International. vol. 136
Aurelien Thon, Guillaume Painchaud-April, Alain Le Duff, Pierre Bélanger. 2023. « On the use of a linear array EMAT for remote thickness gauging using the reflected modes on a steel pipe ». NDT and E International. vol. 139
Bhupesh Verma, Pierre Bélanger. 2023. « An alternative Rayleigh wave excitation method using an ultrasonic phased array ». Ultrasonics. vol. 135
Hossein Taheri Barayjani, Mohammad Reza Toroghinejad, Ahmad Rezaeian, Ali Shabani, Philippe Bocher. 2023. « An investigation on microstructure and mechanical properties of a copper strip subjected to different routes of accumulative roll bonding process ». Journal of Materials Engineering and Performance. vol. 32 , nº 2. p. 651-659.
Loïc Villié, Elodie Cabrol, Lucas Hof, Eric Feulvarch, Philippe Bocher. 2023. « Heterogeneities induced by uniaxial compression and resulting errors in material behavior assessment ». International Journal of Material Forming. vol. 16 , nº 6.
Mahshad Javidikia, Morteza Sadeghifar, Henri Champliaud, Mohammad Jahazi. 2023. « Grain size and temperature evolutions during linear friction welding of Ni-base superalloy Waspaloy: Simulations and experimental validations ». Journal of Advanced Joining Processes. vol. 8
Jean-Philippe Noel, Raynald Guilbault, Christian Perreault, Karim Zaghib. 2023. « Numerical optimization of lithium-ion cell performance using metaheuristic algorithms ». Journal of Energy Storage. vol. 71
Douglas F. Cole, Ricardo J. Zednik, Lucas A. Hof. 2023. « High aspect ratio sapphire micromachining by ultraviolet laser-induced plasma-assisted ablation (LIPAA) ». International Journal of Applied Ceramic Technology. vol. 20 , nº 5. p. 3279-3286.
Victor Delpla, Kevin Chapron, Jean-Pierre Kenné, Lucas A. Hof. 2023. « A novel approach for predicting Lockout/Tagout safety procedures for smart maintenance strategies ». International Journal of Production Research. (Sous presse)
Victor Delpla, Jean-Pierre Kenné, Lucas A. Hof. 2023. « Integration of operational lockout/tagout in a joint production and maintenance policy of a smart production system ». International Journal of Production Economics. vol. 263
Chahine Ghimouz, Jean-Pierre Kenné, Lucas A. Hof. 2023. « On sustainable design and manufacturing for the footwear industry – Towards circular manufacturing ». Materials and Design. vol. 233
Nooshin Ghodsian, Khaled Benfriha, Adel Olabi, Varun Gopinath, Esma Talhi, Lucas A. Hof, Aurélien Arnou. 2023. « A framework to integrate mobile manipulators as cyber–physical systems into existing production systems in the context of industry 4.0 ». Robotics and Autonomous Systems. vol. 169
Soroosh Hakimian, Shamim Pourrahimi, Abdel-Hakim Bouzid, Lucas A. Hof. 2023. « Application of machine learning for the classification of corrosion behavior in different environments for material selection of stainless steels ». Computational Materials Science. vol. 228
Mohammad Maroufkhani, Soorosh Hakimian, Alireza Khodabandeh, Iulian Radu, Lucas A. Hof, Mohammad Jahazi. 2023. « Influence of oxygen content in the protective gas on pitting corrosion resistance of a 316l stainless steel weld joint ». Materials. vol. 16 , nº 17.
Camilo Mejía-Moncayo, Jean-Pierre Kenné, Lucas A. Hof. 2023. « On the development of a smart architecture for a sustainable manufacturing-remanufacturing system: A literature review approach ». Computers and Industrial Engineering. vol. 180
D. E. Ondze Gazani, S. Nadeau, L. Hof. 2023. « Mise en service des lunettes intelligentes pour l’assemblage ou le désassemblage ». 43e congrès de l’AQHSST (Trois-Rivières, QC, Canada, 10-12 mai 2023)
Shamim Pourrahimi, Soroosh Hakimian, Abdel-Hakim Bouzid, Lucas A. Hof. 2023. « On the use of machine learning algorithms to predict the corrosion behavior of stainless steels in lactic acid ». Metals. vol. 13 , nº 8.
Maroua Raya, Ali Aidibe, Sylvie Nadeau, Lucas Hof, Hany Moustapha. 2023. « Livre blanc Réseau SDG Innovation: Au delà de l’industrie 4.0/5.0 : Vers une société Smart Digital Green ». (Montréal, QC, Canada : 9 nov. 2022). 60 p.
Erika Villalobos, Tasseda Boukherroub, Lucas Hof, Neila El-Asli. 2023. « Economic feasibility analysis of a medical mask closed-loop supply chain: A Canadian case study ». CIGI Qualita MOSIM : Propulser la performance - Interconnectivité et collaboration dans un contexte d'intelligence artificielle (Trois-Rivières, QC, Canada, June 14-16, 2023)
Guillaume Villeneuve, Lucas A. Hof. 2023. « On the use of the current signal in spark assisted chemical engraving for micromachining process control ». Precision Engineering. vol. 83 p. 181-191.
P. H. C. Rocha, S. Langlois, S. Lalonde, J. A. Araujo, F. C. Castro. 2023. « Influence of 1350 and 6201 aluminum alloys on the fatigue life of overhead conductors – A finite element analysis ». Tribology International. vol. 186
Mohammed Alkhabbat, François Nadeau, Fatemeh Mirakhorli, Thien-My Dao, Xuan Tan Pham. 2023. « Effect of laser welding parameters with different fillers on solidification cracking and mechanical properties of AA7075 ». Metals. vol. 13 , nº 10.
Mohammad E. Bajgholi, Gilles Rousseau, Edward Ginzel, Denis Thibault, Martin Viens. 2023. « Total focusing method applied to probability of detection ». International Journal of Advanced Manufacturing Technology. vol. 126 , nº 7-8. p. 3637-3647.
Mohammad Ebrahim Bajgholi, Gilles Rousseau, Martin Viens, Denis Thibault. 2023. « Advanced ultrasonic inspection methodologies for fitness-for-service (F.F.S) assessment of hydraulic turbines ». International Journal of Advanced Manufacturing Technology. vol. 129 , nº 5-6. p. 2621-2633.
Mohammad Ebrahim Bajgholi, Gilles Rousseau, Martin Viens, Denis Thibault, Martin Gagnon. 2023. « Reliability assessment of non-destructive testing (NDT) for the inspection of weld joints in the hydroelectric turbine industry ». International Journal of Advanced Manufacturing Technology. vol. 128 , nº 9-10. p. 4223-4233.
Sevan Bouchy, Ricardo J. Zednik, Pierre Belanger. 2022. « Characterization of the elastic, piezoelectric, and dielectric properties of lithium niobate from 25 degrees C to 900 degrees C using electrochemical impedance spectroscopy resonance method ». Materials. vol. 15 , nº 13.
Aubin A. Chaboty, Vu-Hieu Nguyen, Salah Naili, Guillaume Haiat, Pierre Bélanger. 2022. « Effect of bone degradation on axially transmitted low frequency (<500 kHz) ultrasonic guided waves ». Journal of the Acoustical Society of America. vol. 152 , nº 4_Suppl.. p. A281.
Frederic Dupont-Marillia, Joseph Krynicki, Pierre Bélanger. 2022. « Early detection of high temperature hydrogen attack using the ultrasonic full matrix capture and advanced post-processing methods ». NDT and E International. vol. 130
Baptiste Gauthier, Guillaume Painchaud-April, Alain Le Duff, Pierre Belanger. 2022. « Lightweight and amplitude-free ultrasonic imaging using single-bit digitization and instantaneous phase coherence ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 69 , nº 5. p. 1763-1774.
Daniel Pereira, Alain Le Duff, Guillaume Painchaud-April, Pierre Belanger. 2022. « Simulation-based inversion for the characterization of adhesively bonded joints using ultrasonic guided waves ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 69 , nº 7. p. 2400-2407.
Lucas Pereira Piedade, Guillaume Painchaud-April, Alain Le Duff, Pierre Bélanger. 2022. « Minimum transmission events for fast ultrasonic TFM imaging: A comparative study ». NDT and E International. vol. 128 14 p.
Aurelien Thon, Guillaume Painchaud-April, Alain Le Duff, Pierre Bélanger. 2022. « Optimization of a Lorentz forces EMAT for the reconstruction of the circumferential thickness profile of a steel pipe using high order shear horizontal modes ». NDT and E International. vol. 128
Gregory Giard, Maxime Tousignant, Kevin McMeekin, Federico Bellotto, Philippe Bocher, Frederic Sirois. 2022. « Power-equivalent complex permeability model for nonlinear and hysteretic materials in the frequency domain for induction heating applications ». IEEE Transactions on Magnetics. vol. 58 , nº 6.
Ali Kalush, Damien Texier, Maxime Ecochard, Quentin Sirvin, Karim Choquet, Thomas Gheno, Nicolas Vanderesse, Walid Jomaa, Philippe Bocher. 2022. « Size effects on high temperature oxidation of MCrAlY coatings processed via APS and HVOF depositions ». Surface and Coatings Technology. vol. 440
Mahdi Masoumi Khalilabad, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher. 2022. « Effect of heat treatments on microstructural and mechanical characteristics of dissimilar friction stir welded 2198/2024 aluminum alloys ». Journal of Adhesion Science and Technology. vol. 36 , nº 3. p. 221-239.
Fateh Slamani, Denis Thibault, Yves Verreman, Philippe Bocher. 2022. « A new morphology of retained austenite obtained by intercritical tempering of 13Cr-4Ni martensitic stainless steel ». Materials Characterization. vol. 193
Nicolas Vanderesse, Philippe Bocher, Natalia Nuño, Alejandro Yánez, Lucas A. Hof. 2022. « On the characterization of roughness and geometrical irregularities of additively manufactured single titanium-alloy struts ». Additive Manufacturing. vol. 54
P. A. Deschênes, R. Wheeler, D. Paquet, J. Lanteigne, A. M. Serventi, L. Tôn-Thât, H. Champliaud. 2022. « Micromechanical properties of low-carbon martensitic stainless steel by microtensile experiments ». Materials Science and Engineering: A. vol. 858
Simin Dourandish, Henri Champliaud, Jean -Benoit Morin, Mohammad Jahazi. 2022. « Microstructure-based finite element modeling of a martensitic stainless steel during hot forging ». International Journal of Advanced Manufacturing Technology. vol. 123 , nº 7-8. p. 2833-2851.
Minh-Nha Pham, Henri Champliaud, Zhaoheng Liu, Ilian A. Bonev. 2022. « Parameterized finite element modeling and experimental modal testing for vibration analysis of an industrial hexapod for machining ». Mechanism and Machine Theory. vol. 167 23 p.
Ali Vedaei-Sabegh, Jean-Benoît Morin, Henri Champliaud, Mohammad Jahazi. 2022. « Influence of thermally grown oxides on interfacial friction during hot deformation of large-size forging ingots ». Journal of Materials Research and Technology. vol. 21 p. 3412-3424.
Ali Yalpanian, Raynald Guilbault. 2022. « A fast thermoelastic model based on the half-space theory applied to elastohydrodynamic lubrication of line contacts involving free boundaries ». Journal of Tribology. vol. 144 , nº 8.
Victor Delpla, Kevin Chapron, Jean-Pierre Kenne, Lucas Hof. 2022. « Towards intelligent manufacturing system safety strategies: generating LockOut/TagOut sheets by Machine Learning - a case study ». IFAC-PapersOnLine. vol. 55 , nº 10. p. 1001-1006.
Victor Delpla, Jean-Pierre Kenné, Lucas A. Hof. 2022. « Circular manufacturing 4.0: Towards internet of things embedded closed-loop supply chains ». The International Journal of Advanced Manufacturing Technology. vol. 118 p. 3241-3264.
Mathieu Grange, Sylvie Nadeau, Lucas Hof. 2022-11-02. « Disassembly 4.0/5.0 in the Automotive Industry ». Substance ÉTS. vol.
Mathieu Grange, Sylvie Nadeau, Lucas Hof. 2022-11-02. « Désassemblage 4.0/5.0 : le cas de l’industrie automobile ». Substance ÉTS. vol.
Soorosh Hakimian, Hakim A. Bouzid, Lucas Hof. 2022. « A study on the influence of operational factors on the flange face corrosion using a novel experimental test bench ». Communication lors de la conférence : ASME Bolted Joint Reliability Symposium ( Houston, TX, USA, Oct. 26-27, 2022 )
Soroosh Hakimian, Lucas A. Hof, Hakim A. Bouzid. 2022. « An improved fixture to quantify corrosion in bolted flanged gasketed joints subjected to service conditions ». ASME Pressure Vessels & Piping Conference (Las Vegas, Nevada, USA, July 17-22, 2022) American Society of Mechanical Engineers (ASME).
Soroosh Hakimian, Lucas Hof, Hakim A. Bouzid. 2022. « Investigation of corrosion in bolted flanged joints using a novel experimental setup ». ECS Meeting Abstracts. vol. MA2022-01 , nº 16. p. 990.
Patrick Megoze Pongha, Jean-Pierre Kenné, Edgar De Jesus Garcia, Lucas A. Hof. 2022. « Optimal joint production, maintenance and product quality control policies for a continuously deteriorating manufacturing system ». International Journal of Modelling and Simulation. (Sous presse)
Camilo Mejia-Moncayo, Alix E. Rojas, Jean-Pierre Kenne, Lucas A. Hof. 2022. « An ant approach to define product families and remanufacturing cells ». IFAC-PapersOnLine. vol. 55 , nº 10. p. 73-78.
S. Nadeau, L. Hof, K. Landau. 2022. « Les systèmes d'assistance numérique au service de la diversité ». Communication lors de la conférence : Congrès de l'AQHSST ( Sherbrooke, QC, Canada, 11-13 mai 2022 )
Patrick Megoze Pongha, Guy-Richard Kibouka, Jean-Pierre Kenné, Lucas A. Hof. 2022. « Production, maintenance and quality inspection planning of a hybrid manufacturing/remanufacturing system under production rate-dependent deterioration ». International Journal of Advanced Manufacturing Technology. vol. 121 p. 1289-1314.
P. H. C. Rocha, S. Langlois, S. Lalonde, J. A. Araújo, F. C. Castro. 2022. « A general life estimation method for overhead conductors based on fretting fatigue behavior of wires ». Theoretical and Applied Fracture Mechanics. vol. 121
P. H. C. Rocha, S. Langlois, S. Lalonde, J. A. Araujo, F. C. Castro. 2022. « Life prediction of an ACSR conductor based on the similitude with fretting fatigue tests on wires ». Communication lors de la conférence : 10th International Symposium on Fretting Fatigue (ISFF10) ( Louvain, Belgique, Sept. 19-21, 2022 )
Thi-Thuyet Bui, Viet-Hung Vu, Zhaoheng Liu. 2022. « Modal analysis of slow varying non-stationary vibration by model updating with Schur complement ». Mechanical Systems and Signal Processing. vol. 162 15 p.
Thanh-Trung Do, Viet-Hung Vu, Zhaoheng Liu. 2022. « Linearization of dynamic equations for vibration and modal analysis of flexible joint manipulators ». Mechanism and Machine Theory. vol. 167
Antoine Proteau, Ryad Zemouri, Antoine Tahan, Marc Thomas, Wafa Bounouara, Stéphane Agnard. 2022. « CNC machining quality prediction using variational autoencoder: A novel industrial 2 TB dataset ». Prognostics and Health Management Conference (PHM-2022 London) (London, UK, May 27-29, 2022) p. 360-367. Piscataway, NJ, USA : IEEE.
Edward Ginzel, Mohammad E. Bajgholi, Mariana Burrowes M. Guimarâes, Fabrice Foucher, Gilles Rousseau, Martin Viens. 2022. « Total focusing method used for flaw sizing in probability of detection determination ». e-Journal of Nondestructive Testing. vol. 27 , nº 7.
H. Shahmiri, M. Viens. 2022. « Nondestructive evaluation of electroplating-induced hydrogen embrittlement in cadmium-coated high-strength steel using ultrasonic surface waves ». Materials Evaluation. vol. 79 , nº 11. p. 1094-1104.
Aubin Chaboty, Frédéric Dupont-Marillia, Pierre Bélanger. 2021. « Propagation of low frequency ultrasonic guided waves through welded lap joint ». Journal of Nondestructive Evaluation. vol. 40 , nº 2.
Arthur Chapon, Daniel Pereira, Matthew Toews, Pierre Belanger. 2021. « Deconvolution of ultrasonic signals using a convolutional neural network ». Ultrasonics. vol. 111
Frederic Dupont-Marillia, Mohammad Jahazi, Pierre Belanger. 2021. « Phased array probe for the inspection of large steel forgings ». Cogent Engineering. vol. 8 , nº 1.
Jorge Franklin Mansur Rodrigues Filho, Pierre Bélanger. 2021. « Probe standoff optimization method for phased array ultrasonic TFM imaging of curved parts ». Sensors. vol. 21 , nº 19. 16 p.
Baptiste Gauthier, Guillaume Painchaind-April, Alain Le Duff, Pierre Bélanger. 2021. « Performances evaluation of instantaneous frequency imaging for specular reflectors and multi-view ultrasonic inspection ». Communication lors de la conférence : 48th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) ( En ligne, July 28-30, 2021 )
Baptiste Gauthier, Guillaume Painchaud-April, Alain Le Duff, Pierre Bélanger. 2021. « Towards an alternative to time of flight diffraction using instantaneous phase coherence imaging for characterization of crack-like defects ». Sensors. vol. 21 , nº 3. 18 p.
Shreyank Gupta, Guillame Haiat, Catherine Laporte, Pierre Belanger. 2021. « Effect of the acoustic impedance mismatch at the bone-soft tissue interface as a function of frequency in transcranial ultrasound: A simulation and in-vitro experimental study ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 68 , nº 5. p. 1653-1663.
Yunsang Kwak, Vu-Hieu Nguyen, Yoann Hériveaux, Pierre Belanger, Junhong Park, Guillaume Haïat. 2021. « Ultrasonic assessment of osseointegration phenomena at the bone-implant interface using convolutional neural network ». Journal of the Acoustical Society of America. vol. 149 , nº 6. p. 4337-4347.
Thibault Latête, Baptiste Gauthier, Pierre Belanger. 2021. « Towards using convolutional neural network to locate, identify and size defects in phased array ultrasonic testing ». Ultrasonics. vol. 115 9 p.
Lucas Pereira Piedade, Guillaume Painchaind-April, Alain Le Duff, Pierre Bélanger. 2021. « Minimum transmission events for fast ultrasonic imaging using sparse-TFM approaches ». Communication lors de la conférence : 48th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) ( En ligne, July 28-30, 2021 )
Jorge Franklin Mansur Rodrigues Filho, Pierre Bélanger. 2021. « Improved ultrasonic phased array transmission through concave surfaces ». Communication lors de la conférence : 48th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) ( En ligne, July 28-30, 2021 )
Aurelien Thon, Alain Le Duff, Guillaume Painchaind-April, Pierre Bélanger. 2021. « Reconstruction of the remnant thickness circumferential profile of a steel pipe using high order shear horizontal waves and emats ». Communication lors de la conférence : 48th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) ( En ligne, July 28-30. 2021 )
Bhupesh Verma, Jorge Franklin Mansur Rodrigues Filho, Pierre Bélanger. 2021. « Rayleigh wave excitation method using ultrasonic phased arrays for the detection of surface cracks ». Communication lors de la conférence : 48th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) ( En ligne, July 28-30, 2021 )
Florent Bridier, Philippe Bocher, Jonathan Cormier, Patrick Villechaise. 2021-10-05. « Method for heat treating by induction an alloy component for generating microstructure gradients and an alloy component heat treated according to the method ».
Fayaz Foroozmehr, Philippe Bocher. 2021. « An investigation on fracture toughness of the heat-affected zone in the welded joints of 13% Cr-4% Ni martensitic stainless steels ». Fatigue & Fracture of Engineering Materials & Structures. vol. 44 , nº 12. p. 3416-3430.
E. J. Herrera-Jimenez, N. Vanderesse, E. Bousser, T. Schmitt, P. Bocher, L. Martinu, J. E. Klemberg-Sapieha. 2021. « Fracture mechanism of TiN coatings on Ti-6Al-4V substrates : Role of interfaces and of the residual stress depth profile ». Surface and Coatings Technology. vol. 426 12 p.
Pierre Maurel, Laurent Weiss, Philippe Bocher, Thierry Grosdidier. 2021. « Effects of SMAT at cryogenic and room temperatures on the kink band and martensite formations with associated fatigue resistance in a β-metastable titanium alloy ». Materials Science and Engineering A. vol. 803 11 p.
Samuel Milton, Olivier Rigo, Sebastien LeCorre, Antoine Morandeau, Raveendra Siriki, Philippe Bocher, Rene Leroy. 2021. « Microstructure effects on the machinability behaviour of Ti6Al4V produced by Selective Laser Melting and Electron Beam Melting process ». Materials Science and Engineering A. vol. 823 12 p.
Thomas Perard, Alexey Sova, Hugo Robe, Vincent Robin, Yasser Zedan, Philippe Bocher, Eric Feulvarch. 2021. « Friction stir processing of austenitic stainless steel cold spray coating deposited on 304L stainless steel substrate: Feasibility study ». International Journal of Advanced Manufacturing Technology. vol. 115 , nº 7-8. p. 2379-2393.
Y. Zedan, M. Iben Houria, N. Vanderesse, F. Atmani, F. Mirakhorli, F. Nadeau, V. Demers, P. Bocher. 2021. « Fatigue properties of continuous wave and pulsed wave laser cold-wire welding of thick section AA6005-T6 aluminum alloys ». International Journal of Fatigue. vol. 147 13 p.
Yassine Bouissa, Muftah Zorgani, Davood Shahriari, Henri Champliaud, Jean-Benoît Morin, Mohammad Jahazi. 2021. « Microstructure-based FEM modeling of phase transformation during quenching of large-size steel forgings ». Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. vol. 52 , nº 5. p. 1883-1900.
Samuel Brodeur, Van Ngan Le, Henri Champliaud. 2021. « A nonlinear finite-element analysis tool to prevent rupture of power transformer tank ». Sustainability. vol. 13 , nº 3. 16 p.
P. Y. Paradis, H. Champliaud. 2021. « New correlations for heat transfer in parallel-plate ducts at low Peclet number ». International Journal of Heat and Mass Transfer. vol. 178 11 p.
Charles Aboussafy, Raynald Guilbault. 2021. « Chip formation in machining of anisotropic plastic materialsa finite element modeling strategy applied to wood ». International Journal of Advanced Manufacturing Technology. vol. 114 , nº 5/6. p. 1471-1486.
Raynald Guilbault, Sébastien Lalonde. 2021. « Tip relief designed to optimize contact fatigue life of spur gears using adapted PSO and firefly algorithms ». SN Applied Sciences. vol. 3 , nº 1.
Ali Yalpanian, Raynald Guilbault. 2021. « A systematic solution based on the half-space concept for modeling of thermoelastic contact between bodies defined by curved free boundaries ». Acta Mechanica. vol. 232 p. 5003-5029.
Victor Delpla, Jean-Pierre Kenné, Ameth Maloum Fall, Mahan Balalpour, Lucas A. Hof. 2021. « Metal scrap recycling 4.0: Towards smart operation and production of high-quality alloys ». Canadian Society for Mechanical Engineering International Congress (2021) (Charlottetown, PE, Canada, June 28-30, 2021) Charlottetown, P.E.I. : University of Prince Edward Island. Robertson Library.
Panteha Fallah, Lucas A. Hof, Rolf Wuthrich. 2021. « Fabrication of high-thickness and low surface roughness metal parts by a hybrid electrochemical manufacturing process ». Advances in Industrial and Manufacturing Engineering. vol. 2 6 p.
Lucas Hof. 2021. « Cirdular Manufacturing 4.0 ». In 2021 World Manufacturing Report: Digitally Enabled Circular Manufacturing . p. 19. World Manufacturing Foundation.
Lucas Hof. 2021. « Digital entreprises - a new educative learning program for students and professionals ». Communication lors de la conférence : Mardi 4.0 - seminar series "Reseau Innovation 4.0 Network" ( Montréal, QC, Canada, )
Lucas Abia Hof, Rolf Wuthrich. 2021. « Glass precision micro-cutting using spark assisted chemical engraving ». Advances in Industrial and Manufacturing Engineering. vol. 3
Jean-Philippe Leclair, Newton Borges, Duncan Cree, Lucas A. Hof. 2021. « Towards circular manufacturing: Repurposing eggshell waste as filler for poly lactic acid feedstock for 3D printing ». Canadian Society for Mechanical Engineering International Congress (2021) (Charlottetown, PE, Canada, June 28-30, 2021) Charlottetown, P.E.I. : University of Prince Edward Island. Robertson Library.
Camilo Mejía-Moncayo, Jean-Pierre Kenné, Lucas A. Hof. 2021. « A hybrid architecture for a reconfigurable cellular remanufacturing system ». Advances in Production Management Systems. Artificial Intelligence for Sustainable and Resilient Production Systems : IFIP WG 5.7 International Conference on Advances in Production Management Systems, APMS 2021, Proceedings, Part I (Nantes, France, Sept. 05-09, 2021) p. 488-496. Springer.
S. Nadeau, R. Bruder, L. Hof. 2021. « Using Smart Glasses in assembly/disassembly: Current state of the art ». Travail et Santé. vol. 37 , nº 2. p. 2-6.
Jacopo Profili, Rafael Brunet, Émilie L. Dubois, Vincent Groenhuis, Lucas A. Hof. 2021. « Use of 3D printed connectors to redesign full face snorkeling masks in the COVID-19 era: A preliminary technical case-study ». Annals of 3D Printed Medicine. vol. 3
Jacopo Profili, Emilie L. Dubois, Dimitrios Karakitsos, Lucas A. Hof. 2021. « Overview of the user experience for snorkeling mask designs during the COVID-19 pandemic ». Healthcare. vol. 9 , nº 2. 19 p.
Amine Omrani, Sebastien Langlois, Pierre Van Dyke, Sebastien Lalonde, Sasan Sattarpanah Karganroudi, Lamine Dieng. 2021. « Fretting fatigue life assessment of overhead conductors using a clamp/conductor numerical model and biaxial fretting fatigue tests on individual wires ». Fatigue and Fracture of Engineering Materials and Structures. vol. 44 , nº 6. p. 1498-1514.
Thanh-Trung Do, Viet-Hung Vu, Zhaoheng Liu. 2021. « Symbolic differentiation algorithm for inverse dynamics of serial robots with flexible joints ». Journal of Mechanisms and Robotics. vol. 13 , nº 6. 8 p.
Minh-Nha Pham, Bruce Hazel, Philippe Hamelin, Zhaoheng Liu. 2021. « Vibration control of flexible joint robots using a discrete-time two-stage controller based on time-varying input shaping and delay compensation ». Journal of Dynamic Systems Measurement and Control. vol. 143 , nº 10. 18 p.
Mohammad Ebrahim Bajgholi, Gilles Rousseau, Martin Viens, Denis Thibault. 2021. « Capability of advanced ultrasonic inspection technologies for hydraulic turbine runners ». Applied Sciences. vol. 11 , nº 10. 15 p.
Guillaume Boivin, Pierre Bélanger, Ricardo J. Zednik. 2020. « Characterization of pure face-shear strain in piezoelectric alpha-tellurium dioxide (alpha-TeO2) ». Crystals. vol. 10 , nº 10. 9 p.
Jawad Dahmani, Catherine Laporte, Daniel Pereira, Pierre Bélanger, Yvan Petit. 2020. « Predictive model for designing soft-tissue mimicking ultrasound phantoms with adjustable elasticity ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 67 , nº 4. p. 715-726.
Daniel Pereira, Julio Fernandes, Pierre Belanger. 2020. « Ex vivo assessment of cortical bone properties using low-frequency ultrasonic guided waves ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 67 , nº 5. p. 910-922.
Geoffrey Veit, Pierre Bélanger. 2020. « An ultrasonic guided wave excitation method at constant phase velocity using ultrasonic phased array probes ». Ultrasonics. vol. 102 9 p.
J. Ajaja, W. Jomaa, P. Bocher, R. R. Chromik, M. Brochu. 2020. « High cycle fatigue behavior of hard turned 300 M ultra-high strength steel ». International Journal of Fatigue. vol. 131
Amrita Bag, Dorian Delbergue, Jihane Ajaja, Philippe Bocher, Martin Lévesque, Myriam Brochu. 2020. « Effect of different shot peening conditions on the fatigue life of 300M steel submitted to high stress amplitudes ». International Journal of Fatigue. vol. 130 12 p.
Quentin Boyadjian, Nicolas Vanderesse, Matthew Toews, Philippe Bocher. 2020. « Detecting defects in materials using deep convolutional neural networks ». Image Analysis and Recognition : 17th International Conference, ICIAR 2020, Póvoa de Varzim, Portugal, June 24–26, 2020, Proceedings, Part I (Póvoa de Varzim, Portugal, June 24-26, 2020) p. 293-306. Springer.
R. Bretin, M. Levesque, P. Pilvin, P. Bocher. 2020. « Neighborhood effect within polycrystalline materials: Elastoplastic micromechanical analysis by cellular automaton and finite element ». International Journal of Fatigue. vol. 137 16 p.
Kanwal Chadha, Yuan Tian, Philippe Bocher, John G. Spray, Clodualdo Aranas. 2020. « Microstructure evolution, mechanical properties and deformation behavior of an additively manufactured maraging steel ». Materials. vol. 13 , nº 10. 16 p.
Clément Dureau, Marc Novelli, Mandana Arzaghi, Roxane Massion, Philippe Bocher, Yves Nadot, Thierry Grosdidier. 2020. « On the influence of ultrasonic surface mechanical attrition treatment (SMAT) on the fatigue behavior of the 304L austenitic stainless steel ». Metals. vol. 10 , nº 1. 14 p.
Fayaz Foroozmehr, Philippe Bocher. 2020. « Effect of low temperature intercritical heat-treatment on stable crack growth behavior in 13% Cr-4% Ni martensitic stainless steel multipass weldments ». Engineering Fracture Mechanics. vol. 240
Fayaz Foroozmehr, Philippe Bocher. 2020. « On the ductile rupture of 13% Cr-4% Ni martensitic stainless steels ». International Journal of Fracture. vol. 224 , nº 1. p. 67-82.
Stéphane Godin, Johann Hamel-Akré, Denis Thibault, Alessandra-Maria Serventi, Philippe Bocher. 2020. « Ni and Mn enrichment effects on reformed austenite: thermodynamical and low cycle fatigue stability of 13%Cr–4%Ni and 13%Cr–6%Ni stainless steels ». SN Applied Sciences. vol. 2 , nº 3.
Mahdi Jamshidinia, Hadi Ghasemi-Nanesa, Philippe Bocher, Natalia Nuno, Behrang Poorganji, Mahdi Habibnejad-Korayem. 2020. « Microstructural alteration of alloyed steel in direct metal laser melting by powder bed deposition system ». Steel Research International. vol. 91 , nº 10. 7 p.
Pierre Maurel, Laurent Weiss, Philippe Bocher, Eric Fleury, Thierry Grosdidier. 2020. « Mechanisms of oxide dependent tribological behavior in Ti / Steel sliding and influence of nanostructured surfaces ». 14th World Conference on Titanium (Ti 2019) (Nantes, France, June 10-14, 2020) EDP Sciences.
Pierre Maurel, Laurent Weiss, Thierry Grosdidier, Philippe Bocher. 2020. « How does surface integrity of nanostructured surfaces induced by severe plastic deformation influence fatigue behaviors of Al alloys with enhanced precipitation? ». International Journal of Fatigue. vol. 140 12 p.
Yousef Saadati, Jean-François Chatelain, Gilbert Lebrun, Yves Beauchamp, Philippe Bocher, Nicolas Vanderesse. 2020. « A study of the interlaminar fracture toughness of unidirectional flax/epoxy composites ». Journal of Composites Science. vol. 4 , nº 2.
I. Tabiai, D. Texier, P. Bocher, D. Therriault, M. Levesque. 2020. « In-situ full field out of plane displacement and strain measurements at the micro-scale in single reinforcement composites under transverse load ». Experimental Mechanics. vol. 60 , nº 3. p. 359-377.
Lofti Toubal, Hamed Chaabouni, Philippe Bocher, Chen Jianqiang. 2020. « Monitoring fracture of high-strength steel under tensile and constant loading using acoustic emission analysis ». Engineering Failure Analysis. vol. 108
N. Vanderesse, D. Texier, P. Bocher. 2020. « Effect of porosities on brazed martensitic steel tensile properties: 2D and 3D pre-mortem vs post-mortem characterizations ». Materials Characterization. vol. 160 14 p.
Y. Bouissa, N. Bohlooli, D. Shahriari, H. Champliaud, J. B. Morin, M. Jahazi. 2020. « FEM modeling and experimental validation of quench-induced distortions of large size steel forgings ». Journal of Manufacturing Processes. vol. 58 p. 592-605.
J. B. Lévesque, J. Lanteigne, H. Champliaud, D. Paquet. 2020. « Modeling solid-state phase transformations of 13Cr-4Ni steels in welding heat-affected zone ». Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. vol. 51 , nº 3. p. 1208-1220.
Huy Hoan Nguyen, Henri Champliaud, Van Ngan Lê. 2020. « Circumferential cracking in conventional metal spinning process ». 32nd European Modeling and Simulation Symposium (EMSS) (En ligne, Sept. 16-18, 2020) p. 165-170. Dime University of Genoa.
Sheida Sarafan, Priti Wanjara, Jean-Benoit Levesque, Javad Gholipour, Henri Champliaud, Louis Mathieu. 2020. « Through-thickness residual stresses, microstructure, and mechanical properties of electron beam-welded CA6NM martensitic stainless steel after postweld heat treatment ». Advances in Materials Science and Engineering. vol. 2020 16 p.
Ali Yalpanian, Raynald Guilbault. 2020. « A fast correction for half-space theory applied to contact modeling of bodies with curved free surfaces ». Tribology International. vol. 147 13 p.
Zahra Chaghazardi, Lucas Hof, Rolf Wuthrich. 2020. « Electropolishing of inside surfaces of stainless steel tubing ». ECS Transactions. vol. 97 , nº 7. p. 523-536.
Victor Delpla, Lucas A. Hof, Jean-Pierre Kenné. 2020. « Closed loop supply chain optimization for Circular Manufacturing using Industry 4.0 technologies ». 8th International Conference on Information Systems, Logistics and Supply Chain: Interconnected Supply Chains in an Era of Innovation (ILS) (Austin, TX, USA, Apr. 22-24, 2020) p. 220-227. International Conference on Information Systems, Logistics and Supply Chain.
Pantea Koushki, Tsz-Ho Kwok, Lucas Hof, Rolf Wuthrich. 2020. « Reinforcing silicone with hemp fiber for additive manufacturing ». Composites Science and Technology. vol. 194 p. 141-151.
Daxian Hao, Wei Wang, Zhaoheng Liu, Chao Yun. 2020. « Experimental study of stability prediction for high-speed robotic milling of aluminum ». Journal of Vibration and Control. vol. 26 , nº 7/8. p. 387-398.
HtunHtun Oo, Wei Wang, Zhaoheng Liu. 2020. « Tool wear monitoring system in belt grinding based on image-processing techniques ». International Journal of Advanced Manufacturing Technology. vol. 111 , nº 7-8. p. 2215-2229.
Minh-Nha Pham, Philippe Hamelin, Bruce Hazel, Zhaoheng Liu. 2020. « A two-stage state feedback controller supported by disturbance-state observer for vibration control of a flexible-joint robot ». Robotica. vol. 38 , nº 6. p. 1082-1104.
Kanglin Xing, Xiaojie Liu, Zhaoheng Liu, J. R. R. Mayer, Sofiane Achiche. 2020. « Low-cost precision monitoring system of machine tools for SMEs ». 8th CIRP Global Web Conference – Flexible Mass Customisation (CIRPe 2020) (Leuven, Belgium, Oct. 14-16, 2020) p. 347-352. Elsevier.
Alireza Aleyari, Omid Majidi, Nicolas Bombardier, Xuan-Tan Pham, Mohammad Jahazi. 2020. « Finite element and experimental analysis of the preheating stage of High Speed Blow Forming (HSBF) process ». Journal of Manufacturing Processes. vol. 49 p. 10-17.
Olivier Champagne, Xuan-Tan Pham. 2020. « Numerical simulation of moving heat source in arc welding using the Element-free Galerkin method with experimental validation and numerical study ». International Journal of Heat and Mass Transfer. vol. 154 8 p.
Dinh-Dong Dang, Xuan-Tan Pham, Chi-Cong Nguyen. 2020. « Thermal performance prediction in the air gap of a rotor-stator configuration: effects of numerical models ». Journal of Thermal Science and Engineering Applications. vol. 29 , nº 1. p. 206-218.
Antoine Proteau, Ryad Zemouri, Antoine Tahan, Marc Thomas. 2020. « Dimension reduction and 2D-visualization for early change of state detection in a machining process with a variational autoencoder approach ». International Journal of Advanced Manufacturing Technology. vol. 111 , nº 11-12. p. 3597-3611.
Marc Thomas. 2020. « Vibrations mécaniques : Recueil d'exercices et corrigés ». Montréal ; Québec : ÉTS ; Presses de l'Université du Québec. 578 p.
Mohammad E. Bajgholi, Gilles Rousseau, Martin Viens, Denis Thibault. 2020. « Performance of Ultrasonic Inspection on hydroelectric turbine runner ». Communication lors de la conférence : 3rd International Symposium on Structural Health Monitoring and Nondestructive Testing ( Québec, QC, Canada, Nov. 25-26, 2020 )
Ehsan Mohseni, Hamid Habibzadeh Boukani, Demartonne Ramos Franca, Martin Viens. 2020. « A study of the automated eddy current detection of cracks in steel plates ». Journal of Nondestructive Evaluation. vol. 39 , nº 1. 12 p.
Ehsan Mohseni, Demartonne Ramos Franca, Martin Viens, Wen Fang Xie, Baoguang Xu. 2020. « Finite element modelling of a reflection differential split-D eddy current probe scanning surface notches ». Journal of Nondestructive Evaluation. vol. 39 , nº 2.
Ehsan Mohseni, Martin Viens, Wen-Fang Xie. 2020. « Adaptive neuro-fuzzy inference system trained for sizing semi-elliptical notches scanned by eddy currents ». Journal of Nondestructive Evaluation. vol. 39 , nº 1.
Konstantin Polyakov, Fernando López, Martin Viens. 2020. « Advanced signal processing techniques to improve the detection of defects in pressure vessels by acoustic emission testing ». The e-Journal of Nondestructive Testing. vol. 25 , nº 12. 2 p.
Pierre Belanger, Mohammad Jahazi. 2019. « Friction stir welded lap joint inspection using ultrasonic guided waves ». 45th Annual Review of Progress in Quantitative Nondestructive Evaluation, Volume 38 (Burlington, VT, USA, July 15-19, 2018) USA : AIP Publishing.
Hector de Castilla, Pierre Bélanger, Ricardo J. Zednik. 2019. « Generalized dynamic analytical model of piezoelectric materials for characterization using electrical impedance spectroscopy ». Materials. vol. 12 , nº 16. 12 p.
Frederic Dupont-Marillia, Mohammad Jahazi, Serge Lafreniere, Pierre Belanger. 2019. « Design and optimisation of a phased array transducer for ultrasonic inspection of large forged steel ingots ». NDT and E International. vol. 103 p. 119-129.
Frederic Dupont-Marillia, Mohammad Jahazi, Serge Lafreniere, Pierre Belanger. 2019. « Influence of local mechanical parameters on ultrasonic wave propagation in large forged steel ingots ». Journal of Nondestructive Evaluation. vol. 38 , nº 3. 9 p.
D. Lemonnier, J. M. Mac-Thiong, P. Belanger. 2019. « Transverse spinal cord blood vessels visualization in a pig using plane wave doppler ultrasound imaging ». Acta Acustica United with Acustica. vol. 105 , nº 6. p. 1278-1282.
David Lemonnier, Jean-Marc Mac-Thiong, Pierre Belanger. 2019. « Flow quantification in a wall-less multiple flow phantom using ultrasound plane wave doppler imaging ». Acta Acustica united with Acustica. vol. 105 , nº 1. p. 130-138.
Daniel Pereira, Pierre Belanger. 2019. « Inverse characterization of adhesive shear modulus in bonded stiffeners using ultrasonic guided waves ». 45th Annual Review of Progress in Quantitative Nondestructive Evaluation, Volume 38 (Burlington, VT, USA, July 15-19, 2018) USA : AIP Publishing.
Daniel Pereira, Guillaume Haiat, Julio Fernandes, Pierre Belanger. 2019. « Effect of intracortical bone properties on the phase velocity and cut-off frequency of low-frequency guided wave modes (20-85 kHz) ». Journal of the Acoustical Society of America. vol. 145 , nº 1. p. 121-130.
Aurélien Thon, Pierre Bélanger. 2019. « EMAT design for minimum remnant thickness gauging using high order shear horizontal modes ». Ultrasonics. vol. 95 p. 70-78.
Nicolas Tremblay, Baptiste Gauthier, Pierre Belanger. 2019. « Feasibility of structural health monitoring in a composite plate using omnidirectional SH0 transduction ». 45th Annual Review of Progress in Quantitative Nondestructive Evaluation, Volume 38 (Burlington, VT, USA, July 15-19, 2018) USA : AIP Publishing.
J. Ajaja, W. Jomaa, P. Bocher, R. R. Chromik, V. Songmene, M. Brochu. 2019. « Hard turning multi-performance optimization for improving the surface integrity of 300M ultra-high strength steel ». International Journal of Advanced Manufacturing Technology. vol. 104 , nº 1-4. p. 141-157.
Amrita Bag, Dorian Delbergue, Philippe Bocher, Martin Lévesque, Myriam Brochu. 2019. « Statistical analysis of high cycle fatigue life and inclusion size distribution in shot peened 300M steel ». International Journal of Fatigue. vol. 118 p. 126-138.
Rémi Bertrand, Hugo Robe, Damien Texier, Yasser Zedan, Eric Feulvarch, Philippe Bocher. 2019. « Analysis of AA2XXX/AA7XXX friction stir welds ». Journal of Materials Processing Technology. vol. 271 p. 312-324.
C. Bianchetti, D. Delbergue, Philippe Bocher, M. Levesque, M. Brochu. 2019. « Analytical fatigue life prediction of shot peened AA 7050-T7451 ». International Journal of Fatigue. vol. 118 p. 271-281.
R. Bretin, M. Levesque, P. Bocher. 2019. « Neighborhood effect on the strain distribution in linearly elastic polycrystals: Part 1 Finite element study of the interaction between grains ». International Journal of Solids and Structures. vol. 176-177 p. 36-48.
R. Bretin, M. Levesque, P. Bocher. 2019. « Neighborhood effect on the strain distribution in linearly elastic polycrystals: Part 2 - Cellular Automaton ». International Journal of Solids and Structures. vol. 176-177 p. 49-67.
Dorian Delbergue, Damien Texier, Martin Lévesque, Philippe Bocher. 2019. « Diffracting-grain identification from electron backscatter diffraction maps during residual stress measurements: a comparison between the sin2ψ and cosα methods ». Journal of Applied Crystallography. vol. 52 , nº 4. p. 828-843.
G. R. Ebrahimi, A. Momeni, H. R. Ezatpour, M. Jahazi, P. Bocher. 2019. « Dynamic recrystallization in Mone1400 Ni-Cu alloy: mechanism and role of twinning ». Materials Science and Engineering : A. vol. 744 p. 376-385.
Hamid Javadi, Walid Jomaa, Victor Songmene, Myriam Brochu, Philippe Bocher. 2019. « Inconel 718 superalloy controlled surface integrity for fatigue applications produced by precision turning ». International Journal of Precision Engineering and Manufacturing. vol. 20 , nº 8. p. 1297-1310.
Mohamed Khalifa, Noureddine Barka, Jean Brousseau, Philippe Bocher. 2019. « Optimization of the edge effect of 4340 steel specimen heated by induction process with flux concentrators using finite element axis-symmetric simulation and experimental validation ». International Journal of Advanced Manufacturing Technology. vol. 104 , nº 9-12. 9 p. p. 4549-4557.
Mohamed Khalifa, Noureddine Barka, Jean Brousseau, Philippe Bocher. 2019. « Reduction of edge effect using response surface methodology and artificial neural network modeling of a spur gear treated by induction with flux concentrators ». International Journal of Advanced Manufacturing Technology. vol. 104 , nº 1-4. p. 103-117.
Mohamed Khalifa, Noureddine Barka, Jean Brousseau, Philippe Bocher. 2019. « Sensitivity study of hardness profile of 4340 steel disc hardened by induction according to machine parameters and geometrical factors ». International Journal of Advanced Manufacturing Technology. vol. 101 , nº 1-4. p. 209-221.
J. H. Liu, N. Vanderesse, J. C. Stinville, T. M. Pollock, P. Bocher, D. Texier. 2019. « In-plane and out-of-plane deformation at the sub-grain scale in polycrystalline materials assessed by confocal microscopy ». Acta Materialia. vol. 169 p. 260-274.
Pierre Maurel, Laurent Weiss, Philippe Bocher, Eric Fleury, Thierry Grosdidier. 2019. « Oxide dependent wear mechanisms of titanium against a steel counterface: influence of SMAT nanostructured surface ». Wear. vol. 430-431 p. 245-255.
Binhan Sun, Yan Ma, Nicolas Vanderesse, Rama Srinivas Varanasi, Wenwen Song, Philippe Bocher, Dirk Ponge, Dierk Raabe. 2019. « Macroscopic to nanoscopic in situ investigation on yielding mechanisms in ultrafine grained medium Mn steels: role of the austenite-ferrite interface ». Acta Materialia. vol. 178 p. 10-25.
Kamel Touahir, Ali Bilek, Philippe Bocher, Mustapha Beldi. 2019. « Experimental and numerical analysis of the fields of the frozen stresses in an epoxy sphere using the stress-freezing method and mechanical slicing ». Journal of Materials and Engineering Structures. vol. 6 , nº 2.
Heithem Touazine, Kanwal Chadha, Mohammad Jahazi, Philippe Bocher. 2019. « Characterization of subsurface microstructural alterations induced by hard turning of Inconel 718 ». Journal of Materials Engineering and Performance. vol. 28 , nº 11. p. 7016-7024.
Yassine Bouissa, Davood Shahriari, Henri Champliaud, Mohammad Jahazi. 2019. « Prediction of heat transfer coefficient during quenching of large size forged blocks using modeling and experimental validation ». Case Studies in Thermal Engineering. vol. 13
A. Fall, H. Monajati, A. Khodabandeh, M. H. Fesharaki, H. Champliaud, M. Jahazi. 2019. « Local mechanical properties, microstructure, and microtexture in friction stir welded Ti-6Al-4V alloy ». Materials Science and Engineering: A. vol. 749 p. 166-175.
Mathieu Gendron, Bruce Hazel, Eric Boudreault, Henri Champliaud, Xuan-Tan Pham. 2019. « Coupled thermo-electromagnetic model of a new robotic high-frequency local induction heat treatment system for large steel components ». Applied Thermal Engineering. vol. 150 p. 372-385.
Sheida Sarafan, Priti Wanjara, Jean-Benoît Lévesque, Javad Gholipour, Henri Champliaud, Louis Mathieu. 2019. « Residual stresses, microstructure, and mechanical properties of EB-Welded 90-mm-Thick UNS S41500 martensitic stainless steel after PWHT ». Materials Performance and Characterization. vol. 8 , nº 4. p. 648-663.
Z. Nili Ahmadabadi, Raynald Guilbault, Frédéric Laville. 2019. « Nonlinear dynamic modeling of pneumatic nailing devices ». Mathematical and Computer Modelling of Dynamical Systems. vol. 25 , nº 2. p. 195-223.
Mohamed Benadda, Ahmed Bouzidane, Marc Thomas, Raynald Guilbault. 2019. « Dynamic behavior analysis of a rigid rotor supported by hydrostatic squeeze film dampers compensated with new electrorheological valve restrictors ». Industrial Lubrication and Tribology. vol. 72 , nº 5. p. 611-619.
Raynald Guilbault, Sébastien Lalonde. 2019. « A stochastic prediction of roughness evolution in dynamic contact modelling applied to gear mild wear and contact fatigue ». Tribology International. vol. 140
Rolf Wuthrich, Lucas A. Hof. 2019. « Low batch size production of glass products requiring micrometer precision ». IFAC-PapersOnLine. vol. 52 , nº 10. p. 319-322.
Amine Omrani, Sébastien Langlois, Pierre Van Dyke, Sasan Sattarpanah Karganroudi, Sébastien Lalonde. 2019. « Fatigue strength evaluation for individual strands of overhead conductors using a biaxial fretting fatigue test bench ». 12th International Conference on Multiaxial Fatigue and Fracture (ICMFF) (Bordeaux, France, June 24-26, 2019) EDP Sciences.
T. T. Do, V.-H. Vu, Z. Liu. 2019. « Analytical modal analysis of flexible joint manipulators ». Proceedings of the 27th CANCAM (Sherbrooke, QC, Canada, May 27-30, 2019)
Tranh-Trung Do, Viet-Hung Vu, Zhaoheng Liu. 2019. « Automatic generation of inverse dynamics for industrial robots with flexible joints using a computer algebra ». Affiche présentée lors de la conférence : Applications of Computer Algebra (ACA) ( Montréal, QC, Canada, July 16-20, 2019 )
Mourad Kedadouche, Zhaoheng Liu, Marc Thomas. 2019. « Early bearing defect detection in a noisy environment based on a method combining singular value decomposition and empirical mode decomposition ». Book of Proceedings : SURVISHNO 2019 (Lyon, France, July 8-10, 2019) p. 706-721. INSA.
Yvan Soucy, Julien Joule, Zhaoheng Liu. 2019. « Investigation of force limited vibration through testing of payloads mounted on a rover and a satellite ». Communication lors de la conférence : Spacecraft and Launch Vehicle Dynamic Environments Workshop (SCLV) ( El Segundo, CA, USA, June 4-6, 2019 )
Ngoc-Hung Vu, Xuan-Tan Pham, Vincent François, Jean-Christophe Cuillière. 2019-05-01. « Behavior Characterization of Large Dimension Composite Plate ». Substance ÉTS. vol.
Ngoc-Hung Vu, Xuan-Tan Pham, Vincent François, Jean-Christophe Cuillière. 2019-05-01. « Caractérisation du comportement d’une plaque composite de grande dimension ». Substance ÉTS. vol.
Ngoc-Hung Vu, Xuan-Tan Pham, Vincent Francois, Jean-Christophe Cuillière. 2019. « Characterization of multilayered carbon-fiber-reinforced thermoplastic composites for assembly process ». Journal of Thermoplastic Composite Materials. vol. 32 , nº 5. p. 673-689.
Ngoc-Hung Vu, Xuan-Tan Pham, Vincent François, Jean-Christophe Cuillière. 2019. « Inverse procedure for mechanical characterization of multi-layered non-rigid composite parts with applications to the assembly process ». Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. vol. 233 , nº 17. p. 6167-6176.
Fatemeh Aghazadeh, Antoine Tahan, Marc Thomas. 2019. « Tool condition monitoring method in milling process using wavelet transform and long short-term memory ». SURveillance VIbrations SHocks NOise : Book of Proceedings : SURVISHNO (Lyon, France, July 08-10, 2019) p. 153-161. INSA.
Aboubakeur Benariba, Ahmed Bouzidane, Marc Thomas. 2019. « Analytical analysis of a rigid rotor mounted on three hydrostatic pads lubricated with micropolar fluids ». Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. vol. 233 , nº 6. p. 859-869.
Antoine Proteau, Antoine Tahan, Marc Thomas. 2019. « Specific cutting energy: a physical measurement for representing tool wear ». International Journal of Advanced Manufacturing Technology. vol. 103 , nº 1-4. p. 101-110.
Antoine Proteau, Marc Thomas, Antoine Tahan. 2019. « Toward the quality prognostic of an aircraft engine workpiece in Inconel Alloy 625: case study and proposed system architecture ». SURveillance VIbrations SHocks NOise : Book of Proceedings : SURVISHNO (Lyon, France, July 08-10, 2019) p. 546-560. INSA.
Yulan Sun, Marc Thomas. 2019. « Semi-active torsional vibrations control of a rotor using a smart ER dynamic absorber ». SURveillance VIbrations SHocks NOise : Book of Proceedings : SURVISHNO (Lyon, France, July 08-10, 2019) p. 636-647. INSA.
Djamal Zarour, Marc Thomas, Salim Meziani. 2019. « Diagnosis of bearing defects by variational modes decomposition from vibratory and acoustic emission measurements ». International Journal of Vehicle Noise and Vibration. vol. 15 , nº 1. p. 21-41.
Mohammad Ebrahim Bajgholi, Martin Viens. 2019. « Evaluation of the dead zones in the welded joints of hydraulic turbine runners ». Communication lors de la conférence : NDT in Canada 2019 ( Edmonton, AB, Canada, June 18-20, 2019 )
Louis-Alexandre Généreux, Gilbert Lebrun, Martin Viens, Jean-François Chatelain. 2019. « Evaluation of machining defects in a composite laminate by combining non-destructive and tensile testing ». In Materials Design and Applications II Coll. «Advanced Structured Materials», . p. 341-362. Springer Verlag.
Ali Khademi Far, Louis-Daniel Théroux, Martin Viens, Oliver Arés, Hakim Bendada. 2019. « Non-destructive evaluation of impact damage in CFRP by means of IRT, shearography and ultrasonic testing ». Communication lors de la conférence : NDT in Canada 2019 ( Edmonton, AB, Canada, June 18-20, 2019 )
Guillaume Boivin, Martin Viens, Pierre Belanger. 2018. « Plane wave SH0 piezoceramic transduction optimized using geometrical parameters ». Sensors. vol. 18 , nº 2.
Frederic Dupont-Marillia, Mohammad Jahazi, Pierre Bélanger. 2018. « Phased array inspection of large size forged steel parts ». 44th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE 2017) (Provo, UT, USA, July 16-21, 2017) American Institute of Physics.
Timothe Falardeau, Pierre Bélanger. 2018. « Material characterization using ultrasound tomography ». 44th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE 2017) (Provo, UT, USA, July 16-21, 2017) American Institute of Physics.
Timothe Falardeau, Pierre Belanger. 2018. « Ultrasound tomography in bone mimicking phantoms: Simulations and experiments ». Journal of the Acoustical Society of America. vol. 144 , nº 5. p. 2937-2946.
Baptiste Gauthier, Aurelien Thon, Pierre Bélanger. 2018. « Comparison of a piezoceramic transducer and an EMAT for the omnidirectional transduction of SH0 ». 44th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE 2017) (Provo, UT, USA, July 16-21, 2017) American Institute of Physics.
Shreyank Gupta, Guillaume Haïat, Catherine Laporte, Pierre Belanger. 2018. « Effect of acoustic impedance mismatch between skin and bone on transcranial ultrasound transmission ». The Journal of the Acoustical Society of America. Affiche présentée lors de la conférence : 176TH Meeting of the Acoustical Society of America, 2018 Acoustics Week in Canada ( , ) p. 1747.
D. Lemonnier, J. M. Mac-Thiong, P. Bélanger. 2018. « Ultrasound plane wave doppler quantification using a wall-less spinal cord representative phantom ». Acta Acustica united with Acustica. vol. 104 , nº 1. p. 166-173.
Jianqiang Chen, Vincent Demers, Daniel P. Turner, Philippe Bocher. 2018. « Experimental investigation on high-cycle fatigue of inconel 625 superalloy brazed joints ». Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. vol. 49A , nº 4. p. 1244-1253.
James William Chuitcheu, Damien Texier, Philippe Bocher. 2018-03-13. « Determining Properties of Materials at High Temperatures ». Substance ÉTS. vol.
James William Chuitcheu, Damien Texier, Philippe Bocher. 2018-03-13. « Déterminer les propriétés des matériaux à haute température ». Substance ÉTS. vol.
James William Chuitcheu, Damien Texier, Philippe Bocher. 2018-04-04. « Hot Tensile Strength Micromachine for Aeronautics ». Substance ÉTS. vol.
James William Chuitcheu, Damien Texier, Philippe Bocher. 2018-04-04. « Une micromachine de traction à chaud pour l’aéronautique ». Substance ÉTS. vol.
Nguyen Hoa Ngan, Philippe Bocher. 2018. « Finite element analysis simulation of the effect of induction hardening on rolling contact fatigue ». Journal of Tribology. vol. 140 , nº 6.
Hamid Javadi, Walid Jomaa, Elvi Dalgaard, Myriam Brochu, Philippe Bocher. 2018. « Influence of surface residual stresses on the fatigue life and crack propagation behavior of turned Inconel 718 super-alloy ». 12th International Fatigue Congress (FATIGUE 2018) (Poitiers, France, May 27-June 1, 2018) EDP Sciences.
T. Klotz, D. Delbergue, P. Bocher, M. Levesque, M. Brochu. 2018. « Surface characteristics and fatigue behavior of shot peened Inconel 718 ». International Journal of Fatigue. vol. 110 p. 10-21.
Heli Liu, Huaiju Liu, Philippe Bocher, Caichao Zhu, Zhangdong Sun. 2018. « Effects of case hardening properties on the contact fatigue of a wind turbine gear pair ». International Journal of Mechanical Sciences. vol. 141 p. 520-527.
Mahdi Masoumi Khalilabad, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher. 2018. « Effect of tool geometry and welding speed on mechanical properties of dissimilar AA2198–AA2024 FSWed joint ». Journal of Manufacturing Processes. vol. 34, part A p. 86-95.
Faranak Nazemi, Johann Hamel-Akré, Philippe Bocher. 2018. « Modeling of cementite coarsening during tempering of low-alloyed-medium carbon steel ». Journal of Materials Science. vol. 53 , nº 8. p. 6198-6218.
M. Novelli, P. Bocher, T. Grosdidier. 2018. « Effect of cryogenic temperatures and processing parameters on gradient-structure of a stainless steel treated by ultrasonic surface mechanical attrition treatment ». Materials Characterization. vol. 139 p. 197-207.
D. Texier, F. Atmani, P. Bocher, F. Nadeau, J. Chen, Y. Zedan, N. Vanderesse, V. Demers. 2018. « Fatigue performances of FSW and GMAW aluminum alloys welded joints: Competition between microstructural and structural-contact-fretting crack initiation ». International Journal of Fatigue. vol. 116 p. 220-233.
Ehsan Tolouei, Mohammad Reza Toroghinejad, Hamed Asgari, Hossein Monajati Zadeh, Fakhreddin Ashrafizadeh, Jerzy A. Szpunar, Philippe Bocher. 2018. « Microstructure and texture development in Al-3%Brass composite produced through ARB ». Advanced Engineering Materials. vol. 20 , nº 4. 9 p.
Kamel Touahir, Ali Bilek, Said Larbi, Said Djebali, Philippe Bocher. 2018. « 3D stress analysis of a loaded birefringent sphere by photoelastic experiment and finite elements method ». 24th Conference on Applications of Computer Algebra (Santiago de Compostela, Spain, June 18-22, 2018)
Fubin Tu, Dorian Delbergue, Thierry Klotz, Amrita Bag, Hongyan Miao, Charles Bianchetti, Myriam Brochu, Philippe Bocher, Martin Levesque. 2018. « Discrete element-periodic cell coupling model and investigations on shot stream expansion, Almen intensities and target materials ». International Journal of Mechanical Sciences. vol. 145 p. 353-366.
N. Vanderesse, B. Larregain, F. Bridier, P. Bocher. 2018. « Experimental assessment of high heating rates in induction heating with temperature-sensitive lacquers ». Journal of Materials Engineering and Performance. vol. 27 , nº 8. p. 3831-3843.
N. Vanderesse, A. Richter, N. Nuño, P. Bocher. 2018. « Measurement of deformation heterogeneities in additive manufactured lattice materials by Digital Image Correlation: Strain maps analysis and reliability assessment ». Journal of the Mechanical Behavior of Biomedical Materials. vol. 86 p. 397-408.
Wei Wang, Huaiju Liu, Caichao Zhu, Philippe Bocher, Heli Liu, Zhangdong Sun. 2018. « Evaluation of rolling contact fatigue of a carburized wind turbine gear considering the residual stress and hardness gradient ». Journal of Tribology. vol. 140 , nº 6. 10 p.
Samuel Bertrand, Davood Shahriari, Mohammad Jahazi, Henri Champliaud. 2018. « Linear friction welding process simulation of Ti-6Al-4V alloy: a heat transfer analysis of the conditioning phase ». 17th International Conference on Metal Forming (Metal Forming) (Toyohashi, Japan, Sept. 16-19, 2018) p. 1382-1390. Netherlands : Elsevier B.V..
Henri Champliaud, Valentin Vieillot, David Provencher, Ngan Van Lê. 2018. « Rapid 3D shape forming computation with piecewise heating lines using a fifth order spline formulation ». 30th European Modeling and Simulation Symposium (EMSS 2018) (Budapest , Hungary, Sept. 17-19, 2018) p. 204-209. Dime University of Genoa.
Hoan Huy Nguyen, Henri Champliaud, Van Ngan Lê. 2018. « Dynamic finite element modeling of metal spinning process with a stationary mandrel and a rotating tool ». 30th European Modeling and Simulation Symposium (EMSS 2018) (Budapest , Hungary, Sept. 17-19, 2018) p. 91-96. Dime University of Genoa.
Aboubakeur Benariba, Ahmed Bouzidane, Marc Thomas, Raynald Guilbault. 2018. « Numerical analysis of a rigid rotor mounted on four-pad hydrostatic squeeze film damper lubricated with micropolar lubricant ». Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. vol. 232 , nº 5. p. 513-524.
Sébastien Lalonde, Raynald Guilbault, Sébastien Langlois. 2018. « Numerical analysis of ACSR conductor-clamp systems undergoing wind-induced cyclic loads ». IEEE Transactions on Power Delivery. vol. 33 , nº 4. p. 1518-1526.
L. A. Hof, R. Wüthrich, T. Kwok. 2018. « Industry 4.0 and its impact on aviation ». Communication lors de la conférence : John Molson School of Business, John Molson Executive Centre, Client: Xiamen Air ( Montreal, QC, Canada, May 15, 2018 )
L. A. Hof, R. Wüthrich, T. Kwok. 2018. « Industry 4.0 – what lies ahead for manufacturing in the Sector? ». Communication lors de la conférence : John Molson School of Business, John Molson Executive Centre & HEC Paris ( Montreal, QC, Canada, May 10, 2018 )
Lucas A. Hof. 2018. « Indirect additive manufacturing and multiscale post-processing for fabrication of complex, high precision metal parts ». Communication lors de la conférence : RAPID + TCT 2018 Event and Conference ( Fort Worth, TX, USA, Apr. 23-26, 2018 )
Lucas A. Hof, Deependra Singh, Panteha Fallah, Rolf Wüthrich. 2018. « High precision electrochemical manufacturing processes to meet the demand of Industry 4.0 ». 18th International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN 2018) (Venice, Italy, June 04-08, 2018) Euspen.
Lucas A. Hof, Rolf Wuthrich. 2018. « Glass micro-cutting by Spark Assisted Chemical Engraving ». 2018 CSME International Congress (Toronto, ON, Canada, May 27-30, 2018) CSME.
Lucas A. Hof, Rolf Wuthrich. 2018. « Industry 4.0 Towards fabrication of mass-personalized parts on glass by Spark Assisted Chemical Engraving (SACE) ». Manufacturing Letters. vol. 15 p. 76-80.
Lucas A. Hof, Rolf Wüthrich. 2018. « Rapid prototyping of packaged glass devices: Eliminating a process step in the manufacturing workflow from micromachining to die singularizing ». Manufacturing Letters. vol. 17 p. 9-13.
Lucas Abia Hof. 2018. « High-precision micro-machining of glass for mass-personalization ». Thèse de doctorat. Montreal , Concordia University
Lucas Abia Hof, Rolf Wüthrich. 2018. « Electrochemical manufacturing to support industry 4.0 – Spark Assisted Chemical Engraving (SACE) ». Americas International Meeting on Electrochemistry and Solid State Science 2018 (AiMES 2018) (Cancun, Mexico, Sept. 30 - Oct. 04, 2018) Electrochemical Society.
Lucas Abia Hof, Rolf Wüthrich. 2018. « Electrochemical manufacturing to support industry 4.0 – Spark Assisted Chemical Engraving (SACE) ». Communication lors de la conférence : AiMES 2018 - ECS and SMEQ Joint International Meeting ( Cancun, Mexico, Sept. 30-Oct. 4, 2018 )
Stéphane Agnard, Bruce Hazel, Zhaoheng Liu. 2018. « Study of grinding tool profiling for robotic processes ». Machining Science and Technology. vol. 22 , nº 2. 22 p. p. 203-224.
Mourad Kedadouche, Zhaoheng Liu, Marc Thomas. 2018. « Bearing fault feature extraction using autoregressive coefficients, linear discriminant analysis and support vector machine under variable operating conditions ». Advances in Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the 5th International Conference on Condition Monitoring of Machinery in Non-stationary Operations, CMMNO’2016, 12–16 September 2016, Gliwice, Poland (Gliwice, Poland, Sept. 12-16, 2016) p. 339-352. Springer.
Mourad Kedadouche, Zhaoheng Liu, Marc Thomas. 2018. « Bearing fault feature extraction using autoregressive coefficients, linear discriminant analysis and support vector machine under variable operating conditions ». In Advances in Condition Monitoring of Machinery in Non-Stationary Operations Coll. «Applied Condition Monitoring», . p. 339-352. Springer.
Mourad Kedadouche, Sun Yulan, Zhaoheng Liu, Marc Thomas, Guillaume Charland-Arcand, Adrien Beck. 2018. « Design of a vibration isolator for the inertial navigation system of an autopilot dedicated to the operation of light drones ». 2018 9th International Conference on Mechanical and Aerospace Engineering (ICMAE) (Budapest, Hungary, Jul. 10-13, 2018) p. 73-78. IEEE.
Wenchao Li, Viet-Hung Vu, Zhaoheng Liu, Marc Thomas, Bruce Hazel. 2018. « Extraction of modal parameters for identification of time-varying systems using data-driven stochastic subspace identification ». Journal of Vibration and Control. vol. 24 , nº 20. p. 4781-4796.
Zhaoheng Liu, Kwok-wai Chung, Wei Wang. 2018. « A perturbed nonlinear model of an articulated vehicle with driver control ». Chaotic Modeling and Simulation. p. 295-304.
Essa Abrahim Abdulgader Saleem, Thien-My Dao, Zhaoheng Liu. 2018. « Multiple objective optimization and design of series-parallele using novel hybrid genetic algorithm meta-heuristic approach ». World Journal of Engineering and Technology. vol. 6 , nº 3. p. 532-555.
Z. Arhumah, M. Alkhabbat, X-T. Pham. 2018. « Heat effect on mechanical properties and microstructure of aluminum welding ». Affiche présentée lors de la conférence : REGAL student’s day ( Montreal, QC, Canada, June 18-19, 2018 )
D. D. Dang, X. T. Pham, P. Labbe, F. Torriano, J. F. Morissette, C. Hudon. 2018. « CFD analysis of turbulent convective heat transfer in a hydro-generator rotor-stator system ». Applied Thermal Engineering. vol. 130 p. 17-28.
M. Gharagozloo, X-T. Pham, C-C Nguyen. 2018. « Feasibility study of aluminium deposition by robotic MIG welding process ». CanWeld Conference 2018 (Winnipeg, MB, Canada, Sept. 12-13, 2018)
H.-C. Nguyen, X-T. Pham, M. Jahazi. 2018. « Implementing phase-field ductile fracture model for aluminum welded joint ». Affiche présentée lors de la conférence : REGAL student’s day ( Montreal, QC, Canada, June 18-19, 2018 )
T.-N. Tran, C.-C. Nguyen, X.-T. Pham. 2018. « Multi-physics modeling of aluminium laser welding process ». Affiche présentée lors de la conférence : REGAL student’s day ( Montreal, QC, Canada, June 18-19, 2018 )
Fatemeh Aghazadeh, Antoine Tahan, Marc Thomas. 2018. « Tool condition monitoring using spectral subtraction algorithm and artificial intelligence methods in milling process ». International Journal of Mechanical Engineering and Robotics Research. vol. 7 , nº 1. p. 30-34.
Fatemeh Aghazadeh, Antoine Tahan, Marc Thomas. 2018. « Tool condition monitoring using spectral subtraction and convolutional neural networks in milling process ». International Journal of Advanced Manufacturing Technology. vol. 98 , nº 9-12. p. 3217-3227.
Mahmoud Hammou, Ahmed Bouzidane, Marc Thomas, Aboubakeur Benariba, Mohamed Bouzit. 2018. « Static and dynamic characteristics of an orifice compensated three-pad hydrostatic squeeze film damper ». Industrial Lubrication and Tribology. vol. 70 , nº 6. p. 1078-1085.
Salim Meziani, Djamal Zarour, Marc Thomas. 2018. « Experimental studies for bearings degradation monitoring at an early stage using analysis of variance ». Diagnostyka. vol. 19 , nº 4. p. 81-87.
Amina Nemchi, Ahmed Bouzidane, Marc Thomas, Asma Abed. 2018. « Performance analysis of four-pad hydrostatic squeeze film dampers loaded between pads under laminar and turbulent flow conditions ». Tribology - Materials, Surfaces and Interfaces. vol. 12 , nº 2. p. 59-70.
Hamid Habibzadeh Boukani, Martin Viens, Souheil-Antoine Tahan, Martin Gagnon. 2018. « Case study on the integrity and nondestructive inspection of flux-cored arc welded joints of Francis turbine runners ». International Journal of Advanced Manufacturing Technology. vol. 98 , nº 5-8. p. 2201-2211.
A. Abid, D. Pereira, J. C. Fernandes, P. Belanger. 2017. « Sensitivity study of ultrasonic guided waves to cortical bone mechanical properties with axial and circumferential propagation ». Acta Acustica united with Acustica. vol. 103 , nº 3. p. 421-429.
Guillaume Boivin, Pierre Bélanger, Ricardo J. Zednik. 2017. « Torsional piezoelectric strain in monocrystalline paratellurite ». International Conference on Processing and Manufacturing of Advanced Materials (THERMEC) (Graz, Austria, May 29-June 03, 2016) p. 637-641. Trans Tech Publications.
P. Comot, P. Bocher, P. Belanger. 2017. « Ultrasonic guided wave inspection of Inconel 625 brazed lap joints: Simulation and experimentation ». NDT and E International. vol. 91 p. 71-78.
Hector de Castilla, Pierre Bélanger, Ricardo J. Zednik. 2017. « Dynamic piezoelectric behavior of lithium niobate at high temperature ». International Conference oN Processing and Manufacturing Of Advanced Materials (THERMEC) (Graz, Austria, May 29-June 03, 2016) p. 408-412. Trans Tech Publications.
Hector de Castilla, Pierre Bélanger, Ricardo J. Zednik. 2017. « High temperature characterization of piezoelectric lithium niobate using electrochemical impedance spectroscopy resonance method ». Journal of Applied Physics. vol. 122 , nº 24.
Frederic Dupont-Marillia, Mohammad Jahazi, Serge Lafreniere, Pierre Bélanger. 2017. « Influence of local mechanical properties of high strength steel from large size forged ingot on ultrasonic wave velocities ». 43rd Annual Review of Progress in Quantitative Nondestructive Evaluation (Atlanta, GA, USA, July 17-22, 2016) USA : American Institute of Physics.
Jorge Franklin Mansur Rodrigues Filho, Nicolas Tremblay, Soares da Fonseca Gláucio, Pierre Belanger. 2017. « The feasibility of structural health monitoring using the fundamental shear horizontal guided wave in a thin aluminum plate ». Materials. vol. 10 , nº 5.
Daniel Pereira, Guillaume Haiat, Julio Fernandes, Pierre Belanger. 2017. « Simulation of acoustic guided wave propagation in cortical bone using a semi-analytical finite element method ». Journal of the Acoustical Society of America. vol. 141 , nº 4. p. 2538-2547.
Dhawal R. Thakare, Alexandre Abid, Daniel Pereira, Julio Fernandes, Pierre Belanger, Prabhu Rajagopal. 2017. « Semi-analytical finite-element modeling approach for guided wave assessment of mechanical degradation in bones ». International Biomechanics. vol. 4 , nº 1. p. 17-27.
Christophe Travaglini, Christophe Bescond, Martin Viens, Pierre Belanger. 2017. « Feasibility of high frequency guided wave crack monitoring ». Structural Health Monitoring. vol. 16 , nº 4.
M. Anderson, A. L. Thielin, F. Bridier, P. Bocher, J. Savoie. 2017. « δ Phase precipitation in Inconel 718 and associated mechanical properties ». Materials Science and Engineering A. vol. 679 p. 48-55.
R. Bertrand, D. Texier, H. Robe, Y. Zedan, E. Feulvarch, P. Bocher. 2017. « Heterogeneous mechanical behavior of dissimilar FSWed joints assessed by OHR-DIC characterizations ». Communication lors de la conférence : 5th International Conference on Scientific and Technical Advances on Friction Stir Welding & Processing ( Metz, France, Oct. 11-13, 2017 )
Jianqiang Chen, Vincent Demers, Eve-Line Cadotte, Daniel Turner, Philippe Bocher. 2017. « Structural performance of inconel 625 superalloy brazed joints ». Journal of Materials Engineering and Performance. vol. 26 , nº 2. 7 p. p. 547-553.
D. Delbergue, M. Lévesque, P. Bocher. 2017. « About the importance of X-ray elastic constant determination in the precise measurement of residual stress profiles ». 13th International Conference on Shot Peening (ICSP) (Montréal, QC, Canada, 18-21 sept. 2017) p. 237-243.
D. Delbergue, D. Texier, M. Lévesque, P. Bocher. 2017. « Comparison of two X-Ray residual stress measurement methods: Sin2 ψ and Cos α, through the determination of a martensitic steel X-Ray elastic constant ». International Conference on Residual Stresses 2016 ICRS-10 p. 55-60. Millersville : Materials Research Forum LLC.
V. Demers, M. M. Elmajdoubi, P. Bocher. 2017. « Moldability of low-pressure powder injection molding feedstocks ». Advances in Powder Metallurgy & Particulate Materials 2017 : Conference Proceedings (Las Vegas , NV, USA, June 13-16, 2017) p. 401-414. Metal Powder Industries Federation.
Fayaz Foroozmehr, Yves Verreman, Jianqiang Chen, Denis Thibault, Philippe Bocher. 2017. « Effect of inclusions on fracture behavior of cast and wrought 13% Cr-4% Ni martensitic stainless steels ». Engineering Fracture Mechanics. vol. 175 p. 262-278.
Pedro Gálvez Hernández, Xavier Aguilo Lafarga, Nicolas Vanderesse, Fernando Quevedo González, Philippe Bocher, Natalia Nuño. 2017. « Analysis of porous TI-6AL-4V structures made by selective laser sintering for intervertebral cages ». Communication lors de la conférence : 23rd Congress of the European Society of Biomechanics ( Sevilla, Spain, July 02-05, 2017 )
Hamid Javadi, Walid Jomaa, Damien Texier, Myriam Brochu, Philippe Bocher. 2017. « Surface roughness effects on the fatigue behavior of as-machined inconel 718 ». 8th International Conference on Materials Structure and Micromechanics of Fracture (MSMF 8) (Brno, Czech republic, July 27-29, 2016) p. 306-309. Trans Tech Publications Ltd.
Walid Jomaa, Augustin Gakwaya, Philippe Bocher. 2017. « Modeling of materials behavior in finite element analysis and simulation of machining processes : Identification techniques and challenges ». In Advanced Machining Processes: Innovative Modeling Techniques Coll. «Manufacturing Design and Technology Series», . p. 281-318. CRC Press.
Walid Jomaa, Julie Lévesque, Philippe Bocher, Arnaud Divialle, Augustin Gakwaya. 2017. « Optimization study of dry peripheral milling process for improving aeronautical part integrity using Grey relational analysis ». International Journal of Advanced Manufacturing Technology. vol. 91 , nº 1-4. 12 p. p. 931-942.
Walid Jomaa, Oussama Mechri, Julie Levesque, Victor Songmene, Philippe Bocher, Augustin Gakwaya. 2017. « Finite element simulation and analysis of serrated chip formation during highspeed machining of AA7075T651 alloy ». Journal of Manufacturing Processes. vol. 26 p. 446-458.
Walid Jomaa, Victor Songmene, Philippe Bocher. 2017. « Predictive analytical modeling of cutting forces generated by high-speed machining of ductile and hard metals ». Machining Science and Technology. vol. 21 , nº 3. 27 p. p. 335-361.
Walid Jomaa, Victor Songmene, Philippe Bocher, Augustin Gakwaya. 2017. « Fea-based comparative investigation on high speed machining of aluminum alloys aa6061-t6 and aa7075-t651 ». 9th International Congress on Precision Machining, (ICPM 2017) (Athens, Greece, Sept. 06-09, 2017) p. 347-353.
Xavier Aguilo Lafarga, Pedro Gálvez Hernández, Nicolas Vanderesse, Fernando Quevedo González, Philippe Bocher, Natalia Nuño. 2017. « Effect of the building orientation on mechanical properties of porous structures made by additive manufacturing ». Communication lors de la conférence : 23rd Congress of the European Society of Biomechanics ( Sevilla, Spain, July 02-05, 2017 )
Kevin McMeekin, Frédéric Sirois, Maxime Tousignant, Philippe Bocher. 2017. « Improving the accuracy of time-harmonic FE simulations in induction heating applications Towards better ferromagnetic material models ». COMPEL - The International Journal for Computation and Mathematics in Electrical and Electronic Engineering. vol. 36 , nº 2. p. 526-534.
Shilan Meimandi, Nicolas Vanderesse, Denis Thibault, Philippe Bocher, Martin Viens. 2017. « Macro-defects characterization in cast CA-6NM martensitic stainless steel ». Materials Characterization. vol. 124 p. 31-39.
N. Siredey-Schwaller, J. Hamel-Akre, L. Peltier, A. Hazotte, P. Bocher. 2017. « Solidification sequence of Ni-Si-Cr ~3wt% B brazing alloys ». Welding in the World. vol. 61 , nº 6. p. 1253-1265.
J. C. Stinville, M. P. Echlin, P. G. Callahan, V. M. Miller, D. Texier, F. Bridier, P. Bocher, T. M. Pollock. 2017. « Measurement of strain localization resulting from monotonic and cyclic loading at 650C in nickel base superalloys ». Experimental Mechanics. vol. 57 , nº 8. p. 1289-1309.
Binhan Sun, Nicolas Vanderesse, Fateh Fazeli, Colin Scott, Jianqiang Chen, Philippe Bocher, Mohammad Jahazi, Stephen Yue. 2017. « Discontinuous strain-induced martensite transformation related to the Portevin-Le Chatelier effect in a medium manganese steel ». Scripta Materialia. vol. 133 p. 9-13.
Denis Thibault, Shilan Meimandi, Nicolas Vanderesse, Philippe Bocher, Martin Viens, Myriam Brochu, Martin Gagnon. 2017. « Linking defects found by non-destructive testing in stainless steel castings to the fatigue analysis of hydraulic turbines ». Communication lors de la conférence : 3rd International Symposium on Fatigue Design and Material Defects (FDMD) ( Lecco, Italy, Sept. 19-22, 2017 )
Heithem Touazine, Jordan Akab, Mohammad Jahazi, Antoine Tahan, Walid Jomaa, Philippe Bocher. 2017. « Modeling of the microstructure alteration induced by hard turning of Inconel 718 ». International Journal of Advanced Manufacturing Technology. vol. 93 , nº 9-12. 8 p. p. 3705-3712.
Heithem Touazine, Mohammad Jahazi, Philippe Bocher. 2017. « Accurate determination of damaged subsurface layers in machined Inconel 718 ». International Journal of Advanced Manufacturing Technology. vol. 88 , nº 9-12. 9 p. p. 3419-3427.
Fubin Tu, Dorian Delbergue, Hongyan Miao, Thierry Klotz, Myriam Brochu, Philippe Bocher, Martin Levesque. 2017. « A sequential DEM-FEM coupling method for shot peening simulation ». Surface and Coatings Technology. vol. 319 p. 200-212.
Yassine Bouissa, Henri Champliaud, Mohammad Jahazi, Louis-Philippe Lapierre-Boire, Jean-Benoît Morin, Nicolas Poulain. 2017. « Modeling heterogeneities effects on phase transformation during quenching of large size forged steel ingots ». Communication lors de la conférence : 14th U.S. National Congress on Computational Mechanics (USNCCM) ( Montreal, QC, Canada, July 17-20, 2017 )
Jean-Loup Curtat, Jacques Lanteigne, Henri Champliaud, Zhaoheng Liu, Jean-Benoît Lévesque. 2017. « Influence of hammer peening on fatigue life of E309L steel used for 13%Cr-4%Ni blade runner repairs ». International Journal of Fatigue. vol. 100 p. 68-77.
Zhengkun Feng, Henri Champliaud, Louis Mathieu. 2017. « Investigations of a reconfigurable pressing setup for manufacturing blades of large francis turbines runners from very thick plates ». 29th European Modeling and Simulation Symposium (EMSS) (Barcelona, Spain, Sept. 18-20, 2017) p. 212-220. CAL-TEK S.r.l..
Mathieu Gendron, Bruce Hazel, Eric Boudreault, Henri Champliaud, Xuan-Tan Pham. 2017. « Modeling circular inductors coupled to a semi-infinite magnetic medium considering the proximity effect ». Journal of Electromagnetic Waves and Applications. vol. 31 , nº 13. 23 p. p. 1232-1254.
Seyedbehzad Ghafarizadeh, Amir Masoud Tahvilian, Jean-François Chatelain, Zhaoheng Liu, Henri Champliaud, Gilbert Lebrun. 2017. « Numerical simulation of ball-end milling with SPH method ». International Journal of Advanced Manufacturing Technology. vol. 88 , nº 1. 8 p. p. 401-408.
Jacques Luk-Cyr, Rayan El-Bawab, Henri Champliaud, Jacques Lanteigne, Aurelian Vadean. 2017. « Sequential approximate optimization of industrial hammer peening using finite element simulations ». Structural and Multidisciplinary Optimization. vol. 55 , nº 3. 12 p. p. 767-778.
Jacques Luk-Cyr, Daniel Paquet, Jacques Lanteigne, Henri Champliaud, Aurelian Vadean. 2017. « A unified plasticity methodology for rate- and temperature-sensitive alloys exhibiting a non-linear kinematic hardening behavior ». Acta Mechanica Solida Sinica. vol. 12 , nº 2. 11 p. p. 726-737.
S. Sarafan, P. Wanjara, J. Gholipour, H. Champliaud, L. Mathieu. 2017. « Mechanical properties of electron beam welds in heavy-section UNS S41500 martensitic stainless steel ». International Journal of Advanced Manufacturing Technology. vol. 91 , nº 9/12. 10 p. p. 4141-4150.
Sheida Sarafan, Priti Wanjara, Javad Gholipour, Henri Champliaud, Louis Mathieu. 2017. « Mehanical properties of electron beam welded joints in thick gage CA6NM stainless steel ». Journal of Materials Engineering and Performance. vol. 26 , nº 10. p. 4768-4780.
F. Mirakhorli, X. Cao, X. T. Pham, P. Wanjara, J. L. Fihey. 2017. « Phase structures and morphologies of tempered CA6NM stainless steel welded by hybrid laser-arc process ». Materials Characterization. vol. 123 p. 264-274.
F. Mirakhorli, X. Cao, X. T. Pham, P. Wanjara, J. L. Fihey. 2017. « Technical challenges in narrow-gap root pass welding during tandem and hybrid laser-arc welding of a thick martensitic stainless steel ». International conference on processing and manufacturing of advanced materials (THERMEC) (Graz, Austria, May 29-June 03, 2016) p. 1305-1310. Trans Tech Publications.
Zahra Nili Ahmadabadi, Frédéric Laville, Raynald Guilbault. 2017. « An empirical prediction law for quasi-static nail-particle board penetration resistance ». International Mechanical Engineering Congress and Exposition (IMECE 2017) (Tampa, FL, USA, Nov. 03-09, 2017) p. ASME. American Society of Mechanical Engineers (ASME).
Sébastien Lalonde, Raynald Guilbault, Sébastien Langlois. 2017. « Modeling multilayered wire strands, a strategy based on 3D finite element beam-to-beam contacts - Part II: Application to wind-induced vibration and fatigue analysis of overhead conductors ». International Journal of Mechanical Sciences. vol. 126 p. 297-307.
Sébastien Lalonde, Raynald Guilbault, Frédéric Légeron. 2017. « Modeling multilayered wire strands, a strategy based on 3D finite element beam-to-beam contacts - Part I: Model formulation and validation ». International Journal of Mechanical Sciences. vol. 126 16 p. p. 281-296.
Panteha Fallah, Lucas A. Hof, Rolf Wüthrich. 2017. « Electroforming of non-conductive 3D printed parts ». Proceedings of the 26th Canadian Congress of Applied Mechanics (CANCAM 2017) (Victoria, BC, Canada, May 29 - June 01, 2017) Canadian Congress of Applied Mechanics.
L. A. Hof, L. Heinrich, R. Wuthrich. 2017. « Towards high precision manufacturing of glass tools by Spark Assisted Chemical Engraving (SACE) for micro forming techniques ». 2017 World Congress on Micro and Nano Manufacturing (WCMNM) : A Joint Conference of ICOMM/4M/IFMM (Kaohsiung City, Taiwan, Mar. 27-30, 2017)
L. A. Hof, R. Wüthrich. 2017. « Electrochemistry 4.0 ». Communication lors de la conférence : 231st Electrochemical Society Meeting (ECS) ( New Orleans, LA, USA, May 28 - June 01, 2017 )
L. A. Hof, R. Wuthrich. 2017. « Micro-/nanofabrication in the era of Industry 4.0 - Spark Assisted Chemical Engraving (SACE) - a versatile technology for glass machining and nanoparticle deposition ». Affiche présentée lors de la conférence : 1st National Conference : Converging on Nanomanufacturing : Innovation 360 ( Montréal, QC, Canada, Sept. 25-26, 2017 )
Lucas A. Hof, Md Masiar Rahman, Rolf Wuthrich. 2017. « Using Taylor vortices to create a film of nanoparticles for dip-coating ». Manufacturing Letters. vol. 13 p. 21-24.
Lucas A. Hof, Jana Abou Ziki. 2017. « Micro-hole drilling on glass substrates-A review ». Micromachines. vol. 8 , nº 2.
Lucas Abia Hof, Xin Guo, Minseok Seo, Rolf Wuthrich, Jesse Greener. 2017. « Glass imprint templates by spark assisted chemical engraving for microfabrication by hot embossing ». Micromachines. vol. 8 , nº 1.
Lucas Hof, Rolf Wuthrich. 2017. « Multiscale post-processing of metal additive manufactured parts by electro-polishing technology ». RAPID + TCT 2017 Event and Conference (Pittsburgh, PA, USA, May 08-11, 2017) SME.
Lucas Hof, Rolf Wuthrich. 2017. « Multiscale post-processing of metal additive manufactured parts by electro-polishing technology ». Communication lors de la conférence : RAPID + TCT 2017 Event and Conference ( Pittsburgh, PA, USA, May 08-11, 2017 )
D. Singh, L. A. Hof, R. Wuthrich. 2017. « Micro and nano 3D Feature deposition using localized electrochemical deposition ». Communication lors de la conférence : 1st National Conference : Converging on Nanomanufacturing : Innovation 360 ( Montréal, QC, Canada, Sept. 25-26, 2017 )
Mourad Kedadouche, Zhaoheng Liu. 2017. « Fault feature extraction and classification based on WPT and SVD: Application to element bearings with artificially created faults under variable conditions ». Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science. vol. 231 , nº 22. p. 4186-4196.
Wenchao Li, Viet-Hung Vu, Zhaoheng Liu, Marc Thomas, Bruce Hazel. 2017. « Application of adaptable functional series vector time-dependent autoregressive model for extraction of real modal parameters for identification of time-varying systems ». Measurement: Journal of the International Measurement Confederation. vol. 103 p. 143-156.
Zhaoheng Liu, Kwok-Wai Chung, Wei Wang. 2017. « A perturbed nonlinear model of an articulated vehicle with driver control ». 10th Chaotic Modeling and Simulation International Conference (Barcelona, Spain, May 30 - 02 June, 2017) p. 549-558. International Society for the Advancement of Science and Technology.
Essa Abrahim Abdulgader Saleem, Thien-My Dao, Liu Zhaoheng. 2017. « Multi-objective optimization of multi-state reliability system using hybrid metaheuristic genetic algorithm and fuzzy function for redundancy allocation ». American Journal of Engineering Research. vol. 6 , nº 10. p. 98-107.
Viet-Hung Vu, Zhaoheng Liu, Marc Thomas, Bruce Hazel. 2017. « Modal analysis of a light-weight robot with a rotating tool installed at the end effector ». Proceedings of the Institution of Mechanical Engineers, Part C : Journal of Mechanical Engineering Science. vol. 231 , nº 9. p. 1664-1676.
Wei Wang, Fei Liu, Zhaoheng Liu, Chao Yun. 2017. « Prediction of depth of cut for robotic belt grinding ». International Journal of Advanced Manufacturing Technology. vol. 91 , nº 1. 10 p. p. 669-708.
V. Sabri, S. Sattarpanah, S. A. Tahan, J. C. Cuillière, V. François, X. T. Pham. 2017. « A robust and automated FE-based method for fixtureless dimensional metrology of non-rigid parts using an improved numerical inspection fixture ». International Journal of Advanced Manufacturing Technology. vol. 92 , nº 5-8. p. 2411-2423.
Ngoc-Hung Vu, Vincent François, Jean-Christophe Cuillière, Xuan-Tan Pham. 2017. « Development of finite strain shell elements for multi-layered fiber-reinforced materials applied for non-rigid parts deformation during assembly process ». Design, Manufacturing and Applications of Composites : Proceedings of the Eleventh Joint Canada-Japan Workshop on Composites and the First Joint Canada-Japan-Vietnam Workshop on Composites August 2016, Ho Chi Minh, Vietnam (Ho Chi Minh, Vietnam, Aug. 08-12, 2016) p. 96-103. DEStech publications.
Asma Abed, Ahmed Bouzidane, Marc Thomas, Hamou Zahloul. 2017. « Performance characteristics of a three-pad hydrostatic squeeze film damper compensated with new electrorheological valve restrictors ». Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology. vol. 231 , nº 7. p. 889-899.
Hicham Aboshighiba, Ahmed Bouzidane, Marc Thomas, Faiza Ghezali, Amina Nemchi, Asmaa Abed. 2017. « Pressure distribution in orifice-compensated turbulent hydrostatic bearing with fluid inertia effects using numerical simulations via Navier-Stokes ». Tribology - Materials, Surfaces and Interfaces. vol. 11 , nº 1. 11 p. p. 19-29.
Surajdeen Adewusi, Marc Thomas. 2017. « Stress and strain distributions in the human hand-arm system using finite element analysis ». International Journal of Engineering and Technology (UAE). vol. 6 , nº 2. p. 21-28.
Faiza Ghezali, Ahmed Bouzidane, Marc Thomas. 2017. « 3D Numerical investigation of pressure field of an orifice compensated hydrostatic bearing ». Mechanics and Industry. vol. 18 , nº 1.
Yacine Imaouchen, Mourad Kedadouche, Rezak Alkama, Marc Thomas. 2017. « A Frequency-Weighted Energy Operator and complementary ensemble empirical mode decomposition for bearing fault detection ». Mechanical Systems and Signal Processing. vol. 82 p. 103-116.
Salim Meziani, Djamal Zarour, Marc Thomas. 2017. « Experimental study for early detection of bearing defects by vibration and acoustic emission ». 23ème Congrès Français de Mécanique (CFM) (Lille, France, 28 août - 1er sept. 2017) Association Française de Mécanique (AFM).
Marc Thomas, Frédéric Laville. 2017. « Simulation des vibrations mécaniques par Matlab, Simulink et Ansys ». 2e édition Québec ; Montréal : Presses de l'Université du Québec ; École de technologie supérieure. 700 p.
Djamal Zarour, Salim Meziani, Mourad Kedadouche, Marc Thomas. 2017. « Faulty bearing features by variational mode decomposition ». 30th JVE International Conference (Phuket, Thailand, Dec. 16-17, 2017) p. 29-34. JVE international.
H. H. Boukani, E. Mohseni, M. Viens. 2017. « Effect of fatigue crack orientation on the sensitivity of eddy current inspection in martensitic stainless steels ». Communication lors de la conférence : NDT in Canada 2017 ( Québec, QC, Canada, June 06-08, 2017 )
E. Mohseni, M. Viens. 2017. « Sensitivity of eddy current signals to probe's tilt and lift-off while scanning semi-elliptical surface notches - a finite element modeling approach ». Communication lors de la conférence : NDT in Canada 2017 ( Québec, QC, Canada, June 06-08, 2017 )
Pierre Belanger, Guillaume Boivin. 2016. « Development of a low frequency omnidirectional piezoelectric shear horizontal wave transducer ». Smart Materials and Structures. vol. 25 , nº 4. 10 p.
Pierre Belanger, Guillaume Boivin. 2016. « Development of an omnidirectional SH0 piezoceramic transducer ». 42nd annual review of progress in quantitative nondestructive evaluation : incorporating the 6th European-American Workshop on Reliability of NDE (Minneapolis, MN, USA, July 26-31, 2015) AIP Publishing.
Pierre Belanger, Guillaume Boivin. 2016. « Piezoceramic omnidirectional transduction of the fundamental shear horizontal guide wave mode ». Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, and Civil Infrastructure 2016 (Las Vegas, NV, USA, Mar. 20-24, 2016) USA : SPIE.
Guillaume Boivin, Nicolas Tremblay, Ricardo Zednik, Pierre Bélanger. 2016. « Piezoelectric low frequency shear horizontal guided wave transduction ». The Journal of the Acoustical Society of America. vol. 140 , nº 4. p. 3034-3034.
Guillaume Boivin, Martin Viens, Pierre Belanger. 2016. « Development of a low frequency shear horizontal piezoelectric transducer for the generation of plane SH waves ». 42nd annual review of progress in quantitative nondestructive evaluation : incorporating the 6th European-American Workshop on Reliability of NDE (Minneapolis, MN, USA, July 26-31, 2015) AIP Publishing.
Pierre Comot, Philippe Bocher, Pierre Belanger. 2016. « Ultrasonic guided wave inspection of Inconel 625 brazed lap joints ». Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, and Civil Infrastructure 2016 (Las Vegas , NV, USA, Mar. 20-24, 2016) SPIE.
Shreyank Gupta, Guillaume Haïat, Catherine Laporte, Pierre Bélanger. 2016. « Modeling wave propagation through the skull for ultrasonic transcranial Doppler ». Journal of the Acoustical Society of America. vol. 140 , nº 4. p. 3189.
Christophe Travaglini, Christophe Bescond, Dermartonne Ramos Franca, Silvio E. Kruger, Martin Viens, Pierre Bélanger. 2016. « Scattering of high order guided wave modes around a through-thickness circular hole ». 42nd annual review of progress in quantitative nondestructive evaluation : incorporating the 6th European-American Workshop on Reliability of NDE (Minneapolis, MN, USA, July 26-31, 2015) AIP Publishing.
Maniya Aghasibeig, Hossein Monajatizadeh, Philippe Bocher, Ali Dolatabadi, Rolf Wuthrich, Christian Moreau. 2016. « Cold spray as a novel method for development of nickel electrode coatings for hydrogen production ». International Journal of Hydrogen Energy. vol. 41 , nº 1. p. 227-238.
Mohsen Mokhtabad Amrei, Hossein Monajati, Denis Thibault, Yves Verreman, Philippe Bocher. 2016. « Effects of various post-weld heat treatments on austenite and carbide formation in a 13Cr4Ni steel multipass weld ». Metallography, Microstructure, and Analysis. vol. 5 , nº 1. p. 50-61.
Mohsen Mokhtabad Amrei, Hossein Monajati, Denis Thibault, Yves Verreman, Lionel Germain, Philippe Bocher. 2016. « Microstructure characterization and hardness distribution of 13Cr4Ni multipass weld metal ». Materials Characterization. vol. 111 p. 128-136.
M. Anderson, F. Bridier, J. Gholipour, M. Jahazi, P. Wanjara, P. Bocher, J. Savoie. 2016. « Mechanical and metallurgical evolution of stainless steel 321 in a multi-step forming process ». Journal of Materials Engineering and Performance. vol. 25 , nº 4. 13 p. p. 1526-1538.
A. Elhadi, A. Bouchoucha, W. Jomaa, Y. Zedan, T. Schmitt, P. Bocher. 2016. « Study of surface wear and damage induced by dry sliding of tempered AISI 4140 steel against hardened AISI 1055 steel ». Tribology in Industry. vol. 38 , nº 4. p. 475-485.
Landry Giraud, Hugo Robe, Christophe Claudin, Christophe Desrayaud, Philippe Bocher, Eric Feulvarch. 2016. « Investigation into the dissimilar friction stir welding of AA7020-T651 and AA6060-T6 ». Journal of Materials Processing Technology. vol. 235 p. 220-230.
W. Jomaa, J. Mechri, J. Lévesque, A. Gakwaya, V. Songmene, P. Bocher. 2016. « Finite element analysis of serrated chip formation in machining of 7075-T651 alluminum alloy ». XXVIII International Mineral Processing Congress (IMPC) (Québec, QC, Canada, Sept. 11-15, 2016)
W. Jomaa, V. Songmene, P. Bocher. 2016. « An investigation of machining-induced residual stresses and microstructure of induction-hardened AISI 4340 steel ». Materials and Manufacturing Processes. vol. 31 , nº 7. 7 p. p. 838-844.
Walid Jomaa, Victor Songmene, Philippe Bocher. 2016. « An hybrid approach based on machining and dynamic tests data for the identification of material constitutive equations ». Journal of Materials Engineering and Performance. vol. 25 , nº 3. p. 1010-1027.
Mahdi Masoumi, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher. 2016. « Friction stir welding of AA2024 and AA2198 Aluminum alloys: effect of tool geometry and process parameters ». 2nd International Conference on Welding and Non Destructive Testing (ICWNDT) (Tehran, Iran, Dec. 20-21, 2016)
Mahdi Masoumi, Yasser Zedan, Damien Texier, Mohammad Jahazi, Philippe Bocher. 2016. « The influence of tool geometry on mechanical properties of friction stir welded AA-2024 and AA-2198 joints ». 34th International Conference and Exhibition of ICSOBA (Quebec, QC, Canada, Oct. 03-06, 2016) The International Committee for Study of Bauxite, Alumina & Aluminium (ICSOBA).
Hesser Taboada Michel, Layla Sasaki Reda, Georgia Effgen Santos, Jonathan Cormier, Christian Dumont, Patrick Villechaise, Philippe Bocher, Damien Texier, Eric Georges, Florent Bridier, Florence Hamon, Alexandre Devaux. 2016. « Mechanical properties of cast wrought hybrid disks ». Superalloys 2016: Proceedings of the 13th International Symposium on Superalloys (Seven Springs, PA, USA, Sept. 11-15, 2016) p. 539-548. Minerals, Metals and Materials Society.
Marc Novelli, Jean-Jacques Fundenberger, Philippe Bocher, Thierry Grosdidier. 2016. « On the effectiveness of surface severe plastic deformation by shot peening at cryogenic temperature ». Applied Surface Science. vol. 389 p. 1169-1174.
Meysam H. Pourian, Florent Bridier, Philippe Pilvin, Philippe Bocher. 2016. « Prediction of crack initiation sites in alpha Ti-alloys microstructures under dwell-fatigue using Cellular Automaton simulation method ». International Journal of Fatigue. vol. 85 p. 85-97.
Fernando Quevedo Gonzalez, Nicolas Vanderesse, Anthony Barraud, Philippe Bocher, Natalia Nuño. 2016. « Prediction and measurement of apparent elastic moduli in porous additive manufactured materials for new generation of hip implants ». Affiche présentée lors de la conférence : 10th World Biomaterials Congress ( Montreal, QC, Canada, May 17-22, 2016 )
Vincent Savaria, Florent Bridier, Philippe Bocher. 2016. « Predicting the effects of material properties gradient and residual stresses on the bending fatigue strength of induction hardened aeronautical gears ». International Journal of Fatigue. vol. 85 p. 70-84.
J. C. Stinville, M. P. Echlin, D. Texier, F. Bridier, P. Bocher, T. M. Pollock. 2016. « Sub-grain scale digital image correlation by electron microscopy for polycrystalline materials during elastic and plastic deformation ». Experimental Mechanics. vol. 56 , nº 2. p. 197-216.
D. Texier, Y. Zedan, T. Amoros, E. Feulvarch, J. C. Stinville, P. Bocher. 2016. « Near-surface mechanical heterogeneities in a dissimilar aluminum alloys friction stir welded joint ». Materials and Design. vol. 108 p. 217-229.
N. Vanderesse, M. Anderson, F. Bridier, P. Bocher. 2016. « Inter- and intragranular delta phase quantitative characterization in Inconel 718 by means of image analysis ». Journal of Microscopy. vol. 261 , nº 1. p. 79-87.
N. Vanderesse, I. Ky, F. Quevedo Gonzalez, N. Nuño, P. Bocher. 2016. « Image analysis characterization of periodic porous materials produced by additive manufacturing ». Materials & Design. vol. 92 p. 767-778.
Henri Champliaud, Zhengkun Feng, David Provencher, Danick Tousignant, Javad Gholipour. 2016. « Piecewise fifth order spline interpolation for line heating forming process ». ASME International Mechanical Engineering Congress and Exposition (IMECE2016) (Phoenix, AZ, USA, Nov. 11-17, 2016) ASME.
Mathieu Gendron, Éric Boudreault, Bruce Hazel, Xuan-Tan Pham, Henri Champliaud. 2016. « Non-linear optimization of a new robotic induction process for local heat treatment using thermal finite element analysis ». International Journal of Advanced Manufacturing Technology. vol. 84 , nº 5. p. 1013-1029.
Jacques Luk-Cyr, Rayan El-Bawab, Jacques Lanteigne, Henri Champliaud, Aurelian Vadean. 2016. « Mechanical properties of 75% Ar /25% CO2 flux-cored arc welded E309L austenitic stainless steel ». Materials Science and Engineering A. vol. 678 p. 197-203.
M. Saboori, H. Champliaud, J. Gholipour, A. Gakwaya, J. Savoie, P. Wanjara. 2016. « Extension of flow stress-strain curves of aerospace alloys after necking ». International Journal of Advanced Manufacturing Technology. vol. 83 , nº 1-4. p. 313-323.
M. Saboori, J. Gholipour, H. Champliaud, P. Wanjara, A. Gakwaya, J. Savoie. 2016. « Prediction of burst pressure in multistage tube hydroforming of aerospace alloys ». Journal of Engineering for Gas Turbines and Power. vol. 138 , nº 8. 5 p.
Jamel Salem, Henri Champliaud, Zhengkun Feng, Thien-My Dao. 2016. « Experimental analysis of an asymmetrical three-roll bending process ». International Journal of Advanced Manufacturing Technology. vol. 83 , nº 9. p. 1823-1833.
S. Sarafan, J.-B. Lévesque, P. Wanjara, J. Gholipour, H. Champliaud. 2016. « Distortion and residual stresses in electron beam-welded hydroelectric turbine materials ». Science and Technology of Welding and Joining. vol. 21 , nº 6. p. 473-478.
S. Sarafan, P. Wanjara, J. Gholipour, H. Champliaud. 2016. « Global and local characteristics of an autogenous single pass electron beam weld in thick gage UNS S41500 steel ». Materials Science and Engineering: A. vol. 666 p. 360-371.
Amir Masoud Tahvilian, Bruce Hazel, Farzad Rafieian, Zhaoheng Liu, Henri Champliaud. 2016. « Force model for impact cutting grinding with a flexible robotic tool holder ». International Journal of Advanced Manufacturing Technology. vol. 85 , nº 1. p. 133-147.
Fatemeh Mirakhorli, Xinjin Cao, Xuan-Tan Pham, Priti Wanjara, Jean-Luc Fihey. 2016. « Hybrid laser-arc welding of 10-mm-thick cast martensitic stainless steel CA6NM: as-welded microstructure and mechanical properties ». Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. vol. 47 , nº 7. 19 p. p. 3545-3563.
Fatemeh Mirakhorli, Xinjin Cao, Xuan-Tan Pham, Priti Wanjara, Jean-Luc Fihey. 2016. « Post-weld tempered microstructure and mechanical properties of hybrid laser-arc welded cast martensitic stainless steel CA6NM ». Metallurgical and Materials Transactions B: Process Metallurgy and Materials Processing Science. vol. 47 , nº 6. p. 3245-3256.
Z. Nili Ahmadabadi, Frédéric Laville, Raynald Guilbault. 2016. « Time domain identification and ranking of noise sources in a pneumatic nail gun ». Applied Acoustics. vol. 114 p. 191-202.
Guillaume Corriveau, Raynald Guilbault, Antoine Tahan, Robert Sabourin. 2016. « Bayesian network as an adaptive parameter setting approach for genetic algorithms ». Complex & Intelligent Systems. vol. 2 , nº 1. p. 1-22.
Raynald Guilbault, Sébastien Lalonde. 2016. « Early diagnostic of concurrent gear degradation processes progressing under time-varying loads ». Mechanical Systems and Signal Processing. vol. 76-77 p. 337-352.
L. A. Hof, J.D. Abou Ziki, R. Wuthrich. 2016. « Tool-glass bonding phenomenon during glass micro-machining by Spark Assisted Chemical Engraving (SACE) - Issues and opportunities ». Affiche présentée lors de la conférence : International Conference on Design and Production Engineering ( Berlin, Germany, July 25-26, 2016 )
L. A. Hof, C. Goyer, R. Wüthrich. 2016. « Microstructuring of glass by spark assisted chemical engraving (SACE) ». Communication lors de la conférence : International Conference on Design and Production Engineering ( Berlin, Germany, July 25-26, 2016 )
L. A. Hof, B. Presley, D. VanTran, R. Wüthrich. 2016. « Spark Assistant Chemical Engraving (SACE) – an innovative tool for the microfluidic community ». Communication lors de la conférence : FluidicMEMS : HiFi Bio ( Boston, MA, USA, Oct. 26, 2016 )
L. A. Hof, M. M. Rahman, R. Wuthrich. 2016. « Multiscale post-processing of metal additive manufactured parts by electro-polishing technology ». Communication lors de la conférence : Salon de la Technologie de Fabrication de Montréal (STFM) ( Montréal, QC, Canada, 15-18 mai 2016 )
L. A. Hof, R. Wüthrich. 2016. « Electrochemical manufacturing processes to meet the demand of Industry 4.0 ». Affiche présentée lors de la conférence : Montreal Summit on Innovation - The Manufacturing Sector at the Conquest of the 4th Industrial Revolution ( Montréal, QC, Canada, 24 nov. 2016 )
L. A. Hof, R. Wüthrich. 2016. « Electrochemical processes to meet the needs of industry 4.0 ». Communication lors de la conférence : Forum Industriel CREPEC ( Montréal, QC, Canada, 20 oct. 2016 )
L. A. Hof, R. Wuthrich. 2016. « Industry 4.0 – towards fabrication of ultra-customized parts on glass by Spark Assisted Chemical Engraving (SACE) ». Proceedings of the Canadian Society for Mechanical Engineering International Congress 2016 (Kelowna, BC, Canada, June 26-29, 2016)
L. A. Hof, R. Wüthrich. 2016. « The digital engineer - New challenges for the Canadian Universities ». Communication lors de la conférence : Advanced Manufacturing Canada (AMC) 2016 ( Toronto, ON, Canada, Nov. 02-03, 2016 )
Lucas Abia Hof, Frederic Charbonneau, Diana Consuelo Rodriguez Burbano, Ana Maria Ibarra-Ruiz, John A. Capobianco, Rolf Wuthrich. 2016. « Spark Assisted Chemical Engraving (SACE) – from subtractive to additive manufacturing technology ». 11th International Conference on Micromanufacturing (ICOMM 2016) (Orange County, CA, USA, Mar. 29-31, 2016)
Lucas Abia Hof, Md Masiar Rahman, Rolf Wüthrich. 2016. « Multiscale post-processing of metal additive manufactured parts by electro-polishing technology ». 16th International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN 2016) (Nottingham, UK, May 30 - June 03, 2016) Euspen.
Lucas Hof, Patrick Thibaut, Rolf Wüthrich. 2016. « Spark Assisted Chemical Engraving (SACE) – an innovative technology with high potential for industry ». 16th International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN 2016) (Nottingham, UK, May 30 - June 03, 2016) Euspen.
Lucas Hof, Rolf Wüthrich. 2016. « Micromachining glass with in situ fabricated micro-tools ». 16th International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN 2016) (Nottingham, UK, May 30 - June 03, 2016) Euspen.
M. M. Rahman, L. A. Hof, R. Wuthrich. 2016. « Multiscale electropolishing of additive manufactured and standard grade titanium alloys by pulsed voltages ». Proceedings of the Canadian Society for Mechanical Engineering International Congress 2016 (Kelowna, BC, Canada, June 26-29, 2016)
R. Wuthrich, L. A. Hof. 2016. « Electrochemical processes to meet the needs of industry 4.0 ». Proceedings of the Canadian Society for Mechanical Engineering International Congress 2016 (Kelowna, BC, Canada, June 26-29, 2016)
Mourad Kedadouche, Zhaoheng Liu, Viet-Hung Vu. 2016. « A new approach based on OMA-empirical wavelet transforms for bearing fault diagnosis ». Measurement: Journal of the International Measurement Confederation. vol. 90 p. 292-308.
Zhaoheng Liu. 2016. « Research work on robotic grinding for in-situ repairs and maintenance of hydroelectric equipment ». Communication lors de la conférence : Department of Mechanical and Manufacturing Engineering, Aalborg University ( Aalborg, Denmark, Aug. 12, 2016 )
Zhaoheng Liu, Kun Hu, Kwok-Wai Chung. 2016. « Nonlinear analysis of a closed-loop tractor-semitrailer vehicle system with time delay ». Mechanical Systems and Signal Processing. vol. 76-77 p. 696-711.
Viet Hung Vu, Zhaoheng Liu, Marc Thomas, Tahvilian Masoud Amir, Bruce Hazel. 2016. « Identification of frequency response functions of a flexible robot as tool-holder for robotic grinding process ». IECON 2016 : 42nd Annual Conference of IEEE Industrial Electronics Society (Florence, Italy, Oct. 24-27, 2016) p. 6347-6352. IEEE.
Viet-Hung Vu, Zhaoheng Liu, Marc Thomas, Wenchao Li, Bruce Hazel. 2016. « Output-only identification of modal shape coupling in a flexible robot by vector autoregressive modeling ». Mechanism and Machine Theory. vol. 97 p. 141-154.
D.-D. Dang, X.-T. Pham. 2016. « Numerical analysis of turbulent convective heat transfer in a rotor-stator configuration ». In Mathematical and Computational Approaches in Advancing Modern Science and Engineering . p. 413-424. Springer International Publishing.
X. T. Pham, N. H. Vu, V. François, J. -C. Cuillière. 2016. « Modeling and numerical simulation of multi-layered fiber-reinforced materials applied for non-rigid parts deformation during assembly process ». Communication lors de la conférence : 7e colloque québécois sur le développement numérique de produits (CAO/FAO) ( Montréal, QC, Canada, 4 mai 2016 )
V. Sabri, S. A. Tahan, X. T. Pham, D. Moreau, S. Galibois. 2016. « Fixtureless profile inspection of non-rigid parts using the numerical inspection fixture with improved definition of displacement boundary conditions ». International Journal of Advanced Manufacturing Technology. vol. 82 , nº 5-8. p. 1343-1352.
Fatemeh Aghazadeh, M. Thomas, A. Tahan. 2016. « Effect of varying cutting parameters on the accuracy of tool wear monitoring in milling process ». CMVA Conference : Covering the Spectrum: From Fundamentals to Future Trends (Toronto, ON, Canada, Oct. 26-28, 2016)
M. Kedadouche, M. Thomas, A. Tahan. 2016. « A comparative study between empirical wavelet transforms and empirical mode decomposition methods: application to bearing defect diagnosis ». Mechanical Systems and Signal Processing. vol. 81 p. 88-107.
Mourad Kedadouche, Marc Thomas, Antoine Tahan. 2016. « Empirical mode decomposition combined with empirical wavelets for extracting bearing frequencies in a noisy environment and early detection of defects ». Advances in Condition Monitoring of Machinery in Non-Stationary Operations: Proceedings of the Fourth International Conference on Condition Monitoring of Machinery in Non-Stationary Operations, CMMNO'2014, Lyon, France December 15-17 (Lyon, France, Dec. 15-17, 2014) p. 151-165. Springer International Publishing.
Iyed Laribi, B. Badri, M. Thomas. 2016. « Online condition monitoring of variable speed bar mills ». CMVA Conference : Covering the Spectrum: From Fundamentals to Future Trends (Toronto, ON, Canada, Oct. 26-28, 2016)
Viet Hung Vu, Badri Bechir, Marc Thomas, Jean Pierre. 2016. « Operational modal analysis on a pump operating at varying speeds: an industrial history case ». Mechanics & Industry. vol. 17 , nº 1. 10 p.
Ehsan Mohseni, Martin Viens, Demartonne R. Franca. 2016. « A model-based study of the effect of semi-elliptical surface notch geometry on the signal of a Split-D eddy current probe ». NDT Canada 2016 (Burlington, ON, Canada, Nov. 15-17, 2016) CINDE.
Alexandre Abid, Dhawal Thakare, Daniel Pereira, Prabu Rajagopal, Julio Fernandes, Pierre Bélanger. 2015. « Guided wave velocity sensitivity to bone mechanical property evolution in cortical-marrow and cortical-trabecular phantoms ». 170th Meeting of the Acoustical Society of America (Jacksonville, FL, USA, Nov. 2-6, 2015)
Pierre Belanger. 2015. « Remnant thickness mapping using high order shear horizontal modes ». ASNT 24th research symposium (Anaheim, CA, USA, Mar. 16-19, 2015) American Society for Nondestructive Testing.
Daniel Pereira, Alexandre Abid, Lucien Diotaveli, Julio Fernandes, Pierre Belanger. 2015. « Axial transmission assessment of trabecular bone at distal radius using guided waves ». 170th Meeting of the Acoustical Society of America (Jacksonville, FL, USA, Nov. 2-6, 2015)
Dhawal R. Thakare, Pierre Belanger, Prabhu Rajagopal. 2015. « Effect of dimensional degradation on ultrasonic guided waves in bone system ». ICU International Congress on Ultrasonics (ICU) (Metz, France, May 11-14, 2015) p. 1131-1134. Elsevier.
Dhawal R. Thakare, Prabhu Rajagopal, Pierre Belanger. 2015. « Ultrasonic guided waves in bone system with degradation ». 170th Meeting of the Acoustical Society of America (Jacksonville, FL, USA, Nov. 2-6, 2015) Acoustical Society of America.
Meysam Hamid Pourian, Philippe Pilvin, Florent Bridier, Philippe Bocher. 2015. « Modeling the elastoplastic behaviors of alpha Ti-alloys microstructure using Cellular Automaton and finite element methods ». Computational Materials Science. vol. 99 p. 33-42.
N. Kamkar, F. Bridier, P. Jedrzejowski, Philippe Bocher. 2015. « Water droplet impact erosion damage initiation in forged Ti-6Al-4V ». Wear. vol. 322-323 p. 192-202.
Kevin McMeekn, Frédéric Sirois, Philippe Bocher, Maxime Tousignant. 2015. « Equivalent permeability model to simplify the nonlinear hysteretic B-H curve in time harmonic FEM simulations of induction heating ». 20th International Conference on the Computation of Electromagnetic Fields (Compumag 2015) (Montréal, QC, Canada, June 28-July 2, 2015) p. 333-334. International Compumag Society.
Mohsen Mokhtabad Amrei, Yves Verreman, Florent Bridier, Denis Thibault, Philippe Bocher. 2015. « Microstructure characterization of single and multipass 13Cr4Ni steel welded joints ». Metallography, Microstructure, and Analysis. vol. 4 , nº 3. p. 207-218.
Mathieu Paquin, Denis Thibault, Philippe Bocher, Jean-Benoît Lévesque, Yves Verreman, Kenji Shinozaki. 2015. « Assessment of cold cracking tests for low transformation temperature martensitic stainless steel multipass welds ». Welding in the World. vol. 59 , nº 4. p. 521-532.
F. Quevedo, N. Vanderesse, P. Bocher, N. Nuño. 2015. « Characterization and simulation of manufacturing irregularities of additive manufactured well-ordered porous materials ». Advanced Manufacturing Canada (AMC 2015) (Montreal, QC, Canada, Nov. 18-19, 2015)
Hugo Robe, Yasser Zedan, Jianqiang Chen, Hossein Monajati, Eric Feulvarch, Philippe Bocher. 2015. « Microstructural and mechanical characterization of a dissimilar friction stir welded butt joint made of AA2024-T3 and AA2198-T3 ». Materials Characterization. vol. 110 p. 242-251.
V. Savaria, H. Monajati, F. Bridier, Philippe Bocher. 2015. « Measurement and correction of residual stress gradients in aeronautical gears after various induction surface hardening treatments ». Journal of Materials Processing Technology. vol. 220 p. 113-123.
J. C. Stinville, F. Bridier, D. Ponsen, P. Wanjara, Philippe Bocher. 2015. « High and low cycle fatigue behavior of linear friction welded Ti-6Al-4V ». International Journal of Fatigue. vol. 70 p. 278-288.
J. C. Stinville, N. Vanderesse, F. Bridier, P. Bocher, T. M. Pollock. 2015. « High resolution mapping of strain localization near twin boundaries in a nickel-based superalloy ». Acta Materialia. vol. 98 p. 29-42.
Matteo Strano, Alessandro Marra, Valerio Mussi, Massimo Goletti, Philippe Bocher. 2015. « Endurance of damping properties of foam-filled tubes ». Materials. vol. 8 , nº 7. p. 4061-4079.
Lotfi Toubal, Philippe Bocher, André Moreau. 2015. « Bimodal dwell-fatigue Weibull distribution of forged titanium IMI 834 ». International Journal of Damage Mechanics. vol. 24 , nº 5. p. 629-645.
Zhengkun Feng, Henri Champliaud. 2015. « Modeling and simulation based on finite element method for electron beam welding process ». 27th European Modeling and Simulation Symposium (EMSS) (Bergeggi, Italy, Sept. 21-23, 2015) p. 79-83. Dime University of Genoa.
Zhengkun Feng, Henri Champliaud. 2015. « Modeling and simulation for pressing process with reconfigurable punch and die ». ASME 2015 Pressure Vessels and Piping Conference (Boston, MA, USA, July 19-23, 2015) American Society of Mechanical Engineers.
M. Saboori, J. Gholipour, H. Champliaud, A. Gakwaya, P. Wanjara, J. Savoie. 2015. « Prediction of burst pressure in multi stage tube hydroforming of aerospace alloys ». ASME Turbo Expo 2015: Turbine Technical Conference and Exposition (GT 2015) (Montreal, QC, Canada, June 15-19, 2015) American Society of Mechanical Engineers (ASME).
S. Sarafan, P. Wanjara, Henri Champliaud, D. Thibault. 2015. « Characteristics of an autogenous single pass electron beam weld in thick gage CA6NM steel ». International Journal of Advanced Manufacturing Technology. vol. 78 , nº 9. p. 1523-1535.
Amir Masoud Tahvilian, Zhaoheng Liu, Henri Champliaud, Bruce Hazel, Marin Lagacé. 2015. « Characterization of grinding wheel grain topography under different robotic grinding conditions using confocal microscope ». International Journal of Advanced Manufacturing Technology. vol. 80 , nº 5. p. 1159-1171.
Fatemeh Mirakhorli, Xinjin Cao, Xuan Tan Pham, Priti Wanjara, Jean-Luc Fihey. 2015. « Hybrid laser-arc welding of cast martensitic stainless steel CA6NM: Post-weld tempered microstructure and mechanical properties ». Conference of metallurgists (COM 2015) (Toronto, ON, Canada, Aug. 23-26, 2015)
Z. Nili Ahmadabadi, Frédéric Laville, Raynald Guilbault. 2015. « An empirical prediction law for quasi-static nail-plywood penetration resistance ». Construction and Building Materials. vol. 88 p. 126-133.
Zahra Nili Ahmadabadi, Frédéric Laville, Raynald Guilbault. 2015. « Study of parameters influencing pneumatic nail-gun noise ». 44th International Congress and Exposition on Noise Control Engineering, INTER-NOISE 2015 (San Francisco, CA, USA, Aug. 9-12, 2015) p. 17-28. The Institute of Noise Control Engineering of the USA, Inc..
Guillaume Corriveau, Raynald Guilbault, Antoine Tahan, R. Sabourin. 2015. « Evaluation of genotypic diversity measurements exploited in real-coded representation ». arXiv. 13 p.
Raynald Guilbault, Sébastien Lalonde, Marc Thomas. 2015. « Modeling and monitoring of tooth fillet crack growth in dynamic simulation of spur gear set ». Journal of Sound and Vibration. vol. 343 p. 144-165.
Mourad Kedadouche, Marc Thomas, Antoine Tahan, Raynald Guilbault. 2015. « Monitoring gears by vibration measurements: Lempel-Ziv complexity and approximate entropy as diagnostic tools ». 4th Colloque Experimental Vibration Analysis, AVE 2014, November 18, 2014 - November 20, 2014 (Blois, France, Nov. 18-20, 2014) EDP Sciences.
Mourad Kedadouche, Marc Thomas, Antoine Tahan, Raynald Guilbault. 2015. « Nonlinear parameters for monitoring gear: comparison between lempel-ziv, approximate entropy, and sample entropy complexity ». Shock and Vibration. vol. 2015 12 p.
Morteza Najjari, Raynald Guilbault. 2015. « Formula derived from particle swarm optimization (PSO) for optimum design of cylindrical roller profile under EHL regime ». Mechanism and Machine Theory. vol. 90 p. 162-174.
Jana D. Abou Ziki, Lucas A. Hof, Rolf Wuthrich. 2015. « The machining temperature during Spark Assisted Chemical Engraving of glass ». Manufacturing Letters. vol. 3 p. 9-13.
F. Charbonneau, L. A. Hof, D. J. Abou Ziki. 2015. « Gas film stability during Spark Assisted Chemical Engraving (SACE) ». Affiche présentée lors de la conférence : Colloque annuel Plasma-Québec 2015 ( Montreal, QC, Canada, June 3-5, 2015 )
L. A. Hof, F. Charbonneau, D. J. Abou Ziki. 2015. « Glass micromachining by Spark Assisted Chemical Engraving (SACE) ». Communication lors de la conférence : Colloque annuel Plasma-Québec 2015 ( Montreal, QC, Canada, June 3-5, 2015 )
L. A. Hof, F. Charbonneau, R. Wüthrich. 2015. « Spark Assisted Chemical Engraving (SACE) - a versatile micro machining technology for microfluidic devices ». Communication lors de la conférence : 98th Canadian Chemistry Conference and Exhibition ( Ottawa, Canada, June 13-17, 2015 )
L. A. Hof, C. Escobedo, J.D. Abou Ziki, R. Wüthrich. 2015. « Additive Manufacturing (AM) through imprinting Gold nanoparticles on Glass Substrates by Spark Assisted Chemical Engraving (SACE) ». Affiche présentée lors de la conférence : 227th ECS Meeting ( Chicago, IL, USA, May 24-28, 2015 )
M. M. Rahman, L. A. Hof, B. Johnston, S. A. Khanoki, D. Pasini, R. Wüthrich. 2015. « Electro-polishing of additive manufactured porous titanium for medical implants ». Affiche présentée lors de la conférence : 227th ECS Meeting ( Chicago, IL, USA, May 24-28, 2015 )
Stéphane Agnard, Zhaoheng Liu, Bruce Hazel. 2015. « Material removal and wheel wear models for robotic grinding wheel profiling ». 2nd Int. Materials, Industrial, and Manufacturing Engineering Conference, MIMEC2015 (Bali, Indonesia, Feb. 4-6, 2015) p. 35-40.
Wenchao Li, Viet-Hung Vu, Zhaoheng Liu, Marc Thomas, Bruce Hazel. 2015. « Automatic structural mode extraction for time-varying structures via vector time-dependent autoregressive model ». International Conference Surveillance 8 (Roanne, France, Oct. 20-21, 2015)
Thomas Santos, Zhaoheng Liu, Bruce Hazel. 2015. « Study and validation testing of the dynamics of a robotic system with flexible links and joints ». 2015 IEEE International Conference on Mechatronics and Automation (ICMA) (Beijing, China, Aug. 2-5, 2015) p. 1891-1897. IEEE.
Viet Hung Vu, Zhaoheng Liu, Marc Thomas, Amir Masoud Tahvilian, Bruce Hazel. 2015. « Dynamic forces identification and modeling of a robotic grinding process ». Surveillance 8 - International Conference (Roanne, France, Oct. 20-12, 2015)
Viet-Hung Vu, Marc Thomas, Zhaoheng Liu, Bruce Hazel. 2015. « Spectrum construction for non statiotionary vibration: application for a working robot ». 4th Colloque Experimental Vibration Analysis, AVE 2014, November 18, 2014 - November 20, 2014 (Blois, France, Nov. 18-20, 2014) EDP Sciences.
D-D. Dang, X. T. Pham. 2015. « Numerical analysis of turbulent convective heat transfer in a rotor-stator configuration ». 23rd Annual Conference of the Computational Fluid Dynamics Society of Canada (CFDSC 2015) (Waterloo, ON, Canada, June 7-12, 2015)
Hugues Lessard, Gilbert Lebrun, Abdelhaq Benkaddour, Xuan-Tan Pham. 2015. « Influence of process parameters on the thermostamping of a [0/90]12 carbon/polyether ether ketone laminate ». Composites Part A: Applied Science and Manufacturing. vol. 70 p. 59-68.
Hong-Den Nguyen, Martin Deshaies, Xuan-Tan Pham. 2015. « Simulation-assisted mold design for forming of thermoplastic PPS/ carbon fiber composites ». 62nd CASI Aeronautics Conference (Montreal, QC, Canada, May 18-21, 2015)
Asmaa Abed, Ahmed Bouzidane, Marc Thomas, Hamou Zahloul, Amina Nemchi. 2015. « Performance characteristics of a new electrorheological valve three-pad hydrostatic squeeze film dampers ». 1st International Conference on Tribology (Turkeytrib'15) (Istanbul, Turkey, Oct. 7-9, 2015)
Hicham AboShighiba, Ahmed Bouzidane, Faiza Ghezal, Marc Thomas, Amina Nemchi, Asmaa Abed. 2015. « Turbulent and inertia effects on the pressure distribution in orifice compensated hydrostatic bearing using numerical simulations via navier stokes ». 1st International Conference on Tribology (Turkeytrib'15) (Istanbul, Turkey, Oct. 7-9, 2015)
Faiza Ghezal, Ahmed Bouzidane, Hicham AboShighiba, Marc Thomas. 2015. « Three-dimensional patterns in a hydrostatic bearing lubricated by ferrofluids ». 1st International Conference on Tribology (Turkeytrib'15) (Istanbul, Turkey, Oct. 7-9, 2015)
Yacine Imaouchen, Rezak Alkama, Marc Thomas. 2015. « Bearing fault detection using motor current signal analysis based on wavelet packet decomposition and Hilbert envelope ». 4th Colloque Experimental Vibration Analysis, AVE 2014, November 18, 2014 - November 20, 2014 (Blois, France, Nov. 18-20, 2014) EDP Sciences.
Yacine Imaouchen, Rezak Alkama, Marc Thomas. 2015. « Complexity based on synchrosqueezing analysis in gear diagnosis ». Mechanics & Industry. vol. 16 , nº 5. 8 p.
Yacine Imaouchen, Mourad Kedadouche, Rezak Alkama, Marc Thomas. 2015. « The envelope-derivative operator for bearing fault detection ». Surveillance 8 - International Conference (Roanne, France, Oct. 20-21, 2015)
Mourad Kedadouche, Marc Thomas, Antoine Tahan. 2015. « A hybrid method combining Teager Kaiser energy operator, empirical mode decomposition and minimum entropy deconvolution for monitoring gears damages ». Mechanics and Industry. vol. 16 , nº 6. 15 p.
Mourad Lamraoui, Mustapha Barakat, Marc Thomas, Mohamed El Badaoui. 2015. « Chatter detection in milling machines by neural networks classification and feature selection ». Journal of Vibration and Control. vol. 21 , nº 7. p. 1251-1266.
Amina Nemchi, Ahmed Bouzidane, Marc Thomas, Asma Abed, Mourad Kedadouche. 2015. « Influence of turbulent flow regime on dynamic behaviour of a rigid rotor on four-pad hydrostatic squeeze film dampers loaded between pads ». 1st International Conference on Tribology (Turkeytrib'15) (Istanbul, Turkey, Oct. 7-9, 2015)
Roger Serra, Luigi Garibaldi, Nuno M. Maia, Marc Thomas. 2015. « Experimental Shock and Vibration Analysis ». Shock and Vibration. vol. 2015 1 p.
Marc Thomas. 2015. « Bearing monitoring : from modelling to feature selection for fault diagnosis ». Surveillance 8 - International Conference (Roanne, France, Oct. 20-21, 2015)
Marc Thomas. 2015. « Développement d’indicateurs de défauts de roulements : de la modélisation à l’expérimentation ». ICM/CIM 2015 (Montréal, QC, Canada, 9-13 mai 2015)
Marc Thomas. 2015. « Développement d’indicateurs de défauts de roulements : de la modélisation à l’expérimentation ». Communication lors de la conférence : Séminaire au LMA-CRNS ( Marseille, France, 10 nov. 2015 )
Lionel Birglen, Benoit Leblanc, Xavier Maldague, Iraj Mantegh, Sylvain Roberge, Martin Viens, Wen-fang Xie. 2015. « Introduction of a robotic system for aerospace manufacturing: The case for non-destructive inspection and beyond ». 62nd CASI Aeronautics Conference (Montreal, QC, Canada, May 19-21, 2015)
H. H. Boukani, S. M. Chentouf, Martin Viens, S.-Antoine Tahan, M. Gagnon. 2015. « The effect of martensitic stainless steel microstructure on the ultrasonic inspection of turbine runner joints ». AIP Conference Proceedings (Boise, ID, USA, July 20-25, 2014) p. 909-916. USA : AIP - American Institute of Physics.
P-C. Ostiguy, M. H. Sherafat, D. R. Franca, N. Bouslama, N. Quaegebeur, A. Maslouhi, L. Lessard, P. Hubert, M. Viens, M. R. Mofakhami, Z. Hajjar, P. Masson. 2015. « Selection of structural features for the systematic study of guided wave propagation and interaction with damage ». Structural health monitoring 2015 : System Reliability for Verification and Implementation (Stanfort, CA, USA, Sept. 1-3, 2015) p. 1973-1980. Destech Publications.
Victor Songmene, Riad Khettabi, Martin Viens, Jules Kouam, Stéphane Hallé, François Morency, Jacques Masounave, Abdelhakim Djebara. 2015. « Nanoparticle measurement, control and characterization: procedure applied to machining and mechanical friction ». «Studies and Research Projects» IRSST. 82 p.
J. Zheng, W. F. Xie, Martin Viens, L. Birglen, I. Mantegh. 2015. « Design of an advanced automatic inspection system for aircraft parts based on fluorescent penetrant inspection analysis ». Insight: Non-Destructive Testing and Condition Monitoring. vol. 57 , nº 1. p. 18-24 and 34.
Pierre Bélanger. 2014. « High order shear horizontal modes for minimum remnant thickness ». Ultrasonics. vol. 54 , nº 4. p. 1078-1087.
Florent Bridier, Jean-Charles Stinville, Nicolas Vanderesse, Patrick Villechaise, Philippe Bocher. 2014. « Microscopic strain and crystal rotation measurement within metallurgical grains ». Materials Structure and Micromechanics of Fracture VII (Brno, Czech Republic, July 1-3, 2013) p. 493-496. Trans Tech Publications Ltd.
Gholam Reza Ebrahimi, Amir Momeni, Mohammad Jahazi, Philippe Bocher. 2014. « Dynamic recrystallization and precipitation in 13Cr super-martensitic stainless steels ». Metallurgical and Materials Transactions A: Physical Metallurgy and Materials Science. vol. 45 , nº 4. 13 p. p. 2219-2231.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault. 2014. « Influence of load spectrum assumptions on the expected reliability of hydroelectric turbines: A case study ». Structural Safety. vol. 50 p. 1-8.
Majid Hoseini, Philippe Bocher, Arash Shahryari, Fereshteh Azari, Jerzy A. Szpunar, Hojatollah Vali. 2014. « On the importance of crystallographic texture in the biocompatibility of titanium based substrate ». Journal of Biomedical Materials Research - Part A. vol. 102 , nº 10. p. 3631-3638.
W. Jomaa, Victor Songmene, Philippe Bocher. 2014. « Surface finish and residual stresses induced by orthogonal dry machining of AA7075-T651 ». Materials. vol. 7 , nº 3. p. 1603-1624.
Walid Jomaa, Monzer Daoud, Victor Songmene, Philippe Bocher, Jean-François Châtelain. 2014. « Identification and validation of Marusich's constitutive law for finite element modeling of high speed machining ». ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014) American Society of Mechanical Engineers (ASME).
Walid Jomaa, Victor Songmene, Philippe Bocher. 2014. « Material behavior modeling during high speed machining of 6061-T6 and 7075-T651 alloys ». Affiche présentée lors de la conférence : Journée des étudiants du REGAL (JER2014) ( Sherbrooke, QC, Canada, Nov. 18, 2014 )
Maxime Lapalme, Majid Hoseini, Philippe Bocher, Alain R. Colle, Martin Levesque. 2014. « Realistic cold expansion finite element model and experimental validations for aluminium alloys ». Experimental Mechanics. vol. 54 , nº 5. p. 841-855.
A. Momeni, G. R. Ebrahimi, Mohammad Jahazi, Philippe Bocher. 2014. « Microstructure evolution at the onset of discontinuous dynamic recrystallization: a physics-based model of subgrain critical size ». Journal of Alloys and Compounds. vol. 587 p. 199-210.
Meysam H. Pourian, Philippe Pilvin, Florent Bridier, Philippe Bocher. 2014. « Heterogeneous elastic behavior of HCP titanium polycrystalline aggregates simulated by cellular automaton and finite element ». Computational Materials Science. vol. 92 p. 468-475.
J. Ruiz-Vargas, N. Siredey-Schwaller, P. Noyrez, S. Mathieu, Philippe Bocher, N. Gey. 2014. « Potential and limitations of microanalysis SEM techniques to characterize borides in brazed Ni-based superalloys ». Materials Characterization. vol. 94 p. 46-57.
Vincent Savaria, Florent Bridier, Philippe Bocher. 2014. « Measuring in-depth residual stress gradients: The challenge of induction hardened parts ». International Conference on Residual Stresses 9 (ICRS 9) (Garmisch-Partenkirchen, Germany, Oct. 7-9, 2012) p. 158-165. Zurich-Durnten, Switzerland : Trans Tech Publications Ltd.
H. Touazine, Mohammad Jahazi, Philippe Bocher. 2014. « Influence of hard turning on microstructure evolution in the subsurface layers of Inconel 718 ». ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014) American Society of Mechanical Engineers (ASME).
S. Mojarad Farimani, J. Gholipour, Henri Champliaud, J. Savoie, P. Wanjara. 2014. « Numerical and experimental study of preforming stage in tube hydroforming ». Material Forming ESAFORM 2014 (Espoo, Finland, May 7-9, 2014) p. 1132-1138. Trans Tech Publications Ltd.
Zhengkun Feng, Henri Champliaud. 2014. « Analyses of profile radial-axial ring rolling process based on explicit finite element method ». American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP (Anaheim, CA, USA, July 20-24, 2014) American Society of Mechanical Engineers (ASME).
Zhengkun Feng, Henri Champliaud. 2014. « FEM analysis of radial-axial profile ring rolling process ». 26th European Modeling and Simulation Symposium, EMSS 2014 (Bordeaux, France, Sept. 10-12, 2014) p. 295-300. Dime University of Genoa.
Zhengkun Feng, Henri Champliaud. 2014. « Using pyramidal three-roll bending process to improve the quality of seemed cylinders ». ASME 2013 International Mechanical Engineering Congress and Exposition : November 15-21, 2013, San Diego, California, USA. (San Diego, CA, USA, Nov. 15-21, 2013 ) New York, NY, USA : ASME.
Van Ngan Lê, Henri Champliaud. 2014. « Safety factor of welded-plate beams based on finite element linear buckling analysis ». Proceedings of the IASTED International Conference on Modelling, Simulation and Identification, MSI 2014 (Banff, AB, Canada, July 16-18, 2014) p. 51-57. Acta Press.
S. Mojarad, H. Champliaud, J. Gholipour, J. Savoie, P. Wanjara. 2014. « Load path optimization in tube hydroforming ». Canadian Aeronautics and Space Journal = Journal Aéronautique et Spatial du Canada. vol. 60 , nº 3. p. 82-89.
M. Saboori, Henri Champliaud, J. Gholipour, A. Gakwaya, J. Savoie, P. Wanjara. 2014. « Evaluating the flow stress of aerospace alloys for tube hydroforming process by free expansion testing ». International Journal of Advanced Manufacturing Technology. vol. 72 , nº 9-12. p. 1275-1286.
Sheida Sarafan, Priti Wanjara, Henri Champliaud, Denis Thibault, Louis Mathieu. 2014. « Evaluation of electron beam welded AISI 415 stainless steel ». ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE) (Montreal, QC, Canada, Nov. 14-20, 2014) American Society of Mechanical Engineers (ASME).
Hoang Quan Tran, Henri Champliaud, Zhengkun Feng, Thien-My Dao. 2014. « Dynamic FE analysis for reducing the flat areas of formed shapes obtained by roll bending process ». ASME 2013 International Mechanical Engineering Congress and Exposition : November 15-21, 2013, San Diego, California, USA. (San Diego, CA, USA, Nov. 15-21, 2013 ) New York, NY, USA : ASME.
Quan Hoang Tran, Henri Champliaud, Zhengkun Feng, Thien My Dao. 2014. « FE study for reducing forming forces and flat end areas of cylindrical shapes obtained by the roll-bending process ». Journal of Mechanics Engineering and Automation. vol. 4 , nº 6. p. 467-475.
Quan Hoang Tran, Henri Champliaud, Zhengkun Feng, Thien-My Dao. 2014. « Analysis of the asymmetrical roll bending process through dynamic FE simulations and experimental study ». International Journal of Advanced Manufacturing Technology. vol. 75 , nº 5-8. p. 1233-1244.
F. Mirakhorli, X. Cao, Tan Pham, P. Wanjara, Jean-Luc Fihey. 2014. « Hybrid fiber laser-arc welding of 10-mm thick CA6NM stainless steel ». Materials Science and Technology Conference and Exhibition 2014, MS and T 2014 (Pittsburgh, PA, USA, Oct. 12-16, 2014) p. 1891-1900. Association for Iron and Steel Technology, AISTECH.
T. Kidar, M. Thomas, M. El Badaoui, R. Guilbault. 2014. « Control of phases by ESPRIT and WLSE methods for the early detection of gear cracks ». Mechanics & Industry. vol. 15 , nº 6. p. 487-495.
Thameur Kidar, Marc Thomas, Mohamed Elbadaoui, Raynald Guilbault. 2014. « Phase Monitoring by ESPRIT with Sliding Window and Hilbert Transform for Early Detection of Gear Cracks ». Advances in Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the third International Conference on Condition Monitoring of Machinery in Non-Stationary Operations CMMNO 2013 (Ferrara, Italy, ) p. 287-299. Springer Berlin Heidelberg.
Morteza Najjari, Raynald Guilbault. 2014. « Edge contact effect on thermal elastohydrodynamic lubrication of finite contact lines ». Tribology International. vol. 71 p. 50-61.
Morteza Najjari, Raynald Guilbault. 2014. « Modeling the edge contact effect of finite contact lines on subsurface stresses ». Tribology International. vol. 77 p. 78-85.
R. Wüthrich, J.D. Abou Ziki, L. A. Hof, P. Matoorian, G. Cusanelli, D. Lüthi. 2014. « Glass micro-machining by contact glow discharge electrolysis ». 65th Annual Meeting of the International Society of Electrochemistry (Lausanne, Switzerland, Aug. 31 - Sept. 05, 2014)
Marc Thomas, Zhaoheng Liu, F. Léonard. 2014. « Compte rendu 32ième séminaire sur la vibration des machines : ACVM-CIRI, 29-31 octobre 2014 ». Montréal, QC, Canada : ACVM.
Joel Lessard, Pascal Bigras, Zhaoheng Liu, Bruce Hazel. 2014. « Characterization, modeling and vibration control of a flexible joint for a robotic system ». Journal of Vibration and Control. vol. 20 , nº 6. p. 943-960.
Z. Li, V. -H. Vu, Z. Liu, M. Thomas, B. Hazel. 2014. « Basis function selection criterion for modal monitoring of non stationary systems ». 32nd CMVA (Canadian Machinery Vibration Association) Annual Seminar and the 4th Int. Congress on Engineering of Industrial Risks (Montreal, QC, Canada, Oct. 29-31, 2014)
Farzad Rafieian, François Girardin, Zhaoheng Liu, Marc Thomas, Bruce Hazel. 2014. « Angular analysis of the cyclic impacting oscillations in a robotic grinding process ». Mechanical Systems and Signal Processing. vol. 44 , nº 1-2. p. 160-176.
Farzad Rafieian, Bruce Hazel, Zhaoheng Liu. 2014. « Regenerative instability of impact-cutting material removal in the grinding process performed by a flexible robot arm ». 6th CIRP International Conference on High Performance Cutting, HPC2014 p. 406-411. Elsevier.
Farzad Rafieian, Bruce Hazel, Zhaoheng Liu. 2014. « Vibro-impact dynamics of material removal in a robotic grinding process ». International Journal of Advanced Manufacturing Technology. vol. 73 , nº 5-8. p. 949-972.
R. Keivani, Mohammad Jahazi, Tan Pham, A. R. Khodabandeh, M. R. Afshar. 2014. « Predicting residual stresses and distortion during multisequence welding of large size structures using FEM ». International Journal of Advanced Manufacturing Technology. vol. 73 , nº 1-4. p. 409-419.
Phuong Nguyen-Tri, Rachid El Aidani, Étienne Leborgne, Tan Pham, Toan Vu-Khanh. 2014. « Chemical ageingaging of a polyester nonwoven membrane used in aerosol and drainage filter ». Polymer Degradation and Stability. vol. 101 , nº 1. p. 71-80.
S. Adewusi, M. Thomas, V. H. Vu, W. Li. 2014. « Modal parameters of the human hand-arm using finite element and operational modal analysis ». Mechanics & Industry. vol. 15 , nº 6. p. 541-549.
Surajdeen Adewusi, Marc Thomas, Viet Hung Vu. 2014. « Natural frequencies of the human hand-arm system using finite element method and experimental modal analysis ». Transaction on control and mechanical systems. vol. 3 , nº 1. p. 11-18.
A. Bouzidane, M. Thomas. 2014. « Linear and nonlinear behavior analysis of a flexible shaft supported by hydrostatic squeeze film dampers ». International Journal of Engineering Research and Applications. vol. 4 , nº 1. p. 311-316.
A. Bouzidane, F. Ghezali, M. Thomas. 2014. « Performance characteristics of an orifice compensated three-pad hydrostatic squeeze film dampers ». 5th International Symposium on Aircraft Materials ACMA2014, Marrakech - Morocco, April 23-26, 2014 (Marrakech, Morocco, Apr. 23-26, 2014)
F. Ghezali, A. Bouzidane, M. Thomas. 2014. « Influence of flow regime in a recess on the pressure field of an orifice compensated hydrostatic bearing ». 5th International Symposium on Aircraft Materials ACMA2014, Marrakech - Morocco, April 23-26, 2014 (Marrakech, Morocco, Apr. 23-26, 2014)
M. Kedadouche, M. Thomas, A. Tahan. 2014. « Cyclostationarity applied to acoustic emission and development of a new indicator for monitoring bearing defects ». Mechanics & Industry. vol. 15 , nº 6. p. 467-476.
M. Kedadouche, Marc Thomas, Antoine Tahan. 2014. « Monitoring machines by using a hybrid method combining MED, EMD, and TKEO ». Advances in Acoustics and Vibration. vol. 2014
Mourad Kedadouche, Marc Thomas, Antoine Tahan. 2014. « Empirical mode decomposition of acoustic emission for early detection of bearing defects ». Advances in Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the third International Conference on Condition Monitoring of Machinery in Non-Stationary Operations CMMNO 2013 (Ferrara, Italy, ) p. 367-377. Springer Berlin Heidelberg.
M. Lamraoui, Marc Thomas, M. El Badaoui. 2014. « Cyclostationarity approach for monitoring chatter and tool wear in high speed milling ». Mechanical Systems and Signal Processing. vol. 44 , nº 1-2. p. 177-198.
M. Lamraoui, Marc Thomas, M. El Badaoui, F. Girardin. 2014. « Indicators for monitoring chatter in milling based on instantaneous angular speeds ». Mechanical Systems and Signal Processing. vol. 44 , nº 1-2. p. 72-85.
Viet Hung Vu, B. Badri, M. Thomas. 2014. « Vibration analysis and monitoring on a pump in operation ». 32nd CMVA (Canadian Machinery Vibration Association) Annual Seminar and the 4th Int. Congress on Engineering of Industrial Risks (Montreal, QC, Canada, Oct. 29-31, 2014) Canadian Machinery Vibration Association.
Viet Hung Vu, Marc Thomas. 2014. « Uncertainties on modal parameters by operational modal analysis ». Mechanics and Industry. vol. 15 , nº 2. p. 153-158.
Viet Hung Vu, Marc Thomas, F. Lafleur. 2014. « Harmonic and modal frequency discrimination in time domain operational modal analysis ». Mechanics and Industry. vol. 15 , nº 1. p. 29-37.
H. H. Boukani, Martin Viens, S.-Antoine Tahan, M. Gagnon. 2014. « On the performance of nondestructive testing methods in the hydroelectric turbine industry ». 27th IAHR Symposium on Hydraulic Machinery and Systems (IAHR 2014) (Montreal, QC, Canada, Sept. 22-26, 2014) IOP Publishing.
P. Masson, A. Maslouhi, P. Micheau, N. Quaegebeur, L. Lessard, P. Hubert, M. Viens, S. Kruger, M. R. Mofakhami, J. Pinsonnault, Z. Hajjar, P-C. Ostiguy, M. Sherafat, D. Ramos Franca. 2014. « Characterization of guided wave propagation in aircraft structures ». Affiche présentée lors de la conférence : 1er Forum du Réseau national | 7e Forum du CRIAQ ( Montreal, QC, Canada, Apr. 16-17, 2014 )
Victor Songmene, Riad Khettabi, Martin Viens, Jules Kouam, Stéphane Hallé, François Morency, Jacques Masounave, Abdelhakim Djebara. 2014. « Mesure, contrôle et caractérisation des nanoparticules : Procédure appliquée à l'usinage et au frottement mécanique ». Montréal, Québec, Canada. «Études et recherches» IRSST. 93 p.
Melissa Anderson, Javad Gholipour, Florent Bridier, Philippe Bocher, Mohammad Jahazi, Jean Savoie, Priti Wanjara. 2013. « Improving the formability of stainless steel 321 through multistep deformation for hydroforming applications ». Transactions of the Canadian Society for Mechanical Engineering. vol. 37 , nº 1. p. 39-52.
Amir Ansaripour, Hossein Monajatizadeh, Philippe Bocher, Davoud Asefi. 2013. « Evaluation of recovery and recrystallization in cold rolled low carbon steel by magnetic hysteresis loop measurements ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 225-233. Warrendale, PA, USA : Association for Iron and Steel Technology.
N. Barka, Philippe Bocher, J. Brousseau. 2013. « Sensitivity study of hardness profile of 4340 specimen heated by induction process using axisymmetric modeling ». International Journal of Advanced Manufacturing Technology. vol. 69 , nº 9-12. p. 2747-2756.
Noureddine Barka, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau. 2013. « Effects of material properties fornon-equilibrium conditions in induction heating process ». Environmental and Materials Engineering (Seoul, Korea, Dec. 9-10, 2012) p. 496-503. Clausthal-Zellerfeld, Germany : Trans Tech Publications Ltd.
Noureddine Barka, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau. 2013. « Explorative study and prediction of overtemperingregion of disc heated by induction process using 2D axisymmetric model and experimental tests ». Materials and Manufacturing Research (Hong Kong, China, Dec. 19-20, 2012) p. 259-265. Trans Tech Publications.
Noureddine Barka, Abdel Jelil Khelalfa, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau. 2013. « Effect of skin depth on hardness profile of gear heated by induction using 2D model ». Environmental and Materials Engineering (Seoul, Korea, Dec. 9-10, 2012) p. 884-890. Clausthal-Zellerfeld, Germany : Trans Tech Publications Ltd.
Noureddine Barka, Abderrazak El Ouafi, Philippe Bocher, Jean Brousseau, Ahmed Chebak. 2013. « Explorative study and prediction of overtempering region of disc heated by induction process using 2D axisymmetric model and experimental tests ». Materials Engineering for Advanced Technologies (ICMEAT 2012) (Xiamen, China, Dec. 27-28, 2012) p. 417-423. Scientific.net.
N. Boutana, P. Bocher, M. Jahazi. 2013. « Discrepancy between fatigue and dwell-fatigue behavior of near alpha titanium alloys simulated by cellular automata ». International Journal of Fatigue. vol. 51 p. 49-56.
M. Gagnon, Antoine Tahan, Philippe Bocher, D. Thibault. 2013. « On the fatigue reliability of hydroelectric Francis runners ». 5th International Conference on Fatigue Design, Fatigue Design 2013 (Senlis, France, Nov. 27-28, 2013) p. 565-574.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault. 2013. « A probabilistic model for the onset of High Cycle Fatigue (HCF) crack propagation: Application to hydroelectric turbine runner ». International Journal of Fatigue. vol. 47 p. 300-307.
A. Gariepy, F. Bridier, M. Hoseini, Philippe Bocher, C. Perron, M. Levesque. 2013. « Experimental and numerical investigation of material heterogeneity in shot peened aluminium alloy AA2024-T351 ». Surface and Coatings Technology. vol. 219 p. 15-30.
A. Gariepy, S. Larose, C. Perron, Philippe Bocher, M. Levesque. 2013. « On the effect of the orientation of sheet rolling direction in shot peen forming ». Journal of Materials Processing Technology. vol. 213 , nº 6. p. 926-938.
A. Gariepy, S. Larose, C. Perron, Philippe Bocher, M. Levesque. 2013. « On the effect of the peening trajectory in shot peen forming ». Finite Elements in Analysis and Design. vol. 69 p. 48-61.
W. Jomaa, Victor Songmene, Philippe Bocher. 2013. « On residual stress changes after orthogonal machining of induction hardened AISI 4340 steel ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 94-103. Warrendale, PA, USA : Association for Iron and Steel Technology.
N. Kamkar, Florent Bridier, Philippe Bocher, P. Jedrzejowski. 2013. « Water droplet erosion mechanisms in rolled Ti-6Al-4V ». Wear. vol. 301 , nº 1-2. p. 442-448.
Rabih Kassab, Henri Champliaud, Philippe Bocher, Jacques Lanteigne, Van Ngan Lê. 2013. « Strain variations of AISI 4340 steel undergoing metallurgical transformations during induction hardening heat treatment ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 774-783. Warrendale, PA, USA : Association for Iron and Steel Technology.
Benjamin Larregain, Nicolas Vanderesse, Florent Bridier, Philippe Bocher, Patrick Arkinson. 2013. « Method for accurate surface temperature measurements during fast induction heating ». Journal of Materials Engineering and Performance. vol. 22 , nº 7. p. 1907-1913.
A. R. Maldar, G. R. Ebrahimi, Meysam Haghshenas, M. Jahazi, P. Bocher. 2013. « Thermomechanical characterization of Mg-9Al-1Zn alloy using power dissipation maps ». Journal of Materials Engineering and Performance. vol. 22 , nº 11. p. 3306-3314.
A. Moreau, L. Toubal, Philippe Bocher, M. Humbert, E. Uta, N. Gey. 2013. « Evaluation of macrozone dimensions by ultrasound and EBSD techniques ». Materials Characterization. vol. 75 p. 115-128.
M. Paquin, D. Thibault, Philippe Bocher, Y. Verreman. 2013. « Study on cold cracking test methods for low carbon soft-martensitic stainless steel flux cored arc welding ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 733-744. Warrendale, PA, USA : Association for Iron and Steel Technology.
J. Ruiz-Vargas, N. Siredey-Schwaller, Philippe Bocher, A. Hazotte. 2013. « First melting stages during isothermal brazing, of Ni/BNi-2 couples ». Journal of Materials Processing Technology. vol. 213 , nº 12. p. 2074-2080.
D. Shahriari, A. Zolfaghari, Mohammad Jahazi, Philippe Bocher. 2013. « Development of an expert system to characterize weld defects identified by ultrasonic testing ». American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP (Paris, France, July 14-18, 2013) New York, NY, USA : American Society of Mechanical Engineers.
J. Yi, M. Gharghouri, Philippe Bocher, M. Medraj. 2013. « Distortion and residual stress measurements of induction hardened AISI 4340 discs ». Materials Chemistry and Physics. vol. 142 , nº 1. p. 248-258.
Zhengkun Feng, Henri Champliaud. 2013. « FEM analysis of mecano-welding process for manufacturing cylinders ». Sheet Metal 2013 (Belfast, Ireland, Mar. 25-27, 2013) p. 444-451. Trans Tech Publications Ltd.
Zhengkun Feng, Henri Champliaud. 2013. « Modeling and simulation of hot radial-axial ring rolling process for producing power plant parts ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 677-686. Warrendale, PA, USA : Association for Iron and Steel Technology.
Zhengkun Feng, Henri Champliaud. 2013. « Modelling and simulation of radial ring rolling process based on finite element analyses ». American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP (Paris, France, July 14-18, 2013) New York, NY, USA : American Society of Mechanical Engineers.
Zhengkun Feng, Henri Champliaud, Louis Mathieu, Michel Sabourin. 2013. « Modeling and simulation of optimal blank design and hot pressing process for manufacturing large francis turbines blades from very thick plates ». American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP (Paris, France, July 14-18, 2013) New York, NY, USA : American Society of Mechanical Engineers.
Zhengkun Feng, Henri Champliaud, Louis Mathieu, Michel Sabourin, Van Ngan Lê. 2013. « Investigation of pressing process for large and thick blades of Francis turbines ». Congrès français de mécanique 2013 : du 26 au 30 août 2013 Bordeaux (Bordeaux, France, Aug. 26-30, 2013) Association Française de Mécanique.
Zhengkun Feng, Henri Champliaud, Michel Sabourin, Sebastien Morin. 2013. « Optimal blank design based on finite element method for blades of large Francis turbines ». Simulation Modelling Practice and Theory. vol. 36 p. 11-21.
Mathieu Gendron, Eric Boudreault, Bruce Hazel, Henri Champliaud, Tan Pham. 2013. « Temperature profile optimization in a new robotic local induction heat treatment process ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 766-773. Warrendale, PA, USA : Association for Iron and Steel Technology.
Van Ngan Lê, Henri Champliaud. 2013. « Safety factor of beam-column structures based on finite element linear buckling analysis ». Congrès français de mécanique 2013 : du 26 au 30 août 2013 Bordeaux (Bordeaux, France, Aug. 26-30, 2013) Association Française de Mécanique.
S. Mojarad Farimani, Henri Champliaud, J. Gholipour, J. Savoie, P. Wanjara. 2013. « Numerical and experimental study of tube hydroforming for aerospace applications ». The Current State-of-the-Art on Material Forming: Numerical and Experimental Approaches at Different Length-Scales (Aveiro, Portugal, Apr. 22-24, 2013) p. 1779-1786. Zurich-Durnten, Switzerland : Trans Tech Publications Ltd.
M. Saboori, J. Gholipour, Henri Champliaud, A. Gakwaya, J. Savoie, P. Wanjara. 2013. « Development of an inverse method for material characterization ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 694-701. Warrendale, PA, USA : Association for Iron and Steel Technology.
M. Saboori, J. Gholipour, Henri Champliaud, A. Gakwaya, J. Savoie, P. Wanjara. 2013. « Effect of material model on finite element modeling of aerospace alloys ». The Current State-of-the-Art on Material Forming: Numerical and Experimental Approaches at Different Length-Scales (Aveiro, Portugal, Apr. 22-24, 2013) p. 151-156. Zurich-Durnten, Switzerland : Trans Tech Publications Ltd.
S. Sarafan, P. Wanjara, Henri Champliaud, L. Mathieu, J. Lanteigne. 2013. « Characteristics of electron beam welded CA6NM ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 720-732. Warrendale, PA, USA : Association for Iron and Steel Technology.
A. M. Tahvilian, Henri Champliaud, Zhaoheng Liu, B. Hazel. 2013. « Study of workpiece temperature distribution in the contact zone during robotic grinding process using finite element analysis ». 8th CIRP Conference on Intelligent Computation in Manufacturing Engineering, ICME 2012 (Ischia, Italy, July 18-20, 2012) p. 205-210. Elsevier.
Amir Masoud Tahvilian, Henri Champliaud, Zhaoheng Liu, Bruce Hazel. 2013. « Influence of grit shape and cutting edge of material removal mechanism of a single abrasive in flexible robotic grinding ». ASME 2013 International Mechanical Engineering Congress and Exposition : November 15-21, 2013, San Diego, California, USA (San Diego, CA, USA, Nov. 15-21, 2013 ) New York, NY, USA : ASME.
Amir Masoud Tahvilian, Zhaoheng Liu, Henri Champliaud, Bruce Hazel. 2013. « Experimental and finite element analysis of temperature and energy partition to the workpiece while grinding with a flexible robot ». Journal of Materials Processing Technology. vol. 213 , nº 12. p. 2292-2303.
M. Tahvilian, Henri Champliaud, Zhaoheng Liu, B. Hazel. 2013. « Chop formation analysis of single grit cutting action in robotic grinding processes ». 52nd Annual Conference of Metallurgists (COM 2013) (Montreal, QC, Canada, Oct. 27-31, 2013) Montreal, QC, Canada : CIM The Candian Institute of Mining.
Dominique Thuot, Zhaoheng Liu, Henri Champliaud, Julien Beaudry, Pierre-Luc Richard, Michel Blain. 2013. « Remote robotic underwater grinding system and modeling for rectification of hydroelectric structures ». Robotics and Computer-Integrated Manufacturing. vol. 29 , nº 1. p. 86-95.
Quan H. Tran, Henri Champliaud, Zhengkun Feng, Jamel Salem, Thien-My Dao. 2013. « Heat-assisted roll-bending process dynamic simulation ». International Journal of Modelling and Simulation. vol. 33 , nº 1. p. 54-62.
Tan Pham, G. Pradinc, X. Cao, J. L. Fihey. 2013. « Modeling of moving heat sources using meshless element free galerkin method ». ASM Proceedings of the International Conference: Trends in Welding Research (Chicago, IL, USA, June 4-8, 2012) p. 746-751. OH, USA : ASM International.
Guillaume Corriveau, Raynald Guilbault, Antoine Tahan, Robert Sabourin. 2013. « Review of phenotypic diversity formulations for diagnostic tool ». Applied Soft Computing. vol. 13 , nº 1. p. 9-26.
Raynald Guilbault. 2013. « A simplified thermal analysis of elastohydrodynamic contacts ». Journal of Tribology. vol. 135 , nº 2.
Raynald Guilbault, Sebastien Lalonde, Marc Thomas. 2013. « Corrigendum to "Nonlinear damping calculation in cylindrical gear dynamic modeling" [J. Sound Vib. 331/9 (2012) 2110–2128] ». Journal of Sound and Vibration. vol. 332 , nº 20. p. 5240.
M. Kedadouche, T. Kidar, M. Thomas, A. Tahan, M. El Badaoui, R. Guilbault. 2013. « A comparative study between acoustic emission and vibration for early detection of gear cracks ». Surveillance 7 : international conference : October 29-30, 2013, Chartres, France (Chartres, France, Oct. 29-30, 2013) France : Institute of Technology.
Mourad Kedadouche, Thameur Kidar, Marc Thomas, Antoine Tahan, Mohamed El Badaoui, Raynald Guilbault. 2013. « Combining EMD and Lempel-Ziv complexity for early detection of gear cracks ». Surveillance 7 : international conference : October 29-30, 2013, Chartres, France (Chartres, France, Oct. 29-30, 2013) Chartres, France : Institute of Technology.
T. Kidar, M. Thomas, M. El Badaoui, R. Guilbault. 2013. « Diagnosis of gear faults by cyclostationnarity ». Surveillance 7 : international conference : October 29-30, 2013, Chartres, France (Chartres, France, Oct. 29-30, 2013) Chartres, France : Institute of Technology.
Thameur Kidar, Marc Thomas, Mohamed El Badaoui, Raynald Guilbault. 2013. « Control of phases by Esprit and WLSE methods for the early detection of gear cracks ». CIRI 2013, 3ème Congrès International sur l’Ingénierie des Risques Industriels (Reims, France, July 3-5, 2013) Reims, France : Université de Reims Champagne-Ardenne.
Thameur Kidar, Marc Thomas, Raynald Guilbault, El Badaoui Mohamed. 2013. « Comparison between the efficiency of L.M.D and E.M.D algorithms for early detection of gear defects ». Mechanics and Industry. vol. 14 , nº 2. p. 121-127.
Stéphane Agnard, Zhaoheng Liu, Bruce Hazel. 2013. « Modeling and experimental work on robotic grinding tool profiling through tool orientation control for repair of high curvature surfaces ». Materials Science and Technology Conference and Exhibition 2013, MS and T 2013 (Montreal, QC, Canada, Oct. 27-31, 2013) p. 712-719. Warrendale, PA, USA : Association for Iron and Steel Technology.
T. Santos, Zhaoheng Liu, B. Hazel. 2013. « Étude des propriétés vibratoires d'un système robotique en opération de meulage par modélisation multi-corps flexibles ». 21ème Congrès français de mécanique (Bordeaux, France, 26-30 août 2012) Paris, France : Association Française de Mécanique.
Quang Hien Bui, Xuan Tan Pham, Mario Fafard. 2013. « Modelling of microstructure effects on the mechanical behavior of aluminium tubes drawn with different reduction areas ». International Journal of Plasticity. vol. 50 p. 127-145.
K. Kouwonou, X. T. Pham, G. Lebrun. 2013. « Modeling and characterization of thermoplastic composites peek/carbon ». Proceedings of the 19th International Conference on Composite Materials-ICCM19 (Montreal, QC, Canada, July 28-Aug. 2, 2013)
Hugues Lessard, Gilbert Lebrun, Xuan-Tan Pham. 2013. « Experimental evaluation of the thermo-stamping process for a 3d composite part made of unidirectional cf/peek prepregs ». 45th ISTC (Wichita, KS, USA, Oct. 21-24, 2013) SAMPE.
Xuan-Tan Pham. 2013. « Analyse thermique de Rosenthal par la méthode meshless element free Galerkin ». Communication lors de la conférence : Séminaire "Modélisation avancée des cuves d'électrolyse et efficacité énergétique'' de la Chaire de recherche industrielle CRSNG/Alcoa sur la modélisation avancée des cuves d'électrolyse et l'efficacité énergétique, Université Laval ( Québec, QC, Canada, 16 mai 2013 )
Xuan-Tan Pham. 2013. « Simulation numérique du soudage par éléments finis avec Sysweld ». Communication lors de la conférence : Symposoud 2013. Ensembles soudés: de la conception à la fabrication ( Varennes, QC, Canada, 30-31 mai 2013 )
Xuan-Tan Pham. 2013. « Two-dimensional rosenthal moving heat source analysis using the meshless element free Galerkin method ». Numerical Heat Transfer; Part A: Applications. vol. 63 , nº 11. p. 807-823.
G. Pradinc, X-T. Pham, X. Cao, J-L. Fihey, L. Mathieu. 2013. « An experimentally assisted numerical simulation of metal forming for thick and heavy plates by line heating ». Communication lors de la conférence : Materials Science & Technology Conference and Exhibition 2013 (MS&T'13) ( Montreal, QC, Canada, Oct. 27-31, 2013 )
V. Sabri, S.-Antoine Tahan, X. T. Pham, H. Radvar-Esfahlan, B. Louhichi, A. M. Tahvilian. 2013. « Fixtureless profile inspection of non-rigid parts ». Proceedings of International Conference on Computers and Industrial Engineering, CIE (Hong Kong, China, Oct. 16-18, 2013) p. 86-97. Curran Associates Inc..
S. Adewusi, S. Rakheja, P. Marcotte, Marc Thomas. 2013. « Distributed vibration power absorption of the human hand-arm system in different postures coupled with vibrating handle and power tools ». International Journal of Industrial Ergonomics. vol. 43 , nº 4. p. 363-374.
S. Adewusi, M. Thomas, V. H. Vu, W. Li. 2013. « Modal parameters of the human hand-arm using finite element and operational modal analysis ». CIRI 2013, 3ème Congrès International sur l’Ingénierie des Risques Industriels (Reims, France, July 3-5, 2013) Reims, France : Université de Reims Champagne-Ardenne.
Luana Batista, Bechir Badri, Robert Sabourin, Marc Thomas. 2013. « A classifier fusion system for bearing fault diagnosis ». Expert Systems with Applications. vol. 40 , nº 17. p. 6788-6797.
A. Bouzidane, Marc Thomas. 2013. « Nonlinear Dynamic Analysis of a Rigid Rotor Supported by a Three-Pad Hydrostatic Squeeze Film Dampers ». Tribology Transactions. vol. 56 , nº 5. p. 717-727.
A. Bouzidane, Marc Thomas. 2013. « Nonlinear dynamic behavior of a flexible shaft supported by smart hydrostatic squeeze film dampers ». Journal of Tribology. vol. 135 , nº 3.
Ahmed Bouzidane, Marc Thomas. 2013. « Nonlinear behavior analysis of a flexible shaft supported by hydrostatic squeeze film dampers ». Congrès français de mécanique 2013 : du 26 au 30 août 2013 Bordeaux (Bordeaux, France, Aug. 26-30, 2013) Association Française de Mécanique.
Mourad Kedadouche, Marc Thomas, Antoine Tahan. 2013. « Cyclostationarity applied to acoustic emission and development of a new indicator for monitoring bearing defects ». CIRI 2013, 3ème Congrès International sur l’Ingénierie des Risques Industriels (Reims, France, July 3-5, 2013) Reims, France : Université de Reims Champagne-Ardenne.
V. H. Vu, M. Thomas, F. Lafleur, L. Marcouiller. 2013. « Towards an automatic spectral and modal identification from operational modal analysis ». Journal of Sound and Vibration. vol. 332 , nº 1. p. 213-227.
Viet Hung Vu, Marc Thomas. 2013. « Uncertainties on modal parameters by operational modal analysis ». 21ème Congrès français de mécanique 2013 : du 26 au 30 août 2013 Bordeaux (Bordeaux, France, Aug. 26-30, 2013) Association Française de Mécanique.
Sylvie Nadeau, Michèle Bouchard, Maximilien Debia, Nathalie DeMarcellis-Warin, Stéphane Hallé, Victor Songmene, Marie-Christine Therrien, Kevin Wilkinson, Barthelemy Ateme-Nguema, Genevieve Dufour, André Dufresne, Julien Fatisson, Sami Haddad, Madjid Hadioui, Jules Kouam, François Morency, Robert Tardif, Martin Viens, Scott Weichenthal, Claude Viau, Michel Camus. 2013. « EquiNanos: innovative team for nanoparticle risk management ». Nanomedicine : Nanotechnology, Biology and Medicine. vol. 9 , nº 1. p. 22-24.
Baoguang Xu, W. F. Xie, Martin Viens, Ehsan Mohseni, Lionel Birglen, Iraj Mantegh. 2013. « Intelligent eddy current crack detection system design based on neuro-fuzzy logic ». Proceedings of the The NDT in Canada 2013 Conference in conjunction with the International Workshop on Smart Materials & Structures, SHM and NDT for the Energy Industry (Calgary, AB, Canada, Oct. 7-10, 2013)
J. Zheng, W. F. Xie, Martin Viens, L. Birglen, I. Mantegh. 2013. « Design of advanced automatic inspection system for turbine blade FPI analysis ». Review of Progress in Quantitative Nondestructive Evaluation (Denver, CO, USA, July 15-20, 2012) p. 612-619. USA : American Institute of Physics.
Melissa Anderson, Philippe Bocher, Javad Gholipour, Mohammad Jahazi, Jean Savoie, Priti Wanjara. 2012. « Increasing the hydroformability of stainless steel 321 by multistep processing ». Proceedings of the 14th International Conference on Metal Forming, METAL FORMING 2012 (Krakow, Poland, Sept. 16-19, 2012) p. 1243-1246. Krakow, Poland : Wiley-VCH Verlag.
Noureddine Barka, Ahmed Chebak, Abderrazakel Ouafi, Philippe Bocher, Jean Brousseau. 2012. « Sensitivity study of temperature profile of 4340 spur gear heated by induction process using 3D model ». Mechanical and Aerospace Engineering (Paris, France, July 7-8, 2012) p. 736-741. Trans Tech Publications.
Noureddine Barka, Abderrazak El Ouafi, Ahmed Chebak, Philippe Bocher, Jean Brousseau. 2012. « Study of induction heating process applied to internal gear using 3D model ». Mechanical and Aerospace Engineering (Paris, France, July 7-8, 2012) p. 730-735. Trans Tech Publications.
M. Gagnon, Antoine Tahan, Philippe Bocher, D. Thibault. 2012. « The role of high cycle fatigue (HCF) onset in Francis runner reliability ». 26th IAHR Symposium on Hydraulic Machinery and Systems (Beijing, China, Aug. 19-23, 2012) UK : IOP Publishing Ltd..
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault. 2012. « On the stochastic simulation of hydroelectric turbine blades transient response ». Mechanical Systems and Signal Processing. vol. 32 p. 178-187.
A. Gariepy, J. Cyr, A. Levers, C. Perron, P. Bocher, M. Lévesque. 2012. « Potential applications of peen forming finite element modelling ». Advances in Engineering Software. vol. 52 p. 60-71.
N. Gey, P. Bocher, E. Uta, L. Germain, M. Humbert. 2012. « Texture and microtexture variations in a near-α titanium forged disk of bimodal microstructure ». Acta Materialia. vol. 60 , nº 6-7. p. 2647-2655.
N. Gey, Philippe Bocher, E. Uta, M. Humbert, J. Gilgert. 2012. « How texture and microtexture influence dwell fatigue lifetime in forged IMI834 titanium alloys ». Ti 2011 - Proceedings of the 12th World Conference on Titanium (Beijing, China, June 19-24, 2011) p. 879-882. Beijing, China : Science Press.
Majid Hoseini, Philippe Bocher, Fereshteh Azari, Hojatollah Vali, Jerzy A. Szpunar. 2012. « Effects of grain size and texture on the biocompatibility of commercially pure titanium ». 16th International Conference on Textures of Materials (Mumbai, India, Dec. 12-17, 2011 ) p. 822-825. Trans Tech Publications Ltd.
Majid Hoseini, Florent Bridier, Philippe Bocher, Hojatollah Vali, Jerzy A. Szpunar. 2012. « Thermal stability and grain growth behavior of ultrafine grained commercially pure titanium fabricated by equal channel angular pressing ». Ti 2011 - Proceedings of the 12th World Conference on Titanium (Beijing, China, June 19-24, 2011) p. 666-670. Beijing, China : Science Press.
Majid Hoseini, Meysam Hamid Pourian, Florent Bridier, Hojatollah Vali, Jerzy A. Szpunar, Philippe Bocher. 2012. « Thermal stability and annealing behaviour of ultrafine grained commercially pure titanium ». Materials Science and Engineering A. vol. 532 p. 58-63.
J. Ruiz-Vargas, N. Siredey-Schwaller, N. Gey, P. Bocher, A. Hazotte. 2012. « Microstructure development during isothermal brazing of Ni/BNi-2 couples ». Journal of Materials Processing Technology. vol. 213 , nº 1. p. 20-29.
Vincent Savaria, Florent Bridier, Philippe Bocher. 2012. « Computational quantification and correction of the errors induced by layer removal for subsurface residual stress measurements ». International Journal of Mechanical Sciences. vol. 64 , nº 1. p. 184-195.
H. Champliaud, Van Ngan Lê. 2012. « Beginning learning principles of finite element method with heat conduction ». Proceedings of the 5th World Universities Forum : Reinventing the university in a time of crisis (Rhodes Island, Greece, Jan. 8-10, 2012) Rhodes Island, Greece : Common Ground Publishing.
Zhengkun Feng, Henri Champliaud. 2012. « Investigation of non-kinematic conical roll bending process with conical rolls ». Simulation Modelling Practice and Theory. vol. 27 p. 65-75.
Zhengkun Feng, Henri Champliaud. 2012. « Modeling and simulation of mecano-welding process for cylinders ». Proceedings of the ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (Chicago, IL, USA, Aug. 12-15, 2012) New York, NY, USA : ASME.
Zhengkun Feng, Henri Champliaud. 2012. « Numerical simulation of mecano-welding process for cylinder manufacturing ». ASME 2012 Pressure Vessels and Piping Conference, PVP 2012 (Toronto, ON, Canada, July 15-19, 2012) p. 1055-1060. New York, N.Y., USA : American Society of Mechanical Engineers.
Zhengkun Feng, Henri Champliaud, Michel Sabourin, Sébastien Morin. 2012. « Modeling and simulation based on inverse finite element method for unfolding large and thick blades of Francis turbines ». 24th European Modeling and Simulation Symposium, EMSS 2012 (Vienna, Austria, Sept.19-21, 2012) p. 27-31. Italy : DIPTEM.
Zhengkun Feng, Henri Champliaud, Michel Sabourin, Sebastien Morin. 2012. « Simulation of blank design for blades of francis turbines ». ASME 2012 International Mechanical Engineering Congress and Exposition, IMECE 2012 (Houston, TX, USA, Nov. 9-15, 2012) p. 23-30. New York, N.Y., USA : American Society of Mechanical Engineers.
Rabih Kamal Kassab, Henri Champliaud, Van Ngan Lê, Jacques Lanteigne, Marc Thomas. 2012. « Experimental and finite element analysis of a t-joint welding ». Journal of Mechanics Engineering and Automation. vol. 2 , nº 7. p. 411-421.
Van Ngan Lê, Henri Champliaud. 2012. « A teaching approach for enhancing structural design aspects in basic engineering courses ». Proceedings of the 5th World Universities Forum : Reinventing the university in a time of crisis (Rhodes Island, Greece, Jan. 8-10, 2012) Rhodes Island, Greece : Common Ground Publishing.
Van Ngan Lê, Henri Champliaud. 2012. « Finite element simulations for comparing three manhole designs for horizontal mills ». Proceedings of the IASTED International Conference on Modelling and Simulation, MS 2012 (Banff, AB, Canada, July 3-5, 2012 ) p. 192-197. Calgary, Canada : Acta Press.
M. Saboori, Henri Champliaud, J. Gholipour, A. Gakwaya, J. Savoie, P. Wanjara. 2012. « Study of true stress-strain curve after necking for application in ductile fracture criteria in tube hydroforming of aerospace material ». Material Forming ESAFORM 2012 (Erlangen, Germany, Mar. 14-16, 2012) p. 95-100. Trans Tech Publications Ltd.
Hoang Quan Tran, Henri Champliaud, Zhengkun Feng, Thien-My Dao. 2012. « Analytical modeling and Fe simulation for analyzing applied forces during roll bending process ». ASME 2012 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (Chicago, IL, USA, Aug. 12-15, 2012) p. 207-215. American Society of Mechanical Engineers.
Hoang Quan Tran, Henri Champliaud, Zhengkun Feng, Thien-My Dao. 2012. « Dynamic analysis of a workpiece deformation in the roll bending process by FEM simulation ». 24th European Modeling and Simulation Symposium, EMSS 2012 (Vienna, Austria, Sept.19-21, 2012) p. 477-482. Italy : DIPTEM.
Guillaume Corriveau, Raynald Guilbault, Antoine Tahan, Robert Sabourin. 2012. « Review and study of genotypic diversity measures for real-coded representations ». IEEE Transactions on Evolutionary Computation. vol. 16 , nº 5. p. 695-710.
Raynald Guilbault. 2012. « Influence of thermal shear localization on elastohydrodynamic contacts ». Tribology and Design II (Kos, Greece, Sept. 3-5, 2012) p. 3-16. Billerica, MA : Wit Press.
Raynald Guilbault, Sébastien Lalonde, Marc Thomas. 2012. « Nonlinear damping calculation in cylindrical gear dynamic modeling ». Journal of Sound and Vibration. vol. 331 , nº 9. p. 2110-2128.
Thameur Kidar, Marc Thomas, Mohamed Elbadaoui, Raynald Guilbault. 2012. « Application of Time Descriptors to the Modified Hilbert Transform of Empirical Mode Decomposition for Early Detection of Gear Defects ». Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the Second International Conference "Condition Monitoring of Machinery in Non-Stationnary Operations" CMMNO’2012 (Hammamet, Tunisia, Mar. 26-28, 2012) p. 471-479. Berlin, Heidelberg : Springer Berlin Heidelberg.
Thameur Kidar, Marc Thomas, Raynald Guilbault, Mohamed El Badaoui. 2012. « Comparison between the efficiency of LMD and EMD algorithms for early detection of gear defects ». 3ième édition du colloque national sur l'analyse vibratoire expérimentale (AVE 2012) (Blois, France, Nov. 20-21, 2012)
M. Najjari, R. Guilbault. 2012. « Edge correction in the elastohydrodynamic lubrication of finite line contact ». International Conference on Mechanical Engineering and Mechatronics (ICMEM'12) (Ottawa, ON, Canada, Aug. 16-18, 2012) p. 76.71-76.78. Ottawa, ON, Canada : Avestia Publishing.
Benoit Lacroix, Zhaoheng Liu, Patrice Seers. 2012. « A comparison of two control methods for vehicle stability control by direct yaw moment ». 2011 International Conference on Applied Mechanics, Materials and Manufacturing, ICAMMM (Shenzen, China, Nov. 18-20, 2011) p. 203-217. Trans Tech Publications.
J. Lessard, Pascal Bigras, Zhaoheng Liu, B. Hazel. 2012. « Vibration control and experimental investigation of a robotic system with flexible joints ». Proceedings of the 6th Asian Conference on Multibody Dynamics (Shanghai, China, Aug. 26-30, 2012) Beijing, China : The Chinese society of theoretical and applied mechanics.
S. Adewusi, Marc Thomas, V. H. Vu. 2012. « Natural frequencies of the hand-arm system using finite element method ». 4th American Conference on Human Vibration (CHV) (Hartford, CO, USA, June 13-15, 2012) UCONN Health Center ; Natural Sciences and Engineering Research Council of Canada (NSERC).
B. Badri, Marc Thomas, S. Sassi. 2012. « The envelop shock detector: A new method for processing impulsive signals ». International Journal of COMADEM. vol. 15 , nº 3. p. 29-38.
B. Badri, Marc Thomas, S. Sassi. 2012. « Variable drive frequency effect on spindle dynamic behavior in high speed machining ». 2nd conference on Condition Monitoring of Machinery in Non-Stationary Operations (CMMNO) (Hammamat, Tunisia, Mar. 2012) p. 547-554. Natural Sciences and Engineering Research Council of Canada (NSERC).
Luana Batista, Bechir Badri, Robert Sabourin, Marc Thomas. 2012. « Detecting bearing defects under high noise levels: A classifier fusion approach ». 38th Annual Conference on IEEE Industrial Electronics Society, IECON 2012 (Montreal, QC, Canada, Oct. 25-28, 2012) p. 3880-3886. Washington, DC : IEEE Computer Society.
Ahmed Bouzidane, Marc Thomas. 2012. « Non linear transient response of a flexible shaft controlled by electro-rheological hydrostatic squeeze film dampers ». Condition Monitoring of Machinery in Non-Stationary Operations : Proceedings of the Second International Conference "Condition Monitoring of Machinery in Non-Stationnary Operations" CMMNO’2012 (Hammamet, Tunisia, Mar. 26–28, 2012) p. 33-40. Springer Berlin Heidelberg.
Y. Imaouchen, R. Alkama, M. Thomas. 2012. « Application of wavelet packet transform for outer race bearing defect detection ». 3rd International Conference on the Image and Signal Processing and their Applications (ISPA'12) (Mostaganem, Algeria, Dec. 2-4, 2012)
Y. Imaouchen, R. Alkama, Marc Thomas. 2012. « Wavelet packet transform of induction motor stator current for bearing fault detection ». International Conference on Electrical Mechanical Engineering (ICEE) (Skikda, Algeria, Nov. 2012)
Y. Imaouchen, Marc Thomas, R. Alkama. 2012. « Détection de défauts de roulements en combinant de l'enveloppe de Hilbert au Kurtogram ». Deuxième Conférence Internationale sur la Maintenance, la Gestion, la Logistique et l’Electrotechnique (CIMGLE) (Oran, Algeria, 19-21 nov. 2012)
M. Kedadouche, Marc Thomas, Antoine Tahan. 2012. « Monitoring bearings by acoustic emission: a comparative study with vibration techniques for early detection ». 30th Canadian Machinery Vibration Association (CMVA) (Niagara Falls, ON, Canada, Oct. 24-26, 2012) The Canadian Machinery Vibration Association.
M. Lamraoui, M. Barakat, Marc Thomas, M. El Badaoui. 2012. « Envelope multiband resonance filtering and neural networks for the chatter detection in high speed milling machines ». Research and Innovation for Transport Systems of the Future (RITF) (Paris, France, Nov. 13-15, 2012) ASTech Paris Region.
M. Lamraoui, Marc Thomas, M. El Badaoui, F. Girardin. 2012. « Cyclostationarity analysis of instantaneous angular speeds for monitoring chatter in high speed milling ». 38th Annual Conference on IEEE Industrial Electronics Society, IECON 2012 (Montreal, QC, Canada, Oct. 25-28, 2012) p. 3868-3873. Washington, DC : IEEE Computer Society.
Patrick Lyonnet, Marc Thomas, Rosario Toscano. 2012. « Fiabilité, diagnostic et maintenance prédictive des systèmes ». Paris : Éd. Tec & doc. 377 p.
Yulan Sun, Marc Thomas. 2012. « Smart electrorheological dynamic absorber for controlling torsional vibrations of rotors ». Applied Mechanics In The Americas 2012 : proceedings of PACAM XII (Port of Spain, Trinidad, Jan 02-06, 2012) The American Academy of Mechanics.
Marc Thomas, Antoine Tahan, M. Kedadouche. 2012. « Comparison of acoustic emission and vibration measurements for early detection of bearing damages ». Research and Innovation for Transport Systems of the Future (RITF) (Paris, France, Nov. 15, 2012)
V. H. Vu, Marc Thomas, F. Lafleur. 2012. « Harmonic and modal frequency discrimination by operational modal analysis in time domain ». 18th symposium on Vibrations, Shocks and Noise (Paris, France, July 3-5, 2012)
P. Masson, N. Quaegebeur, P. Micheau, A. Maslouhi, M. Viens, L. Lessard, P. Hubert, S. Kruger. 2012. « Characterization of guided wave propagation in aircraft structures ». Recherche et Innovation pour les Transports du Futur (RITF 2012) (Paris, France, Nov.12-16, 2012)
Yann Pasco, Olivier Robin, Pierre Bélanger, Alain Berry, Srivatsa Rajan. 2011. « Multi-input multi-output feedforward control of multi-harmonic gearbox vibrations using parallel adaptive notch filters in the principal component space ». Journal of Sound and Vibration. vol. 330 , nº 22. p. 5230-5244.
N. Barka, Philippe Bocher, J. Brousseau, P. Arkinson. 2011. « Effect of dimensional variation on induction process parameters using 2D simulation ». THERMEC 2011 Supplement (Quebec City, QC, Canada, Aug. 1-5, 2011) p. 395-400. Germany : Trans Tech Publications.
Alessandro Candeo, Christophe Ducassy, Philippe Bocher, Fabrizio Dughiero. 2011. « Multiphysics modeling of induction hardening of ring gears for the aerospace industry ». IEEE Transactions on Magnetics. vol. 47 , nº 5. p. 918-921.
Vincent Savaria, Majid Hoseini, Florent Bridier, Philippe Bocher, Patrick Arkinson. 2011. « On the measurement of residual stress in induction hardened parts ». Residual Stresses VIII (Riva del Garda, Trento, Italy, June 26-28, 2010) p. 431-436.
Denis Thibault, Philippe Bocher, Marc Thomas, Jacques Lanteigne, Pierre Hovington, Patrice Robichaud. 2011. « Reformed austenite transformation during fatigue crack propagation of 13%Cr-4%Ni stainless steel ». Materials Science and Engineering A. vol. 528 , nº 21. p. 6519-6526.
Zhengkun Feng, Henri Champliaud. 2011. « Modeling and simulation of asymmetrical three-roll bending process ». Simulation Modelling Practice and Theory. vol. 19 , nº 9. p. 1913-1917.
Zhengkun Feng, Henri Champliaud. 2011. « Modeling and simulation of mecano-welding process for tubular sections ». ASME International Mechanical Engineering Congress & Exposition (IMECE) (Denver, CO, USA, Nov. 11-17, 2011) p. 11-14. ASME.
Zhengkun Feng, Henri Champliaud. 2011. « Three-stage process for improving roll bending quality ». Simulation Modelling Practice and Theory. vol. 19 , nº 2. p. 887-898.
A. W. Hulskamp, J. W. Van Wingerden, T. Barlas, Henri Champliaud, G. A. M. Van Kuik, Harald E. N. Bersee, M. Verhaegen. 2011. « Design of a scaled wind turbine with a smart rotor for dynamic load control experiments ». Wind Energy. vol. 14 , nº 3. p. 339-354.
Abdelmajid Lajmi, Henri Champliaud, Van Ngan Lê. 2011. « Computation of the maximum torque of a cap liner using a power-law friction and finite element analysis ». Packaging Technology and Science. vol. 24 , nº 2. p. 103-121.
Van Ngan Lê, Henri Champliaud. 2011. « Finite element analysis of spring back strain energy of metal sheet coils ». A world of engineering simulation industrial needs, best practice, visions for the future ; NWC 2011, NAFEMS World Congress, 23-26 May, Boston, USA (Boston, MA, USA, May 23-26, 2011)
Mehdi Saboori, J. Gholipour, Henri Champliaud, A. Gakwaya, J. Savoie, P. Wanjara. 2011. « Prediction of burst pressure using a decoupled ductile fracture criterion for tube hydroforming of aerospace alloys ». 14th International Esaform Conference on Material Forming (Esaform) (Belfast, Ireland, Apr. 27-29, 2011) p. 301-306. Melville, NY, USA : American Institute of Physics.
Quan Hoang Tran, Henri Champliaud, Zhengkun Feng, Thien-My Dao. 2011. « FE simulation of heat assisted roll bending process for manufacturing large and thick high strength steel axisymmetric parts ». IASTED International Conference on Modelling, Simulation, and Identification (MSI) (Pittsburgh, PA, USA, Nov. 7-9, 2011) p. 322-329. Calgary, Canada : ACTA Press.
Raynald Guilbault. 2011. « A fast correction for elastic quarter-space applied to 3D modeling of edge contact problems ». Journal of Tribology. vol. 133 , nº 3. 10 p.
Sébastien Lalonde, Raynald Guilbault. 2011. « Prediction of thin-rimmed gear crack propagation from a factorial design approach ». Fatigue and Fracture of Engineering Materials and Structures. vol. 34 , nº 7. p. 470-486.
Kwok-Wai Chung, Zhaoheng Liu. 2011. « Nonlinear analysis of chatter vibration in a cylindrical transverse grinding process with two time delays using a nonlinear time transformation method ». Nonlinear Dynamics. vol. 66 , nº 4. p. 441-456.
François Girardin, Farzad Rafieian, Zhaoheng Liu, Marc Thomas, Bruce Hazel. 2011. « Using angular speed measurement with hall effect sensors to observe grinding operation with flexible robot ». International Conference Surveillance 6 (Compiègne, France, Oct. 25-26, 2011)
Bruce Hazel, Farzad Rafieian, Zhaoheng Liu. 2011. « Impact-cutting and regenerative chatter in robotic grinding ». ASME International Mechanical Engineering Congress & Exposition (Denver, CO, USA, Nov. 11-17, 2011) p. 349-359. ASME.
J. Lessard, G. Swiatek, Zhaoheng Liu, B. Hazel. 2011. « Flexible multibody dynamics and effects of nonlinear joint stiffness for vibration analysis in a robotic grinding process ». Multibody Dynamics : ECCOMAS Thematic Conference (Bruxelles, Belgique, July 4-7, 2011)
F. Mokdad, V. H. Vu, Marc Thomas, F. Rafieian, Zhaoheng Liu, B. Hazel. 2011. « Online modal analysis of a flexible robot during grinding ». 4th International operational modal analysis conference (IOMAC) (Istanbul, Turkey, May 9-11, 2011)
Q. H. Bui, Tan Pham. 2011. « Modeling of microstructure effects on the mechanical behavior of ultrafine-grained nickels processed by hot isostatic pressing ». International Journal of Mechanical Sciences. vol. 53 , nº 10. p. 812-826.
Q. H. Bui, Tan Pham, M. Fafard. 2011. « A self-consistent model predicting the mechanical behavior of cold-draw 6063 aluminium tubes ». COM 2011 : Conference of Metallurgists (Montreal, Canada, Oct. 2-5, 2011)
Houcine Ayari, Marc Thomas, Sylvie Doré. 2011. « A design of experiments for statistically predicting risk of adverse health effects on drivers exposed to vertical vibrations ». International Journal of Occupational Safety and Ergonomics. vol. 17 , nº 3. p. 221-232.
Bechir Badri, Marc Thomas, Sadok Sassi. 2011. « A shock filter for bearing slipping detection and multiple damage diagnosis ». International Journal of Mechanics. vol. 5 , nº 4. p. 318-326.
Bechir Badri, Marc Thomas, Sadok Sassi. 2011. « A shock filter of a vibratory signal for damage detection ». Computational Engineering in Systems Application : Proceedings of International Conference on Energy, Environment, Economics, Devices, Systems, Communications, Computers (Iasi, Romania, July 1-3, 2011) p. 13-17. IAASAT Press.
A. Bouzidane, Marc Thomas, F. Ghezali. 2011. « Dynamic behavior of a rigid rotor supported by a new three-pad hydrostatic squeeze film damper ». International Conference Surveillance 6 (Compiègne, France, Oct. 25-26, 2011)
F. Lafleur, V. H. Vu, Marc Thomas. 2011. « Case study of operational modal analysis (OMA) of a large hydroelectric generator ». Proceedings of the 29th Seminar on Machinery Vibration (St John, Nouveau-Brunswick, Canada, ) Canadian Machinery Vibration Association.
M. Lamraoui, Marc Thomas, M. El Badaoui, I. Zaghbani, Victor Songmene. 2011. « New indicators based on cyclostationarity approach for machining monitoring ». International Conference Surveillance 6 (Compiègne, France, Oct. 25-26, 2011) p. 27.
Mourad Lamraoui, Marc Thomas, Mohamed El Badaoui, Imed Zaghbani, Victor Songmene. 2011. « The angular kurtosis and power : new tools for machining monitoring ». DINAME : The 14th International Symposium on Dynamic Problems of Mechanics (Sao Paulo, Brazil, Mar. 13-18, 2011) p. 494-511. Sao Sebastiao : ABCM.
Yulan Sun, Marc Thomas. 2011. « Control of torsional rotor vibrations using an electrorheological fluid dynamic absorber ». Journal of Vibration and Control. vol. 17 , nº 8. p. 1253-1264.
V. H. Vu, M. Thomas, A. A. Lakis, L. Marcouiller. 2011. « Short-Time Autoregressive (STAR) modeling for operational modal analysis of non-stationary vibration ». In Vibration and Structural Acoustics Analysis : Current Research and Related Technologies . p. 59-77. Springer.
V. H. Vu, Marc Thomas, F. Lafleur. 2011. « Case study of operational modal analysis (OMA) of a large hydroelectric generator ». 4th International operational modal analysis conference (IOMAC) (Istanbul, Turkey, May 9-11, 2011)
Viet Hung Vu, Marc Thomas, François Lafleur. 2011. « Operational modal monitoring of high power hydro-electrical generators ». Proceedings of IOMAC (International Operational Modal Analysis Conference) 2011 (Istanbul, Turkey, May 9-11, 2011)
Viet Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2011. « Operational modal analysis by updating autoregressive model ». Mechanical Systems and Signal Processing. vol. 25 , nº 3. p. 1028-1044.
Viet Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2011. « Spectrum and operational modal analysis with vector autoregressive models ». In Mechanical vibrations: types, testing and analysis . p. 57-93. Nova Science Publishers, Inc..
Viet-Hung Vu, Marc Thomas, François Lafleur. 2011. « Operational modal monitoring of high power hydro-electrical generators ». International Conference Surveillance 6 (Compiègne, France, Oct. 25-26, 2011)
I. Zaghbani, M. Lamraoui, V. Songmene, M. Thomas, M. El Badaoui. 2011. « Robotic high speed machining of aluminum alloys ». High Speed Machining : The 4th International Conference on High Speed Machining (ICHSM’2010) (Guangzhou, Guangdong, China, Oct. 9-10, 2010) p. 584-589. Trans Tech Publications.
C. A. C. Alba, Martin Viens, X.-W. Tu. 2011. « Development of an image acquisition and processing system for automation of fluorescent penetrant inspection (FPI) ». 58th Aeronautics Conference and AGM (AERO 2011) (Montreal, Canada, Apr. 26-28, 2011) Kanata, Canada : Canadian Aeronautics and Space Institute.
L. A. Généreux, Martin Viens, G. Lebrun. 2011. « Comparison of ultrasonic testing and infrared thermography for the detection of machining defects in composite materials ». Proceedings of the American Society for Composites--Twenty-Sixth Technical Conference (Montréal, Canada, Sept. 26-28, 2011) Lancaster, Penn., USA : DEStech Publications Inc..
Martin Viens, N. Fournier, S. Carpentier. 2011. « Les défis NDT en aéronautique ». Communication lors de la conférence : Atelier Organisé dans le Cadre du Colloque Aérotechnique ( Montréal, QC, Canada, 15 mars 2011 )
P. Belanger, P. Cawley. 2010. « Feasibility of guided wave diffraction tomography within the born approximation ». 36th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) (Kingston, RI, USA, July 26-31, 2009) p. 121-128.
Pierre Bélanger, Peter Cawley, Francesco Simonetti. 2010. « Guided wave diffraction tomography within the born approximation ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 57 , nº 6. p. 1405-1418.
M. Anderson, J. Gholipour, Philippe Bocher, F. Bridier, J. Savoie, P. Wanjara. 2010. « Formability extension of aerospace alloys for tube hydroforming applications ». International Journal of Material Forming. vol. 3 , nº Suppl. 1. p. 303-306.
N. Bastajib, N. Boutana, P. Bocher, M. Jahazi. 2010. « Application of cellular automata method to simulate the hot deformation behavior of a dual phase titanium alloy ». Technische Mechanik. vol. 30 , nº 1-3. 14 p.
Alessandro Candeo, Philippe Bocher, Fabrizio Dughiero. 2010. « Multiphysics modeling of induction hardening of ring gears for the aerospace industry ». 14th Biennial IEEE Conference on Electromagnetic Field Computation (CEFC 2010) (Chicago, IL, USA, May 09-12, 2010) IEEE.
Martin Gagnon, Antoine Tahan, Philippe Bocher, Denis Thibault. 2010. « Impact of startup scheme on Francis runner life expectancy ». 25th IAHR Symposium on Hydraulic Machinery and Systems (Timisoara, Romania, 20–24 Sept. 2010) p. 12107. London, UK : Institute of Physics Publishing.
Denis Thibault, Philippe Bocher, Marc Thomas, Michael Gharghouri, Marjolaine Coté. 2010. « Residual stress characterization in low transformation temperature 13%Cr-4%Ni stainless steel weld by neutron diffraction and the contour method ». Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing. vol. 527 , nº 23. p. 6205-6210.
Lotfi Toubal, Philippe Bocher, André Moreau, Daniel Levesque. 2010. « Macroregion size measurements in bimodal titanium forgings using two-dimensional autocorrelation method ». Metallurgical and Materials Transactions a-Physical Metallurgy and Materials Science. vol. 41A , nº 3. p. 744-750.
O. Charrette, Marc Thomas, Henri Champliaud. 2010. « Effet des contraintes résiduelles de soudage sur les paramètres modaux de plaques minces ». XVII ème Symposium Vibration, Chocs et Bruits (VCB) (Écully, France, 15-17 juin 2010)
Zhengkun Feng, Henri Champliaud. 2010. « Analyses of non-kinematic conical roll bending process with conical rolls ». ASME 2010 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference (IDETC / CIE) (Montréal, Québec, Canada, Aug.15–18, 2010) p. 121-130. New York, NY, USA : American Society of Mechanical Engineers.
Zhengkun Feng, Henri Champliaud. 2010. « Comparison between numerical simulation and experimentation of roll bending process with three asymmetrical cylindrical rolls ». ASME 2010 International Mechanical Engineering Congress and Exposition (IMECE) (Vancouver, Canada, Nov. 12-18, 2010)
A. W. Hulskamp, Henri Champliaud, J. W. Van Wingerden, T. Barlas, Harald E. N. Bersee, G. A. M. Van Kuik, M. Verhaegen. 2010. « Smart dynamic rotor control : part 1, design of a smart rotor ». 3rd Conference Torque 2010 : the science of making torque from wind (FORTH, Heraklion, Crete, Greece, June 28-30, 2010)
Rabih Kassab, Henri Champliaud, Jacques Lanteigne, Van Ngan Lê, Marc Thomas. 2010. « Finite element modeling of a welded T-joint ». Proceedings of the Canadian Society of Mechanical Engineering Forum (Victoria, B.C, Canada, June 7-9, 2010)
Abdelmajid Lajmi, Henri Champliaud, Van Ngan Lê. 2010. « Pressure and temperature dependent static friction model for an elastomer cap liner based on experiments ». Fifth International Conference on Advances in Mechanical Engineering and Mechanics (Hammamet, Tunisia, Dec. 18-20, 2010)
Van Ngan Lê, Henri Champliaud. 2010. « Finite element simulation of forces in strips tying metal sheet coils ». 30th IASTED Conference on Modelling, Identification, and Control (AsiaMIC) (Phuket, Thailand, November 24-26, 2010) p. 74-79. Calgary, Canada : Acta Press.
Van Ngan Lê, Henri Champliaud, Françoise Marchand, Patrick Terriault, Jean Arteau. 2010. « Effective learning of buckling of columns in engineering programs ». Communication lors de la conférence : XI International Conference on Engineering and Technology Education (INTERTECH) ( Ilheus, Bahia, Brazil, Mar. 7-10, 2010 )
Van Ngan Lê, Henri Champliaud, Françoise Marchand, Patrick Terriault, Jean Arteau. 2010. « Effective learning of buckling of columns in engineering programs ». Proceedings of international conference on engineering and technology education (Ilheus, Bahia, Brazil, Mar. 7-10, 2010) p. 143-147.
Mehdi Saboori, Henri Champliaud, J. Gholipour Baradari, A. Gakwaya, J. Savoie. 2010. « Analytical evaluation and finite element simulation of material characteristics in tube hydroforming of aerospace alloys ». Communication lors de la conférence : International Conference on Advances in Materials and Processing Technologies ( Paris, France, Oct. 24-27, 2010 )
Guillaume Corriveau, Raynald Guilbault, Antoine Tahan. 2010. « Genetic algorithms and finite element coupling for mechanical optimization ». Advances in Engineering Software. vol. 41 , nº 3. 5 p. p. 422-426.
Raynald Guilbault. 2010. « A fast correction for traction-free surface of elastic quarter-space ». 3rd International Conference on Tribology and Design (Algarve, Portugal, May 11-13, 2010) p. 37-48. WITPress.
Jianhua Chen, Zhaoheng Liu. 2010. « Modeling and parameter identification of a tractor semitrailer/driver closed-loop system using the Simulated Annealing (SA) optimization approach ». IEEE International Conference on Information and Automation (ICIA) (Harbin, Heilongjiang, China, June 20-23, 2010) p. 222-227. Piscataway, NJ : Institute of Electrical and Electronics Engineers Computer Society.
Grzegorz Swiatek, Zhaoheng Liu, Bruce Hazel. 2010. « Dynamic simulation and configuration dependant modal identification of a portable flexible-link and flexible-joint robot ». Proceedings of the 28th Seminar on Machinery Vibration (Québec, Québec, Canada, Oct. 27-29, 2010) p. 189-206. Canadian Machinery Vibration Association (CMVA).
Béchir Badri, Marc Thomas, Sadok Sassi, I. Zaghbani, V. Songméné. 2010. « Surveillance des roulements des machines d’usinage hautes vitesses (UHV) ». Proceedings of the 28th Seminar on Machinery Vibration (Québec, Québec, Canada, Oct. 27-29, 2010) p. 197-216. Canadian Machinery Vibration Association (CMVA).
Béchir Badri, Marc Thomas, Sadok Sassi, Imed Zaghbani, Victor Songmene. 2010. « Étude du comportement des roulements dans les rotors tournant à haute vitesse ». Revue Internationale sur l'Ingénierie des Risques Industriels. vol. 3 , nº 1. 16 p.
M. Lamraoui, Marc Thomas, M. El Badaoui, I. Zaghbani, V. Songméné. 2010. « Le Kurtosis angulaire : un nouvel outil de diagnostic ». Proceedings of the 28th Seminar on Machinery Vibration (Québec, Québec, Canada, Oct. 27-29, 2010) p. 217-240. Canadian Machinery Vibration Association (CMVA).
M. Lamraoui, Marc Thomas, M. El Badaoui, Imed Zaghbani. 2010. « Le Kurtoisis angulaire comme outil de diagnostic ». XVII ème Symposium Vibration, Chocs et Bruits (VCB) (Écully, France, 15-17 juin 2010)
Farid Mabrouki, Marc Thomas, M. Genest, A. Fahr. 2010. « Numerical modeling of vibrothermography based on plastic deformation ». NDT & E International. vol. 43 , nº 6. p. 476-483.
Patrice Seers, P. Terrier, Antoine Tahan, Marc Thomas. 2010. « Case Study : hybrid vehicles : the Honda insight and Toyota Prius : transition towards the automobile of the future? ». In Sustainable Development in Mechanical Engineering : Case Studies in Applied Mechanics . p. 83-109. Cambridge Scholars Publishing.
Yulan Sun, Marc Thomas, Jacques Masounave. 2010. « A quasi-Bingham model for predicting electrorheological fluid behaviour ». Multidiscipline Modeling in Materials and Structures. vol. 6 , nº 1. p. 141-165.
Viet Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2010. « Short time autoregressive model for Time-Modal monitoring of non stationary systems ». Proceedings of the 28th Seminar on Machinery Vibration (Québec, Québec, Canada, Oct. 27-29, 2010) p. 207-222. Canadian Machinery Vibration Association (CMVA).
Viet-Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2010. « Online time-modal monitoring of non stationnary systems ». Revue Internationale sur l'Ingénierie des Risques Industriels. vol. 3 , nº 1. p. 45-65.
P. Belanger, P. Cawley. 2009. « Feasibility of low-frequency straight-ray guided wave tomography ». Proceedings of the 35th Annual Review of Progress in Quantitative Nondestructive Evaluation (Chicago, IL, USA, July 22-25, 2008) p. 153-160. AIP.
Pierre Bélanger, Alain Berry, Yann Pasco, Olivier Robin, Yves St-Amant, Srivatsa Rajan. 2009. « Multi-harmonic active structural acoustic control of a helicopter main transmission noise using the principal component analysis ». Applied Acoustics. vol. 70 , nº 1. p. 153-164.
Pierre Bélanger, Peter Cawley. 2009. « Feasibility of low frequency straight-ray guided wave tomography ». NDT and E International. vol. 42 , nº 2. p. 113-119.
Yann Pasco, Olivier Robin, Pierre Bélanger, Alain Berry. 2009. « MiMO feedforward control of multi-harmonics gearbox vibrations using parallel adaptive notch filters in the principle component space ». Active09 (Ottawa, ON, Canada, Aug. 20-22, 2009) p. 223-236. Institute of Noise Control Engineering.
Philippe Bocher, F. Bridier, L. Toubal, N. Boutana, E. Uta, N. Gey, M. Humbert. 2009. « Dwell-fatigue in near alpha titanium alloys: A multiscale, interdisciplinary challenge ». 12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009) p. 1481-1486. International Congress on Fracture.
L. Hacini, Van Ngan Lê, Philippe Bocher. 2009. « Evaluation of residual stresses induced by robotized hammer peening by the contour method ». Experimental Mechanics. vol. 49 , nº 6. p. 775-783.
M. Humbert, A. Moreau, E. Uta, N. Gey, Philippe Bocher, C. Bescond. 2009. « Analysis of backscattered ultrasound amplitude of Ti-5.8Al-4Sn-3.5Zr-0.7Nb-0.5Mo-0.3Si samples in terms of their microstructures and local textures ». Acta Materialia. vol. 57 , nº 3. p. 708-714.
Denis Thibault, Philippe Bocher, Marc Thomas. 2009. « Residual stress and microstructure in welds of 13%Cr-4%Ni martensitic stainless steel ». Journal of Materials Processing Technology. vol. 209 , nº 4. p. 2195-2202.
L. Toubal, Philippe Bocher, A. Moreau. 2009. « Dwell-fatigue life of a near-alpha titanium alloy and ultrasonic measurement correlation ». 12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009) p. 1123-1128. International Congress on Fracture.
Lotfi Toubal, Philippe Bocher, André Moreau. 2009. « Dwell-fatigue life dispersion of a near alpha titanium alloy ». International Journal of Fatigue. vol. 31 , nº 3. p. 601-605.
E. Uta, N. Gey, Philippe Bocher, M. Humbert, J. Gilgert. 2009. « Texture heterogeneities in alpha(p)/alpha(s) titanium forging analysed by EBSD-Relation to fatigue crack propagation ». Journal of Microscopy. vol. 233 , nº 3. p. 451-459.
Henri Champliaud, Zhengkun Feng, Harald E. N. Bersee. 2009. « Three-point bending testing of sandwich beams and finite element comparison ». ASME International Mechanical Engineering Congress and Exposition (IMECE) (Lake Buena Vista, FL, USA, Nov. 13-19, 2009) p. 357-363. New York, NY, USA : American Society of Mechanical Engineers.
J-F. Charron, J. Teuwen, Simon Joncas, Harald E. N. Bersee, Henri Champliaud. 2009. « Vacuum infused anionic polyamide-6 composites : a comparison study between different mould heating strategies ». 24th Annual Technical Conference of the American Society for Composites and 1st Joint Canadian-American Technical Conference on Composites (Newark, DE, USA, Sept. 15-17, 2009) p. 931-946. DEStech Publications, Inc..
Zhengkun Feng, Henri Champliaud, Thien-My Dao. 2009. « Numerical study of non-kinematical conical bending with cylindrical rolls ». Simulation Modelling Practice and Theory. vol. 17 , nº 10. p. 1710-1722.
Zhengkun Feng, Henri Champliaud, Thien-My Dao. 2009. « Three-dimensional finite element analyses for pyramidal three-roll bending process ». ASME International Mechanical Engineering Congress and Exposition (IMECE) (Lake Buena Vista, FL, USA, Nov. 13-19, 2009) p. 9-14. New York, NY, USA : American Society of Mechanical Engineers.
Zhengkun Feng, Henri Champliaud, Van Ngan Lê, Thien-My Dao. 2009. « Analysis of roll bending processes based on finite element simulation ». Proceedings of the NAFEMS World Congress (Crete, Greece, June 16-19, 2009)
A. W. Hulskamp, Henri Champliaud, Harald E. N. Bersee. 2009. « Design and analysis of a scaled smart rotor blade for wind turbine load control ». ICCM-17 - 17th International Conference on Composite Materials (Edinburgh, UK, July 27-31, 2009) Vancouver, Canada : International Committee on Composite Materials.
Van Ngan Lê, Henri Champliaud, F. Martin, B Amri. 2009. « Rotating bending stresses in shrink-fit assemblies using FEM ». Proceedings of the NAFEMS World Congress (Crete, Greece, June 16-19, 2009)
François-Étienne Rhéaume, Henri Champliaud, Zhaoheng Liu. 2009. « Understanding and modelling the torsional stiffness of harmonic drives through finite-element method ». Proceedings of the Institution of Mechanical Engineers, Part C : Journal of Mechanical Engineering Science. vol. 223 , nº 2. p. 515-524.
R. Simoneau, D. Thibault, Jean-Luc Fihey. 2009. « A comparison of residual stress in hammer-peened, multi-pass steel welds-A514 (S690Q) and S41500 ». Welding in the World. vol. 53 , nº 5-6. p. R124-R134.
Sébastien Lalonde, Raynald Guilbault. 2009. « Finite separation method : an efficient boundary element crack modeling technique ». Computational Mechanics. vol. 44 , nº 6. 17 p. p. 791-807.
Sébastien Lalonde, Raynald Guilbault. 2009. « Numerical characterization of thin-rimmed gear tooth bending fatigue crack propagation ». 12th International Conference on Fracture 2009, ICF-12 (Ottawa, ON, Canada, July 12-17, 2009) p. 5827-5836. Japan : International Congress on Fracture.
D. Palaisi, Raynald Guilbault, Marc Thomas, A. A. Lakis, N. Mureithi. 2009. « Numerical simulations of damaged gear vibrations ». Proceedings of the 27th Seminar on Machinery Vibration (Vancouver, BC, Canada, Oct. 28-30, 2009)
F. Rafieian, Zhaoheng Liu, Bruce Hazel. 2009. « Dynamic model and modal testing for vibration analysis of robotic grinding process with a 6DOF flexible-joint manipulator ». International Conference on Mechatronics and Automation (ICMA) (Changchun, China, Aug. 9-12, 2009) p. 2793-2798. Piscataway, NJ, USA : Institute of Electrical and Electronics Engineers.
X. T. Pham, P. Gougeon, F. O. Gagnon. 2009. « Welding simulation of cast aluminium A356 ». Trends in Welding Research : proceedings of the 8th International Conference (Pine Mountain, GA, USA, June 01-06, 2008) p. 258-263. ASM International.
Houcine Ayari, Marc Thomas, Sylvie Doré, O. Serrus. 2009. « Evaluation of lumbar vertebra injury risk to the seated human body when exposed to vertical vibration ». Journal of Sound and Vibration. vol. 321 , nº 1-2. p. 454-470.
Houcine Ayari, Marc Thomas, Sylvie Doré, Rheda Taïar, Jean-Paul Dron. 2009. « Predicting the adverse health effects to long term whole-body vibration exposure ». Acoustique & Techniques . p. 44-52.
Houcine Ayari, Marc Thomas, Rheda Taïar, Jean-Paul Dron, Sylvie Doré. 2009. « Predicting the adverse health effects to long term whole-body vibration exposure ». 2nd International Conference on Industrial Risk Engineering = 2e Congrès International sur l’Ingénierie des Risques Industriels (CIRI) (Reims, France, 13-15 mai 2009)
Béchir Badri, Marc Thomas, Sadok Sassi, Imed Zaghbani, Victor Songmene, A. A. Lakis, N. Mureithi. 2009. « Instabilité des fraiseuses opérant à haute vitesse, provoquée par l’intéraction des défauts de roulements avec les résonances ». Proceedings of the 27th Seminar on Machinery Vibration (Vancouver, BC, Canada, Oct. 28-30, 2009) Canadian Machinery Vibration Association (CMVA) :
Béchir Badri, Marc Thomas, Sadok Sassi, Imed Zaghbani, Victor Songmene, A. A. Lakis, N. Mureithi. 2009. « Étude du comportement des roulements dans les rotors tournant à haute vitesse. ». 2nd International Conference on Industrial Risk Engineering = 2e Congrès International sur l'Ingénierie des Risques Industriels (CIRI) (Reims, France, 13-15 mai 2009)
M. Esmailzadeh, A. A. Lakis, Marc Thomas, L. Marcouiller. 2009. « Prediction of the response of a thin structure subjected to a turbulent boundary-layer-induced random pressure field ». Journal of Sound and Vibration. vol. 328 , nº 1-2. p. 109-128.
Y. Kerboua, A. A. Lakis, M. Thomas, L. Marcouiller, M. H. Toorani. 2009. « Critical velocity of potential flow in interaction with a system of plates ». 17th International Conference on Nuclear Engineering (ICONE 17) (Brussels, Belgium, July 12-16, 2009) p. 281-289. ASME.
Y. Kerboua, A. A. Lakis, M. Thomas, L. Marcouiller, M. H. Toorani. 2009. « Hybrid elements in fluid-structure interaction analysis of plates and shells ». Proceedings of the 12th International Conference on Civil, Structural and Environmental Engineering Computing (Funchal, Madeira, Portugal, Sept. 01-04, 2009) Civil-Comp Press.
Farid Mabrouki, Marc Thomas, M. Genest, A. Fahr. 2009. « Frictional heating model for efficient use of vibrothermography ». NDT & E International. vol. 42 , nº 5. p. 345-352.
Farid Mabrouki, Marc Thomas, Marc Genest, Abbas Fahr. 2009. « Numerical modeling of frictional heating based vibrothermography ». Health Monitoring of Structural and Biological Systems 2009 : The International Society for Optical Engineering (San Diego, CA, USA, Mar. 09-12, 2009) SPIE.
A. Ouahabi, Marc Thomas, A. A. Lakis. 2009. « Hybrid monitoring of crack location in riveted plates by combining an experimental modal analysis with numerical models ». 2nd International Conference on Industrial Risk Engineering = 2e Congrès International sur l'Ingénierie des Risques Industriels (CIRI) (Reims, France, 13-15 mai 2009)
K. A. Sghir, M. E. Badaoui, Marc Thomas, F. Guiller, M. Bakrim, D. Aboutajdine. 2009. « Parametric blind identification of the transfer function from vibration measurements based on second order cyclostationnarity ». 16th International Congress on Sound and Vibration 2009 (ICSV16) (Krakow, Poland, July 5-9, 2009) p. 4766-4773. International Institute of Acoustics & Vibration.
K. A. Sghir, M. El Badaoui, Marc Thomas, Imed Zaghbani, Victor Songmene, A. A. Lakis, N. Mureithi. 2009. « Identification aveugle paramétrique basée sur la cyclostationnarité à l’ordre deux de la fonction de transfert à partir des mesures vibratoires ». 2nd International Conference on Industrial Risk Engineering = 2e Congrès International sur l'Ingénierie des Risques Industriels (CIRI) (Reims, France, 13-15 mai 2009)
Yulan Sun, Marc Thomas, Jacques Masounave. 2009. « An experimental investigation of the dielectric properties of electrorheological fluids ». Smart Materials and Structures. vol. 18 , nº 2. 9 p.
Viet Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2009. « Online monitoring of varying modal parameters by operating modal analysis and model updating ». 2nd International Conference on Industrial Risk Engineering = 2e Congrès International sur l'Ingénierie des Risques Industriels (CIRI) (Reims, France, 13-15 mai 2009)
Viet Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2009. « Operational modal analysis of non-stationary mechanical systems by short-time autoregressive (STAR) modelling ». Proceedings IRF'2009 : 3rd International Conference on Integrity, Reliability and Failure (Porto, Portugal, July 20-24, 2009) Ediçoes INEGI.
Viet Hung Vu, Marc Thomas, A. A. Lakis, L. Marcouiller. 2009. « Software for operational modal analysis and automatic identification of modal parameters ». Proceedings of the 27th Seminar on Machinery Vibration (Vancouver, BC, Canada, Oct. 28-30, 2009) Canadian Machinery Vibration Association (CMVA).
Stéphane Hallé, Jules Kouam, Victor Songmene, François Morency, Martin Viens, Yves Cloutier, Jacques Masounave, Riad Khettabi, Abdelhakim Djebara. 2009. « Procédure de mesure et de contrôle des nanoparticules manufacturés ». Communication lors de la conférence : Conférences Scientifiques, Sécurité des Travailleurs et Contrôle des Risques Industriels ( Montréal, QC, Canada, 17 sept. 2009 )
R. Khettabi, A. Djebara, V. Songméné, M. Viens, S. Hallé, F. Morency, Y. Cloutier, J. Kouam, J. Masounave. 2009. « Procedure of measuring and controlling manufactured nanoparticles ». Communication lors de la conférence : INNO 2009 : La semaine de l'innovation ( Montréal, QC, Canada, 23-24 avr. 2009 )
Riad Khettabi, Abdelhakim Djebara, Victor Songmene, Martin Viens, Stéphane Hallé, François Morency, Yves Cloutier, Jules Kouam, Jacques Masounave. 2009. « Control and measuring of manufactured nanoparticle ». Affiche présentée lors de la conférence : INNO 09 : La Semaine de l'Innovation ( Montréal, Canada, 23-24 avril 2009 )
P. Belanger, P. Cawley. 2008. « LAMB wave tomography to evaluate the maximum depth of corrosion patches ». 34th Annual Review of Progress in Quantitative Nondestructive Evaluation (Golden, CO, USA, July 22-27, 2007) p. 1290-1297. AIP.
N. Boutana, P. Bocher, M. Jahazi, D. Piot, F. Montheillet. 2008. « Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ». Transactions of the Canadian Society for Mechanical Engineering. vol. 32 , nº 2. p. 195-213.
N. Boutana, Philippe Bocher, M. Jahazi, D. Piot, F. Montheillet. 2008. « The microstructural modeling of room temperature creep in titanium alloys using cellular automata model ». International Journal of Microstructure and Materials Properties. vol. 3 , nº 4-5. p. 642-653.
L. Germain, N. Gey, M. Humbert, P. Vo, M. Jahazi, Philippe Bocher. 2008. « Texture heterogeneities induced by subtransus processing of near alpha titanium alloys ». Acta Materialia. vol. 56 , nº 16. p. 4298-4308.
Lyes Hacini, Van Ngan Lê, Philippe Bocher. 2008. « Effect of impact energy on residual stresses induced by hammer peening of 304L plates ». Journal of Materials Processing Technology. vol. 208 , nº 1-3. p. 542-548.
H. Monajati, M. Jahazi, Philippe Bocher, S. Yue. 2008. « Dynamic recrystallization investigation during hot deformation of Udimet 720 nickel base superalloy ». Communication lors de la conférence : 14th International Metallurgy and Materials Congress ( Istanbul, Turkey, Oct. 16-18, 2008 )
A. Moreau, S.E. Kruger, M. Côté, Philippe Bocher. 2008. « In-Situ monitoring of microstructure during thermomechanical simulations using laser-ultrasonics ». Communication lors de la conférence : 1st Interntional Symposium on Laser Ultrasonics : Science, Technology and Applications ( Montreal, QC, Canada, July 16-18, 2008 )
André Moreau, Silvio E. Kruger, Marjolaine Côté, Philippe Bocher. 2008. « In-Situ monitoring of microstructure during thermomechanical simulations using laser-ultrasonics ». 1st Interntional Symposium on Laser Ultrasonics : Science, Technology and Applications (Montreal, QC, Canada, July 16-18, 2008)
E. Uta, Philippe Bocher, N. Gey, M. Humbert, J. Gilbert. 2008. « EBSD analysis of Dwell-fatigue fracture surface in titanium alloy IMI 834 ». Communication lors de la conférence : JIP, Fatigue and Plasticity : from Mechanisms to Design ( Paris, France, May 20-22, 2008 )
E. Uta, Philippe Bocher, N. Gey, M. Humbert, J. Gilgert. 2008. « EBSD analyses of dwell fracture surface in titanium alloy IMI-834 ». International Conference Fatigue and Plasticity From Mechanisms to Design (JIP) (Paris, France, May 20-22, 2008) p. 315-322.
Zhengkun Feng, Henri Champliaud, Thien-My Dao. 2008. « Modeling and simulation of conical bending with cylindrical rolls ». ASME Pressure Vessels and Piping Conference (PVP) (San Antonio, TX, USA, Jul. 22-26, 2007) p. 545-550. New York, NY, USA : American Society of Mechanical Engineers.
Zhengkun Feng, Henri Champliaud, Thien-My Dao. 2008. « Simulation analyses of a non-kinematical conical roll bending process with conical rolls ». 20th European Modeling and Simulation Symposium (EMSS) (Amantea, Italy, Sept. 17-19, 2008) p. 146-153. Italy : Diptim-Univ Genoa.
Zhengkun Feng, Henri Champliaud, Thien-My Dao. 2008. « Simulation of a three-stage process for forming a closed cone from a plate ». ASME Pressure Vessels and Piping Conference (PVP) (Chicago, IL, USA, Jul. 27-31, 2008) p. 947-953. New York, NY, USA : American Society of Mechanical Engineers.
Steeve Montminy, Erick Dupuis, Henri Champliaud. 2008. « Mechanical design of a hopper robot for planetary exploration using SMA as a unique source of power ». Acta Astronautica. vol. 62 , nº 6-7. p. 438-452.
H. N. Nguyen, Van Ngan Lê, Henri Champliaud, F. Martin. 2008. « Waving behaviour of fatigue stress fluctuation in shrink-fit assemblies using 3D finite elements ». 4th International Conference on High Performance Structures and Materials (HPSM) (Algarve, Portugal, May 13-15, 2008) p. 459-469. Southampton, UK : WITPress.
Jun Zeng, Zhaoheng Liu, Henri Champliaud. 2008. « FEM dynamic simulation and analysis of the roll-bending process for forming a conical tube ». Journal of Materials Processing Technology. vol. 198 , nº 1-3. p. 330-343.
R. Simoneau, D. Thibault, Jean-Luc Fihey. 2008. « A comparison of residual stress in hammer-peened, multi-pass steel welds - A514 (S690Q) and S41500 ». Communication lors de la conférence : 61st Annual Assembly of the International Welding Institute ( Graz, Austria, July 6-11, 2008 )
Raynald Guilbault, Marc Thomas. 2008. « Prediction of resonances of thin-rimmed cylindrical gears from a sub-structuring approach ». Canadian Society for Mechanical Engineering Forum (CSME) (Ottawa, ON, Canada, June 5-8, 2008) CSME.
Sébastien Lalonde, Raynald Guilbault. 2008. « A new and efficient approach for boundary element 2D crack modeling ». Canadian Society for Mechanical Engineering Forum (CSME) (Ottawa, ON, Canada, June 5-8, 2008)
Louis Lacasse, Antoine Tahan, Zhaoheng Liu. 2008. « Robust method for the automatic characterization of a wooden board's geometrical state ». Quality Engineering. vol. 20 , nº 2. p. 221-231.
Steven Roy, Zhaoheng Liu. 2008. « Road vehicle suspension and performance evaluation using a two-dimensional vehicle model ». International Journal of Vehicle Systems Modelling and Testing. vol. 3 , nº 1-2. p. 68-93.
H. Ayari, Marc Thomas, Sylvie Doré. 2008. « Development of an injury risk factor for drivers ». Revue Internationale sur l'lngénierie des Risques Industriels. vol. 1 , nº 2. p. 120-138.
A. Bouzidane, Marc Thomas. 2008. « An electrorheological hydrostatic journal bearing for controlling rotor vibration ». Computers and Structures. vol. 86 , nº 3-5. p. 463-472.
A. Bouzidane, Marc Thomas, A. A. Lakis. 2008. « Nonlinear dynamic behavior of a rigid rotor supported by hydrostatic squeeze film dampers ». Journal of Tribology. vol. 130 , nº 4. p. 041102-1.
M. Esmailzadeh, A. A. Lakis, Marc Thomas, L. Marcouiller. 2008. « Three-dimensional modeling of curved structures containing and/or submerged in fluid ». Finite Elements in Analysis and Design. vol. 44 , nº 6-7. p. 334-345.
Y. Kerboua, A. A. Lakis, Marc Thomas, L. Marcouiller. 2008. « Computational modeling of coupled fluid-structure systems with applications ». Structural Engineering and Mechanics. vol. 29 , nº 1. p. 91-111.
Y. Kerboua, A. A. Lakis, Marc Thomas, L. Marcouiller. 2008. « Vibration analysis of rectangular plates coupled with fluid ». Applied Mathematical Modelling. vol. 32 , nº 12. p. 2570-86.
S. Sassi, B. Badri, Marc Thomas. 2008. « Tracking surface degradation of ball bearings by means of new time domain scalar indicators ». International Journal of COMADEM. vol. 11 , nº 3. p. 36-45.
A. Szymanski, J. Masounave, M. Viens, J. Litwin. 2008. « Émission de poussière par frottement ». Colloque USIFORME 2007 (Montréal, QC, Canada, 3-5 mars 2008)
M. A. Arafin, M. Medraj, D. P. Turner, Philippe Bocher. 2007. « Effect of alloying elements on the isothermal solidification during TLP bonding of SS 410 and SS 321 using a BNi-2 interlayer ». Materials Chemistry and Physics. vol. 106 , nº 1. p. 109-119.
M. A. Arafin, M. Medraj, Daniel P. Turner, Philippe Bocher. 2007. « Transient liquid phase bonding of Inconel 718 and Inconel 625 with BNi-2: modeling and experimental investigations ». Materials Science and Engineering : A. vol. 447 , nº 1-2. p. 125-133.
N. Barka, A. Khelalfa, Philippe Bocher, J. Brousseau, S. Sundararajan. 2007. « Analysis of the effect of frequency using numerical modeling of induction hardening process ». Communication lors de la conférence : 1st International Conference of Sustainable Manufacturing ( Montreal, QC, Canada, Oct. 18-19, 2007 )
N. Boutana, Philippe Bocher, M. Jahazi, D. Piot, F. Montheillet. 2007. « Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ». Communication lors de la conférence : 11th World Conference on Titanium ( Kyoto, Japan, June 3-7, 2007 )
N. Boutana, Philippe Bocher, M. Jahazi, D. Piot, F. Montheillet. 2007. « Simulation of the mechanical behavior of hetegeogeneous materials using cellular automata ». Communication lors de la conférence : 1st International Conference of Sustainable Manufacturing ( Montreal, QC, Canada, Oct. 18-19, 2007 )
N. Boutana, Philippe Bocher, M. Jahazi, D. Piot, F. Motheillet. 2007. « Microstructural modeling of cold creep/fatigue in near alpha titanium alloys using cellular automata method ». Proceedings of TI-2007, 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007) p. 267-270. Warrendale, PA, USA : Minerals, Metals and Materials Society.
L. Germain, P. Vo, N. Gey, M. Jahazi, M. Humbert, Philippe Bocher. 2007. « Develpment of sharp local alpha microtectures during alpha/beta thermo-mechanical processing of Timetal 834 ». Communication lors de la conférence : 11th World Conference on Titanium ( Kyoto, Japan, June 3-7, 2007 )
Lionel Germain, Phuong Vo, Nathalie Gey, Mohammad Jahazi, Michel Humbert, Philippe Bocher. 2007. « Development of sharp local α microtextures during α/β thermo-mechanical processing of TIMETAL 834 ». 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007) p. 925-928. Warrendale, USA : Minerals, Metals and Materials Society.
L. Hacini, Van Ngan Lê, Philippe Bocher. 2007. « Traitement de surfaces par impacts : évaluation des contraintes résiduelles induites par martelage ». 18e Congrès Français de Mécanique (Grenoble, France, 27-31 août 2007) Courbevoie, France : AFM, Maison de la Mécanique.
K. Thibault-Liboiron, R. Alderliesten, R. Benedictus, Philippe Bocher. 2007. « Off-axis crack propagation and delamination growth in FML's ». Communication lors de la conférence : 6th Canadian International Conference on Composites (CANCOM) ( Winnipeg, MB, Canada, Aug. 14-17, 2007 )
E. Uta, M. Humbert, N. Gey, A. Hazotte, Philippe Bocher, M. Jahazi. 2007. « Description and characterisation of texture heterogeneities in titanium alloy Timetal 834 with a bimodal microstructure ». Communication lors de la conférence : World Titanium Conference ( Kyoto, Japan, June 3-7, 2007 )
E. Uta, M. Humbert, N. Gey, A. Hazotte, Philippe Bocher, M. Jahazi. 2007. « Description and characterisation of texture heterogeneitites in titanium alloy Timetal 834 with a bimodal microstructure ». 11th World Conference on Titanium (Kyoto, Japan, June 3-7, 2007) p. 259-262. Warrendale, USA : Minerals, Metals and Materials Society.
Phuong Vo, M. Jahazi, S. Yue, Philippe Bocher. 2007. « Flow stress prediction during hot working of near-alpha titanium alloys ». Materials Science and Engineering : A. vol. 447 , nº 1-2. p. 99-110.
Thibault Bellizi, Jonathan Boisvert, Henri Champliaud, Thien-My Dao. 2007. « Estimation of the pressing force in blade forming application ». Proceedings of the IASTED International Conference on Modelling and Simulation (Montreal, Canada, May 30-June 1, 2007) p. 272-277. Calgary, Canada : ACTA Press.
O Charette, Henri Champliaud, Marc Thomas. 2007. « FEM calculation of frequencies variation caused by residual stress distribution in welded structures ». Proceedings of the IASTED International Conference on Modelling and Simulation (Montreal, Canada, May 30-June 1, 2007) p. 446-451. Calgary, Canada : ACTA Press.
F. Duchaine, H.E.N. Bersee, Henri Champliaud. 2007. « The influence of the thickness on 3D elastic material properties of unidirectional e-glass/epoxy laminated composites ». 6th Canadian International Conference on Composites (CANCOM) (Winnipeg, MB, Canada, Aug. 14-17, 2007)
François Duchaine, Henri Champliaud. 2007. « Structured mesh generation by kriging with local refinement with a new elliptic scheme ». Engineering with Computers. vol. 23 , nº 1. p. 61-69.
Zhengkun Feng, Henri Champliaud, Thien-My Dao. 2007. « Modelling and simulation of conical bending process with sliding rolls ». IFAC Workshop on Manufacturing Modelling, Management and Control (Budapest, Hungary, Nov. 14-16, 2007)
Zhengkun Feng, Henri Champliaud, J. Zeng, Thien-My Dao. 2007. « Investigation of influence of sliding of rolls over plate on continuous bending with noncompatible conical rolls ». Proceedings of the IASTED International Conference on Modelling and Simulation (Montréal, Canada, May 30-June 1, 2007) p. 527-531. Calgary, Canada : ACTA Press.
Van Ngan Lê, Henri Champliaud, Brahim Amri. 2007. « A hysteresis approach of thermal expansion effect on residual stresses due to welding ». Proceedings of the IASTED International Conference on Modelling and Simulation (Montreal, Canada, May 30-June 1, 2007) p. 521-526. Calgary, Canada : ACTA Press.
Francis Martin, Van Ngan Lê, Henri Champliaud, Hoa Ngan Nguyen. 2007. « Stress concentration of shrink fit assembly using finite element method ». Proceedings of the IASTED Asian Conference on Modelling and Simulation (Beijing, China, Oct. 8-10, 2007) p. 67-70. Calgary, Canada : ACTA Press.
Hassan Nasri, Jacques Lanteigne, Henri Champliaud. 2007. « Usage of the contour method in measuring residual stress in welding and peen-welding applications ». Proceedings of the IASTED Asian Conference on Modelling and Simulation (Beijing, China, Oct. 8-10, 2007) p. 89-95. Calgary, Canada : ACTA Press.
H.N. Nguyen, Van Ngan Lê, Henri Champliaud, Francis Martin. 2007. « Stress concentration factor in shrink-fit shaft based on 3-D finite elements ». Proceedings of the 8th National Conference on Mechanics (Hanoi, Viêt Nam, Dec. 6-9, 2007)
Jian Hua Zhao, Henri Champliaud, Thien-My Dao. 2007. « Simulation of shear spinning process using finite element method ». Proceedings of the IASTED International Conference on Modelling and Simulation (Montreal, Canada, May 30-June 1, 2007) p. 239-245. Calgary, Canada : ACTA Press.
Jian-Hua Zhao, Henri Champliaud, Thien-My Dao. 2007. « Simulation of shear spinning process for pressure vessel components ». ASME Pressure Vessels and Piping Conference (PVP) (San Antonio, TX, USA, Jul. 22-26, 2007) p. 569-576. New York, NY, USA : American Society of Mechanical Engineers.
Zhaoheng Liu, Marc Thomas, Jean-Luc Fihey, Jinliang Li. 2007. « Dynamic analysis of manipulators with flexible joints and flexible links ». 5th International Conference on Industrial Automation = Cinquième Conférence Internationale sur l'Automatisation Industrielle (Montréal, Canada, June 11-13, 2007) Montréal, Qué., Canada : École de technologie supérieure.
G. Corriveau, Raynald Guilbault, Antoine Tahan. 2007. « Genetic algorithms and finite element coupling for mechanical optimization ». 10th International Conference on Optimum Design in Engineering (OPTI) (Myrtle Beach, USA, May 7- 9, 2007) p. 87-96. Southampton, UK : WITPress.
G. Corriveau, Raynald Guilbault, Antoine Tahan. 2007. « Optimisation d'une turbine hydroélectrique par algorithmes génétiques ». 5th International Conference on Industrial Automation = Cinquième Conférence Internationale sur l'Automatisation Industrielle (Montréal, Canada, June 11-13, 2007) Montréal, Qué., Canada : École de technologie supérieure.
B. Khalfi, Raynald Guilbault. 2007. « Turbine hydroélectrique Francis: un nouveau modèle rapide et précis de calcul des contraintes ». 5th International Conference on Industrial Automation = Cinquième Conférence Internationale sur l'Automatisation Industrielle (Montréal, Canada, June 11-13, 2007) Montréal, Qué., Canada : École de technologie supérieure.
L. Lacasse, Antoine Tahan, Zhaoheng Liu. 2007. « Automatic characterization of wood board surface defects ». 5th International Conference on Industrial Automation = Cinquième Conférence Internationale sur l'Automatisation Industrielle (Montreal, Canada, June 11-13, 2007) Montréal, Qué., Canada : École de technologie supérieure.
Zhaoheng Liu. 2007. « Characterisation of optimal human driver model and stability of a tractor-semitrailer vehicle system with time delay ». Mechanical Systems and Signal Processing. vol. 21 , nº 5. p. 2080-2098.
Zhaoheng Liu, Guy Payre. 2007. « Global bifurcation analysis of a nonlinear road vehicle system ». Journal of Computational and Nonlinear Dynamics. vol. 2 , nº 4. p. 308-315.
Zhaoheng Liu, Guy Payre. 2007. « Stability analysis of doubly regenerative cylindrical grinding process ». Journal of Sound and Vibration. vol. 301 , nº 3-5. p. 950-962.
Antoine Tahan, Zhaoheng Liu, L. Lacasse. 2007. « New method for characterization of wood ». 5th International Conference on Industrial Automation = Cinquième Conférence Internationale sur l'Automatisation Industrielle (Montreal, Canada, June 11-13, 2007) Montréal, Qué., Canada : École de technologie supérieure.
Jian-Hua Zhao, Zhaoheng Liu, My-Thien Dao. 2007. « Reliability optimization using multiobjective ant colony system approaches ». Reliability Engineering and System Safety. vol. 92 , nº 1. p. 109-120.
Marc Thomas, Frédéric Laville. Ordre des ingénieurs du Québec, Commission de la santé et de la sécurité du travail du Québec, Équipe de recherche en sécurité du travail, Réseau de recherche en santé et en sécurité du travail du Québec. 2007. « Premier congrès international sur l'ingénierie des risques industriels : CIRI 2007 : Montréal (Québec) Canada, 17-18 et 19 décembre 2007 : actes ». Montréal : École de technologie supérieure. 656 p.
H. Ayari, Marc Thomas, Sylvie Doré. 2007. « Development of an Injury Risk Factor for Drivers ». Premier congrès international sur l'ingénierie des risques industriels CIRI 2007 : Montréal, 17-19 décembre 2007 : actes : proceedings (Montreal, QC, Canada, Dec. 17-19, 2007) p. 137-150. Montréal : École de technologie supérieure.
H. Ayari, Marc Thomas, Sylvie Doré. 2007. « Un modèle statistique pour prédire l’influence de la posture, du poids, de l’ossature et de la densité osseuse sur la réponse dynamique d’un chauffeur exposé aux vibrations globales du corps ». Communication lors de la conférence : Séminaire Santé et Sécurité au Travail (SST) ( Montréal, QC, Canada, Jan. 2007 )
Houcine Ayari, Marc Thomas, Sylvie Doré. 2007. « A design of experiment for studying the effect of human body parameters on an injury risk of drivers exposed to vibration ». 37th International Conference on Computers and Industrial Engineering (CIE) (Alexandria, Egypt, Oct. 20-23, 2007) p. 2106-2114. Computers & Industrial Engineering.
B. Badri, Marc Thomas, R. Archambault, S. Sassi, A. Lakis. 2007. « A new method for shock detection and time-domain classification ». Congress theme: machinery & process health monitoring - future trends and prospects : proceedings of the 20th International Congress on Condition Monitoring and Diagnostic Engineering Management ; Faro, Portugal, June 13 - 15, 2007 ; COMADEM 2007 (Faro, Portugal, June 13-15, 2007) p. 667-676. Coimbra Inst. de Telecomunicações.
B. Badri, Marc Thomas, R. Archambault, S. Sassi, A. Lakis, N. Mureithi. 2007. « A new method to detect synchronous and asynchronous shock data in a signal ». Premier congrès international sur l'ingénierie des risques industriels CIRI 2007 : Montréal, 17-19 décembre 2007 : actes : proceedings (Montreal, QC, Canada, Dec. 17-19, 2007) p. 625-636. Montréal : École de technologie supérieure.
B. Badri, Marc Thomas, R. Archambault, S. Sassi, A. Lakis, N. Mureithi. 2007. « The shock extractor ». 25th Seminar on Machinery Vibration (Saint John, NL, Canada, Oct. 24-26, 2007) Calgary, Canada : CMVA.
B Badri, Marc Thomas, S. Sassi, A. Lakis. 2007. « Combination of bearing defect simulator and artifical neurl network of the diagnosis of damaged bearings ». Congress theme: machinery & process health monitoring - future trends and prospects : proceedings of the 20th International Congress on Condition Monitoring and Diagnostic Engineering Management ; Faro, Portugal, June 13 - 15, 2007 ; COMADEM 2007 (Faro, Portugal, June 13-15, 2007) p. 175-185. Coimbra Inst. de Telecomunicações.
Ahmed Bouzidane, Marc Thomas. 2007. « Equivalent stiffness and damping investigation of a hydrostatic journal bearing ». Tribology Transactions. vol. 50 , nº 2. p. 257-267.
Y. Kerboua, Aouni A. Lakis, Marc Thomas, L. Marcouiller. 2007. « Hybrid method for vibration analysis of rectangular plates ». Nuclear Engineering and Design. vol. 237 , nº 8. p. 791-801.
N.C. Komgon, N. Mureithi, A. Lakis, Marc Thomas. 2007. « On the use of time synchronous averaging, independent component analysis and support vector machines for bearing fault diagnosis ». Premier congrès international sur l'ingénierie des risques industriels CIRI 2007 : Montréal, 17-19 décembre 2007 : actes : proceedings (Montreal, QC, Canada, Dec. 17-19, 2007) p. 610-624. Montréal : École de technologie supérieure.
Sylvie Nadeau, Stéphane Hallé, S. Déry, P. Doucet, R. Gilbert, L. Gratton, Anh Dung Ngô, Jean Arteau, Hakim Bouzid, J. Brousseau, J. Dessureault, F. Gauthier, Frédéric Laville, P. Le-Huy, Françoise Marchand, Yvan Petit, D. Rodier, Marc Thomas. 2007. « Vers l'intégration de connaissances en santé et sécurité du travail en formation universitaire (génie mécanique) - une collaboration unique ». 24e Congrès de l’Association Internationale de Pédagogie Universitaire (AIPU) (Montréal, QC, Canada, 16-18 mai 2007) p. 96-100. Association Internationale de Pédagogie Universitaire (AIPU).
Anh Dung Ngô, Stéphane Hallé, Sylvie Nadeau, P. Déry, P. Doucet, R. Gilbert, L. Gratton, Jean Arteau, Hakim Bouzid, J. Brousseau, P. Dessureault, F. Gauthier, Frédéric Laville, P. Le Huy, Françoise Marchand, Yvan Petit, D. Rodier, Marc Thomas. 2007. « Le défi de l'intégration des connaissances en santé et en sécurité du travail - génie mécanique ». Travail et Santé. vol. 23 , nº 4. p. 36-39.
Abdelhakim Ouahabi, Marc Thomas, Makiko Kobayashi, Cheng Kuei Jen. 2007. « Structural health monitoring of aerospace structures with sol-gel spray sensors ». Damage Assessment of Structures VII (Turin, Italy, June 25-27, 2007) p. 505-510. Switzerland : Trans Tech Publications Ltd.
Mir Saeed Safizadeh, A. A. Lakis, Marc Thomas. 2007. « Machinery diagnosis by wavelet analysis ». Congress theme: machinery & process health monitoring - future trends and prospects : proceedings of the 20th International Congress on Condition Monitoring and Diagnostic Engineering Management ; Faro, Portugal, June 13 - 15, 2007 ; COMADEM 2007 (Faro, Portugal, June 13-15, 2006) p. 417-424. Coimbra Inst. de Telecomunicações.
Sadok Sassi, Bechir Badri, Marc Thomas. 2007. « A numerical model to predict damaged bearing vibrations ». Journal of Vibration and Control. vol. 13 , nº 11. p. 1603-1628.
Y. Sun, Marc Thomas, Jacques Masounave. 2007. « Experimental investigation of dielectric properties on electrorheological fluids ». International Conference on Smart Materials and Nanotechnology in Engineering (SMN) (Harbin, China, Jul. 1-4, 2007) Bellingham, WA, USA : SPIE - The International Society for Optical Engineering.
Marc Thomas, Frédéric Laville. 2007. « Simulation des vibrations mécaniques par Matlab, Simulink et Ansys ». Éd. rev. et corr. Québec : Presses de l'Université du Québec. 702 p.
V. H. Vu, M. Thomas, A. A. Lakis. 2007. « Le pont est-il fort? réponse d'une technique d'analyse modale opérationalle ». 42e congrès AQTR : défi : transport durable, 2 au 4 avril 2007 - Montréal : recueil des communications (Montreal, QC, Canada, Apr. 2-4, 2007) Montréal, Canada : AQTR.
V. H. Vu, M. Thomas, A. A. Lakis, L. Marcouiller. 2007. « Identification of added mass on submergeg vibrated plates ». 25th Seminar on Machinery Vibration (Saint John, NL, Canada, Oct. 24-26, 2007) p. 40.41-40.15. Calgary, AB, Canada : CMVA.
V. H. Vu, M. Thomas, A. A. Lakis, L. Marcouiller. 2007. « Identification of modal parameters by operational modal analysis of the assessment of bridge rehabilitation ». 2nd International Operational Modal Analysis Conference (IOMAC 2007) (Copenhaguen, Denmark, Apr. 30-May 2, 2007) p. 111-120. Aalborg · Denmark : Aalborg University.
V. H. Vu, M. Thomas, A. A. Lakis, L. Marcouiller. 2007. « Multi-regressive model for structural output only modal analysis ». 25th Seminar on Machinery Vibration (Saint John, NL, Canada, Oct. 24-26, 2007) p. 41.41-41.20. Calgary, Canada : CMVA.
V.H. Vu, Marc Thomas, A.A. Lakis, L. Marcouiller. 2007. « A time domain method for modal identification of vibratory signal ». Premier congrès international sur l'ingénierie des risques industriels CIRI 2007 : Montréal, 17-19 décembre 2007 : actes : proceedings (Montreal, QC, Canada, Dec. 17-19, 2007) p. 202-218. Montréal : École de technologie supérieure.
A. Szymanski, J. Masounave, M. Viens. 2007. « Les différentes sources d’émission de particules fines et ultrafines dans l’air ». Premier congrès international sur l'ingénierie des risques industriels : CIRI 2007 : Montréal (Québec) Canada, 17-18 et 19 décembre 2007 : actes (Montréal, QC, Canada, 17-19 déc. 2007) Montréal : École de technologie supérieure.
P. Bélanger, A. Berry, Y. Pasco, Y. St-Amant, S. Rajan. 2006. « Active structural acoustic control of a Bell 407 transmission noise ». AHS (American Helicopter Society) 62nd Annual Forum (Phoenix, AZ, USA, May 09-11, 2006) p. 788-797. AHS.
M. A. Arafin, M. Medraj, D. P. Turner, P. Bocher. 2006. « Optimization of process variables during TLP Bonding of nickel superalloys ». Aerospace materials and manufacturing : emerging materials, processes, and repair techniques : proceedings of the third International [Symposium] on Aerospace Materials and Manufacturing : emerging materials, processes and repair techniques, October 1-4, (Montreal, QC, Canada, Oct. 1-4, 2006) p. 301-314. Canadian Institute of Mining, Metallurgy and Petroleum.
M. A. Arafin, M. Medraj, D. P. Turner, Philippe Bocher. 2006. « Thermodynamic modeling and experimental investigation of brazed joints used in aerospace industry ». 3rd International Brazing and Soldering Conference (San Antonio, TX, USA, April 24-26, 2006) p. 189-196. Materials Park, OH, USA : ASM International.
Muhammad A. Arafin, Mamoun Medraj, Daniel P. Turner, Philippe Bocher. 2006. « Mathematical Modeling and Experimental Investigations of Isothermal Solidification during Transient Liquid Phase Bonding of Nickel Superalloys ». THERMEC 2006 Supplement (Vancouver, Canada, Jul. 4 - 8, 2006) p. 882-887. Clausthal-Zellerfeld, Germany : Trans Tech Publications.
N. Barka, Philippe Bocher, J. Brousseau, Michel Galopin, S. Sundararajan. 2006. « Modeling and sensitivity study of the induction hardening process ». THERMEC 2006 Supplement (Vancouver, Canada, Jul. 4-8, 2006) p. 525-530. Uetikon-Zuerich, Switzerland : Trans Tech Publications.
N. Barka, Philippe Bocher, Michel Galopin, J. Brousseau, S. Sundararajan. 2006. « Sensitivity study of induction hardening machine parameters of SAE-4340 steel specimen ». Conference of Metallurgists (COM) (Montreal, QC, Canada, Oct. 1-4, 2006) p. 525-530. Montreal, Canada : The Metallurgy and Materials Society of CIM.
Nabil Boutana, Philippe Bocher, Mohammad Jahazi, D. Piot, F. Montheillet. 2006. « Utilisation des automates cellulaires pour étudier le comportement en fatigue-fluage des alliages de titane ». Matériaux 2006 (Dijon, France, 13-17 nov. 2006) p. 781-790.
L. Dubourg, M. Jahazi, G. Dezaise, P. Bocher. 2006. « Microstructure and mechanical characterisation of FSW 7075-T6 lap joints ». Aerospace Materials and Manufacturing: Emerging Materials, Processes, and Repair Techniques (Montréal, Canada, Oct.1-4, 2006) p. 107-120. Canadian Institute of Mining, Metallurgy and Petroleum.
L. Hacini, Van Ngan Lê, Philippe Bocher, D. Thibault. 2006. « Effect of energy level on stresses induced by robotized hammer peening ». Conference of Metallurgists (COM) (Montreal, QC, Canada, Oct.1-4, 2006) p. 781-790 . Montreal, Canada : The Metallurgy and Materials Society of CIM.
L. Hacini, Van Ngan Lê, Philippe Bocher, D. Thibault. 2006. « Residual stresses induced by robotized hammer peening : the effect of impact energy level ». Aerospace materials and manufacturing : emerging materials, processes, and repair techniques : proceedings of the third International [Symposium] on Aerospace Materials and Manufacturing : emerging materials, processes and repair techniques, October 1-4, (Montreal, QC, Canada, Oct. 2-4, 2006) p. 759-768. Montreal : Canadian Institute of Mining, Metallurgy and Petroleum.
Michel Humbert, L. Germain, N. Gey, Philippe Bocher, M. Jahazi. 2006. « Study of the variant selection in sharp textured regions of bimodal IMI 834 billet ». Materials Science and Engineering : A. vol. 430 , nº 1-2. p. 157-164.
E. Uta, M. Humbert, N. Gey, P. Bocher, M. Jahazi. 2006. « Mise en évidence et caractérisation des hétérogénéités de textures dans l'alliage de titane IMI 834 de microstructure bimodale à vocation aéronautique ». Materiaux 2006 : Dijon, 13-17 Novembre 2006 : [recueil de la conference sur CD-ROM] (Dijon, France, 13-17 nov. 2006) Dijon : Université de Bourgogne.
Jonathan Boisvert, Thibaut Bellizzi, Henri Champliaud, Patrice Seers. 2006. « Print depth prediction in hot forming process with a reconfigurable die ». ANSYS Conference and Exhibition (Pittsburgh, PA, USA, May 2-4, 2006)
Jonathan Boisvert, Henri Champliaud, Thibaut Bellizzi, Patrice Seers. 2006. « Simulation and optimisation of a reconfigurable discrete die for the hot forming of thick steel plates in hydro power industry ». ANSYS Conference and Exhibition (Pittsburgh, PA, USA, May 2-4, 2006)
François Duchaine, E.M. Baten, Henri Champliaud, H.E.N. Bersee. 2006. « Comparison of beam theories with finite elemente analysis in three-point bending of thick composites ». 8th International Conference on Computational Structures Technology (Las Palmas de Gran Canaria, Spain, Sept.12-15, 2006) Stirlingshire, UK : Civil-Comp Press.
Steeve Montminy, Erick Dupuis, Henri Champliaud. 2006. « Mechanical design of a hopper robot for planetary exploration using SMA as a unique source of power ». AIAA 57th International Astronautical Congress (IAC) (Valencia, Spain, Oct. 2-6, 2006) p. 5288-5297. Reston, VA, USA : American Institute of Aeronautics and Astronautics Inc..
F.-É Rhéaume, Henri Champliaud, Zhaoheng Liu. 2006. « Simulating strain wave gearing torsional stiffness using the finite element method ». ANSYS Conference and Exhibition (Pittsburgh, PA, USA, May 2-4, 2006)
Raynald Guilbault. 2006. « Tooth influence on flexural and torsional flexibility, and model tooth number prediction for optimum dynamic simulation of wide-faced spur gears ». Journal of Mechanical Design. vol. 128 , nº 3. p. 626-633.
Raynald Guilbault, Claude Gosselin, Louis Cloutier. 2006. « Helical gears, effects of tooth deviations and tooth modifications on load sharing and fillet stresses ». Journal of Mechanical Design. vol. 128 , nº 2. p. 444-456.
Sébastien Lalonde, Raynald Guilbault. 2006. « Dynamic analysis of spur gears by non linear modeling ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 15-35. Calgary : ACVM.
R. Wuthrich, L. A. Hof. 2006. « The gas film in spark assisted chemical engraving (SACE) - A key element for micro-machining applications ». International Journal of Machine Tools and Manufacture. vol. 46 , nº 7-8. p. 828-835.
Marc Thomas, Zhaoheng Liu, Érik Bouthillier. 2006. « Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 ». Calgary, Canada : ACVM.
Benoît Lacroix, Patrice Seers, Zhaoheng Liu. 2006. « A passive nonlinear damping design for a road race car application ». Non-Conference Specific Technical Papers - 2006 (Warrendale, PA, USA, Dec., 2006) Warrendale, PA : SAE International.
Benoît Lacroix, Patrice Seers, Zhaoheng Liu. 2006. « Race car suspension design with a nonlinear damping ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 54-65. Calgary, Canada : CMVA.
Zhaoheng Liu, G. Payre. 2006. « Chatter onset prediction of doubly regenerative cylindrical grinding process ». Proceedings of the Second International Conference on Dynamics, Vibration and Control (Beijing, China, Aug. 23-26, 2006)
Steven Roy, Zhaoheng Liu. 2006. « Modeling and simulation of a parametric vehicle for suspension and performance analysis ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 23-26, 2006) p. 66-82. Calgary, Canada : ACVM.
Bechir Badri, Marc Thomas, R. Archambault, Sadok Sassi. 2006. « La transformée de Julien pour différentier les chocs synchrones des chocs asynchrones ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 448-459 . Calgary, Canada : ACVM.
Bechir Badri, Marc Thomas, Sadok Sassi. 2006. « Étude et développement d'un système expert basé sur les réseaux de neurones pour le diagnostic des défauts de roulements ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montréal, QC, Canada, 25-27 oct. 2006) p. 386-403. Calgary, Canada : ACVM.
M. Esmailzadeh, A.A. Lakis, Marc Thomas, L. Marcouiller. 2006. « Three dimentionnal modeling of curved structure partially or completely containing and or submerged in fluid ». Montréal. École Polytechniquel de Montréal. 37 p.
Martin Gagnon, Antoine Tahan, André Coutu, Marc Thomas. 2006. « Analyse modale opérationnelle en présence d'excitations harmoniques : étude de cas sur des composantes de turbine hydroélectrique ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montréal, QC, Canada, 25-27 oct. 2006) p. 320-329. Calgary, Canada : ACVM.
Y. Kerboua, A. A. Lakis, Marc Thomas, L. Marcouiller, M. H. Toorani. 2006. « Dynamic analysis of coupled-fluid structure systems ». WSEAS Transactions on Applied and Theoretical Mechanics. vol. 1 , nº 2. p. 265-274.
Y. Kerboua, A.A. Lakis, Marc Thomas, L. Marcouiller, M.H. Toorani. 2006. « Dynamic analysis of coupled-fluid structure systems ». Proceedings of the 2nd WSEAS International Conference on Applied and Theoretical Mechanics (Venice, Italy, Nov. 20-22, 2006) p. 249-258.
Asma Kotrane, Marc Thomas, Sadok Sassi. 2006. « Conception, réalisation et caracterisation dynamique d’un amortisseur magnéto-rhéologique ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 473-491. Calgary, Canada : ACVM.
A. Ouahabi, Marc Thomas, A.A. Lakis. 2006. « Detection of damages in beams and composite plates by harmonic excitation and time-frequency analysis ». dings of the 3rd European Workshop - Structural Health Monitoring 2006 (Granada, Spain, July 5-7, 2006) p. 775-782. Lancaster, PA, USA : Destech publications inc.
A. Ouahabi, Marc Thomas, A.A. Lakis. 2006. « Détection de fissures de respiration de fatigue par excitation harmonique et analyse temps-fréquence ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montréal, QC, Canada, 25-27 oct. 2006) p. 460-472. Calgary, Canada : ACVM.
A. Ouahabi, Marc Thomas, F. Léonard. 2006. « Detection of damages in beams and composite plates by harmionic excitation and time-frequency analysis ». Communication lors de la conférence : 24nd Seminar on Canadian Machinery Vibration Association (CMVA) = 24e Séminaire en Vibration de Machines (ACVM) ( Montreal, QC, Canada, Oct. 25-27, 2006 )
Sadok Sassi, Bechir Badri, Marc Thomas. 2006. « "TALAF" and "THIKAT" as innovative time domain indicators for tracking BALL bearings ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 404-419. Calgary, Canada : ACVM.
Yulan Sun, Marc Thomas, Jacques Masounave. 2006. « Amortissement des vibrations de torsion de rotors à l’aide de fluides électro-rhéologiques ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 344-369. Calgary, Canada : ACVM.
Marc Thomas. 2006. « Effet des contraintes résiduelles de soudage sur les résonances des structures ». Communication lors de la conférence : 24nd Seminar on Canadian Machinery Vibration Association (CMVA) = 24e Séminaire en Vibration de Machines (ACVM) ( Montréal, QC, Canada, 25-27 oct. 2006 )
Marc Thomas, Frédéric Laville, François Lafleur. 2006-01-17. « Modal analysis method and apparatus therefor ».
Viet Hung Vu, Marc Thomas, A.A. Lakis. 2006. « Analyse modale en opération par méthodes temporelles ». Compte rendu 24ième séminaire sur la vibration des machines : ACVM, 25-27 octobre 2006 (Montreal, QC, Canada, Oct. 25-27, 2006) p. 330-343. Calgary, Canada : CMVA.
P. Bocher, M. Jahazi, L. Germain, N. Gey, M. Humbert. 2005. « Variant selection in forged titanium alloys : effect of microscopic grain misorientations on the formation of macroscopic regions with similar crystallographic orientations ». Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, QC, Canada, Aug. 1-4, 2005) p. 523-530. Montréal, Qué., Canada : École de technologie supérieure.
Philippe Bocher, Mohammad Jahazi, Lionel Germain, Priti Wanjara, Nathalie Gey, Michel Humbert. 2005. « β Microtexture analysis in correlation with hcp textured regions observed in a forged near alpha titanium alloy ». Solid State Phenomena. vol. 105 p. 127-132.
N. Boutana, P. Bocher, M. Jahazi, J. Savoie, D. Piot, F. Montheillet. 2005. « Modelling mechanical behaviour of heterogeneous materials using cellular automata : application to some forged titanium alloys ». Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, QC, Canada, Aug. 1-4, 2005) p. 273-280. Montréal, Qué., Canada : École de technologie supérieure.
L. Germain, N. Gey, M. Humbert, P. Bocher, M. Jahazi. 2005. « β→-αs variant selection in sharp hcp textured regions of a bimodal IMI834 billet ». Materials Science Forum. Proceedings of the 14th International Conference on Textures of Materials (Leuven, Belgium, July 11-15, 2005) p. 663-668. Trans Tech Publications.
L. Germain, N. Gey, M. Humbert, A. Hazotte, P. Bocher, M. Jahazi. 2005. « An automated method to analyze separately the microtextures of primary αp grains and the secondary αs inherited colonies in bimodal titanium alloys ». Materials Characterization. vol. 54 , nº 3. p. 216-222.
Lionel Germain, Nathalie Gey, Ludovic Humbert, Philippe Bocher, Mohammad Jahazi. 2005. « Analysis of sharp microtexture heterogeneities in a bimodal IMI 834 billet ». Acta Materialia. vol. 53 , nº 13. p. 3535-3543.
Ali Reza Khodabandeh, Mohammad Jahazi, Steve Yue, Philippe Bocher. 2005. « Impact toughness and tensile properties improvement through microstructure control in hot forged Nb-V microalloyed steel ». ISIJ International. vol. 45 , nº 2. p. 272-280.
P. Wanjara, H. Monajati, M. Jahazi, L. Germain, P. Bocher, J.-P. Immarigeon. 2005. « Deformation processing mechanism and microstructural evolution in a near-alpha titanium alloy ». Materials science & technology: proceedings of the conference held September 25-28, 2005, Pittsburgh, Pennsylvania USA (Pittsburgh, PA, USA, Sept. 25-28, 2005) p. 15-26. Association for Iron and Steel Technology.
Henri Champliaud, Abdel-Hakim Bouzid. 2005. « Computation of unloading stiffness of nonlinear gaskets using dual kriging interpolation ». Materials for safety and health : mesoscopic and multiscale consideration in modern science and engineering (Montreal, Canada, Aug. 1-4, 2005) p. 127-138. Montréal, Qué., Canada : École de technologie supérieure.
Henri Champliaud, Abdelmajid Lajmi, Ngan Van Lê. 2005. « Finite element analysis of a three-point belt tension tester ». Non-Conference Specific Technical Papers (Troy, MI, USA, Sept. 1, 2005) SAE.
Marie-Josée Potvin, Bruno Sylvestre, Henri Champliaud. 2005. « Development of a small deployable membrane antenna ». Canadian Aeronautics and Space Institute Conference (Toronto, ON, Canada, Apr. 26-27, 2005)
P. Terrier, P. Seers, H. Champliaud. 2005. « Comparison of emissions and fuel consumption between gasoline and E85 in a simulated hybrid electric vehicle ». Powertrain & Fluid Systems Conference and Exhibition (San Antonio, TX, USA, Oct. 24-27, 2005) SAE International.
Marc Thomas, Henri Champliaud. 2005. « Effect of residual stresses on modal parameters of welded structures ». 23rd Seminar on Machinery Vibration (Edmonton, AB, Canada, Oct. 26-28, 2005) Calgary, Canada : CMVA.
Raynald Guilbault. 2005. « Modes vibratoires des roues d'engrenage cylindriques : un outil de conception adapté ». Communication lors de la conférence : Conférence de l'Association Canadienne en Vibration des Machines (ACVM) ( Montréal, QC, Canada, Oct. 2005 )
Raynald Guilbault, L. Cloutier. 2005. « Numerical investigation of the influence of rim and web thickness on vibration modes of thin-rimmed cylindrical gears ». Communication lors de la conférence : International Conference on Gears ( Munich, Germany, Sept. 14-16, 2005 )
Raynald Guilbault, L. Cloutier. 2005. « Numerical investigation of the influence of rim and web thickness on vibration modes of thin-rimmed cylindrical gears ». International Conference on Gears (Munich, Germany, Sept. 14-16, 2005) p. 651-669. Germany : VDI Verlag GMBH.
Raynald Guilbault, Claude Gosselin, Louis Cloutier. 2005. « Express model for load sharing and stress analysis in helical gear ». Journal of Mechanical Design. vol. 127 , nº 6. p. 1161-1172.
R. Wuthrich, K. Fujisaki, P. Couthy, L. A. Hof, H. Bleuler. 2005. « Spark assisted chemical engraving (SACE) in microfactory ». Journal of Micromechanics and Microengineering. vol. 15 , nº 10. p. 276-280.
R. Wuthrich, L. A. Hof, A. Lal, K. Fujisaki, H. Bleuler, P. Mandin, G. Picard. 2005. « Physical principles and miniaturization of Spark Assisted Chemical Engraving (SACE) ». Journal of Micromechanics and Microengineering. vol. 15 , nº 10. p. 268-275.
K. Melhem, Zhaoheng Liu. 2005. « A unified modeling and stabilization framework for interconnected rigid bodies ». In Intelligent systems at the service of mankind 2. p. 141-160. Ubooks.
Khoder Melhem, Zhaoheng Liu, Antonio Loria. 2005. « A unified framework for dynamics and lyapunov stability of holonomically constrained rigid bodies ». Journal of Advanced Computational Intelligence and Intelligent Informatics. vol. 9 , nº 4. p. 387-394.
Jian Hua Zhao, Zhaoheng Liu, My-Thien Dao. 2005. « Solving reliability optimal design problem using ant colony system (ACS) approaches ». Proceedings of the 15th International CIRP Design Seminar (Shanghai, China, May 22-25, 2005) p. 32-40.
Jian-Hua Zhao, Thien-My Dao, Zhaoheng Liu. 2005. « Optimization of mechanical systems reliability using ant colony based simulation approach ». Proceedings of the IASTED International Conference on Modelling and Simulation (Cancun, Mexico, May 18-20, 2005) p. 182-187. Calgary, Canada : ACTA Press.
Xuan-Tan Pham, Phil Bates, Amy Chesney. 2005. « Modeling of thermoforming of low-density glass mat thermoplastic ». Journal of Reinforced Plastics and Composites. vol. 24 , nº 3. p. 287-298.
H. Ayari, Marc Thomas, Sylvie Doré. 2005. « Développement d'un modèle statistique de prédiction de la durée de vie du rachis lombaire, dépendant de la contrainte appliquée, de l'âge et de la densité osseuse ». Perspectives Interdisciplinaires sur le Travail et la Santé . vol. 7 , nº 2. p. 14.
H. Ayari, Marc Thomas, Sylvie Doré. 2005. « Évaluation par un modèle d'éléments finis paramétrique des contraintes dynamiques dans le rachis lombaire, dues aux vibrations du corps entier ». Communication lors de la conférence : Séminaire Santé et Sécurité au Travail (SST) ( Montréal, QC, Canada, Nov. 2005 )
Béchir Badri, Marc Thomas, René Archambault, Sadok Sassi. 2005. « La transformée de Julien : une nouvelle procédure de traitement de signal pour la détection des chocs ». 23rd Seminar on Machinery Vibration (Edmonton, AB, Canada, Oct. 26-28, 2005) Calgary, Canada : ACVM.
A. Bouzidane, Marc Thomas. 2005. « An electrorheological hydrostatic journal bearing for controlling rotor vibration ». II Eccomas Thematic Conference on Smart Structures and Materials, Lisbon, 18-21 July 2005 : proceedings and papers (Lisbon, Portugal, July 18-21, 2005)
M. Guerra, Marc Thomas, Éric David. 2005. « Turbomachinery blade vibratory stress prediction using contact elements modeling ». Symposium on the Evaluation, Control, and Prevention of High Cycle Fatigue in Gas Turbine Engines for Land, Sea and Air Vehicles (Seville, Spain, Oct. 3-7, 2005)
Y. Kerboua, A.A. Lakis, Marc Thomas, L. Marcouiller. 2005. « Comportement dynamique des plaques rectangulaires submergées ». Montréal. École polytechnique de Montréal. 78 p.
S. Sassi, K. Cherif, L. Mezghani, Marc Thomas, A Kotrane. 2005. « An innovative magnetorheological damper for automotive suspension: from design to experimental characterization ». Smart Materials and Structures. vol. 14 , nº 4. p. 811-822.
Marc Thomas, K. Abassi, A. A. Lakis, J. L. Marcouiller. 2005. « Analyse modale expérimentale d'une structure soumise à un écoulement turbulent ». 23rd Seminar on Machinery Vibration (Edmonton, AB, Canada, Oct. 26-28, 2005) Calgary, Canada : CMVA.
Marc Thomas, Frédéric Laville. 2005. « Simulation des vibrations mécaniques par Matlab, Simulink et Ansys ». Québec : Presses de l'Université du Québec. 702 p.
Martin Viens, Z. Wang. 2005. « HBAR-spectroscopy used for materials characterization ». 32nd Annual Review of Process in Quantitative Nondestructive Evaluation (Brunswick, ME, USA, Jul. 31-Aug. 5, 2005) Melville, NY, USA : American Institute of Physics.
Philippe Bocher, M. Jahazi, P. Wanjara, L. Germain, N. Gey, M. Humbert. 2004. « Microtexture analysis in correlation with hcp textured regions observed in a forged near alpha titanium alloy ». Communication lors de la conférence : 2nd International Conference on Texture and Anisotropy of Polycrystals (ITAP-2) ( Metz, France, July 7-9, 2004 )
Mohammad Jahazi, Lionel Germain, Nathalie Gey, Michel Humbert, Philippe Bocher. 2004. « Specific EBSD data processing to analyse separately the ap/as microtexture of bimodal Titanium alloys ». Materials Characterization. vol. 54 p. 216-222.
Abdel-Hakim Bouzid, Henri Champliaud. 2004. « Contact stress evaluation of nonlinear gaskets using dual kriging interpolation ». Journal of Pressure Vessel Technology. vol. 126 , nº 4. p. 445-450.
Van Ngan Lê, Anh Dung Ngô, Françoise Marchand, Henri Champliaud, F. Packwood. 2004. « Calculating tension force in belts retaining steel rolls by finite elements ». 7th National Conference on Mechanics of Deformable Bodies (Do-Son, Vietnam, Aug. 27-28, 2004)
K. Fujisaki, Ph. Couthy, R. Wüthrich, L. A. Hof, H. Bleuler. 2004. « Spark Assisted Chemical Engraving (SACE) in microfactory ». Affiche présentée lors de la conférence : Fourth International Workshop on Microfactories ( Shanghai, China, Oct. 15-17, 2004 )
L. A. Hof, A. Lal, K. Fujisaki, R. Wüthrich, H. Langen, H. Bleuler. 2004. « 3D Micro structuring of glass with an AFM ». Proceedints of the EUSPEN International Conference, 2004 (Glasgow, Scotland, UK, May 31 - June 02, 2004) p. 89-90. Kempston : LG Digital.
L. A. Hof, Rolf Wüthrich, Hannes Bleuler, Ph. Mandin. 2004. « Physical principles and miniaturization of Spark Assisted Chemical Engraving (SACE) ». Affiche présentée lors de la conférence : Fourth International Workshop on Microfactories ( Shanghai, China, Oct. 15-17, 2004 )
Zhaoheng Liu, Guy Payre, Paul Bourassa. 2004. « Stability and oscillations in a time-delayed vehicle system with driver control ». Nonlinear Dynamics. vol. 35 , nº 2. p. 159-173.
Khoder Melhem, Zhaoheng Liu, Antonio Loria. 2004. « A unified framework for dynamics and Lyapunov stability of holonomically constrained rigid bodies ». 2nd IEEE International Conference on Computational Cybernetics (Vienna, Austria, Aug. 30-Sept. 1, 2004) p. 199-205. Piscataway, NJ, USA : Institute of Electrical and Electronics Engineers.
H. Ayari, Marc Thomas, Sylvie Doré. 2004. « Développement d'un modèle statistique de prédiction de la durée de vie du rachis lombaire dépendant de la contrainte appliquée, de l'âge et de la densité osseuse ». Communication lors de la conférence : 72e Congrès de l'ACFAS ( Montréal, QC, Canada, 10-14 mai 2004 )
B. Badri, Marc Thomas, S. Sassi. 2004. « Caractérisation numérique et expérimentale du comportement vibratoire de roulements endommagés ». Communication lors de la conférence : Conférence de l' Association Canadienne en Vibrations de Machines (ACVM) ( Montréal, QC, Canada, janv. 2004 )
Mario Guerra, Marc Thomas, Lyne St-George. 2004. « Turbomachinery blade modal analysis using contact elements ». World Aviation Congress & Exposition (Reno, NV, USA, Nov. 2-4, 2004) SAE International.
François Lafleur, Frédéric Laville, Marc Thomas. 2004-07-13. « Modal analysis method and apparatus therefor ».
François Lafleur, Marc Thomas, Frédéric Laville. 2004-11-02. « Method for determining a vibratory excitation spectrum tailored to physical characteristics of a structure ».
Y. Sun, Marc Thomas, Jacques Masounave. 2004. « Investigation of dynamic behaviour of electrorheological fluids by experimental design ». Proceedings : 7th CanSmart Meeting : International Workshop Smart Materials & Structures (Montreal, QC, Canada, Oct. 21-22, 2004) p. 153-162. Kingston, Ontario : CanSmart Group.
Marc Thomas, Aouni A. Lakis, Sadok Sassi. 2004. « A theoretical model for predicting adverse health effects of long-term whole-body random vibration exposure ». Recent Research Developments in Sound and Vibration. vol. 2 p. 55-73.
L. Germain, N. Gey, M. Humbert, P. Bocher, M. Jahazi. 2003. « Texture and microtexture analysis of an IMI 834 alloy after thermo-mechanical processing ». Ti-2003 Science and Technology : proceedings of the 10th World Conference on Titanium held at the CCH-Congress Center Hamburg, Germany, 13-18 July 2003 (Hamburg, Germany, July 13-18, 2003) p. 1283-1290. Weinheim, Allemagne : Wiley-VCH.
Hakim A. Bouzid, Henri Champliaud. 2003. « On the use of dual kriging interpolation for the evaluation of the gasket stress distribution in bolted joints ». Pressure Vessels and Piping Conference (PVP) (Cleveland, OH, USA, Jul. 20-24, 2003) p. 77-83. USA : American Society of Mechanical Engineers.
Henri Champliaud, François Duchaine, Van Ngan Lê. 2003. « Controlling normal direction and thickness of interpolated surfaces of complex thin parts ». 4th International Conference on Industrial Automation (Montreal, QC, Canada, June 9-11, 2003)
Henri Champliaud, Abdelmajid Lajmi, Van Ngan Lê. 2003. « Numerical approach of twist-off torque prediction for cap bottle closure ». 4th International Conference on Industrial Automation (Montreal, QC, Canada, June 9-11, 2003)
Henri Champliaud, N. V. Le. 2003. « Prediction of the leakage pressure of a cap and bottle assembly using the finite element method ». Glass Technology. vol. 44 , nº 6. p. 225-230.
F. Duchaine, Henri Champliaud, O. Morin, Van Ngan Lê. 2003. « Maillage par krigeage de volume par reconnaissance des contours des sections dans un environnement CAD ». Communication lors de la conférence : 71e Congrès de l'ACFAS ( Rimouski, QC, Canada, 19-23 mai 2003 )
A. Lajmi, Henri Champliaud, Van Ngan Lê. 2003. « Effet du fluage sur le comportement du joint d'étanchéité dans les fermetures filetées ». Communication lors de la conférence : 71e Congrès de l'ACFAS ( Rimouski, QC, Canada, 19-23 mai 2003 )
O. Morin, Henri Champliaud, F. Duchaine, Hakim Bouzid. 2003. « Krigeage du comportement des joints d'étanchéité au chargement et au déchargement ». Communication lors de la conférence : 71e Congrès de l'ACFAS ( Rimouski, QC, Canada, 19-23 mai 2003 )
Raynald Guilbault. 2003. « Mise au point d'un laboratoire sur l'équilibrage dynamique des rotors rigides déséquilibrés pour le cours MEC729 - Mécanismes et dynamique des machines ». Journée d'Échanges sur les Réalisations Pédagogiques : PSIRE - Enseignement 2002-2003 : Actes (Montréal, QC, Canada, 25 avril 2003) p. 49-57. École de technologie supérieure.
Marek Teichmann, Zhaoheng Liu. 2003. « Non convex mesh penetration distance for rigid body dynamics ». ACM SIGGRAPH 2003 Conference on Sketches & Applications (San Diego, CA, USA, July 27-31, 2003) USA : ACM.
François Lafleur, Marc Thomas, Frédéric Laville. 2003. « Environmental stress screening (ESS) par excitation acoustique ». Proceedings of the 21st Machinery Vibration Seminar = Compte rendu du 21e Séminaire sur les Vibrations des Machines (Halifax, NS, Canada, Oct. 29-31, 2003) Canada : Canadian Machinery Vibration Association.
Sadok Sassi, Khaled Cherif, Marc Thomas. 2003. « On the design and testing of a smart car damper based on electro-rheological technology ». Smart Materials and Structures. vol. 12 , nº 6. p. 873-880.
Marc Thomas, Yves Beauchamp. 2003. « Statistical investigation of modal parameters of cutting tools in dry turning ». International Journal of Machine Tools and Manufacture. vol. 43 , nº 11. p. 1093-1106.
Sadok Sassi, Hassan Smaoui, Marc Thomas, Frédéric Laville. 2001. « More details about the interaction of forced and parametric resonances arising from in-plane excitation of imperfect rectangular plates ». Journal of Sound and Vibration. vol. 243 , nº 3. p. 503-524.
Marc Thomas. 2001. « Applications des fluides électro-rhéologiques à l'amortissement des structures ». Communication lors de la conférence : LMA-CNRS ( Marseille, France, mars 2001 )
Marc Thomas. 2001. « Fiabilité, maintenance prédictive et vibration des machines ». Montréal, Canada : École de technologie supérieure. 616 p.
Marc Thomas. 2001. « Prédiction du risque de maux de dos après exposition prolongée à des vibrations aléatoires ». Communication lors de la conférence : LMA-CNRS ( Marseille, France, mai 2001 )
André Moreau, Martin Lord, Daniel Lévesque, Marc Dubois, Jean Bussière, Jean-Pierre Monchalin, Christian Padioleau, Guy Lamouche, Teodor Veres, Martin Viens, Harold Hébert, Pierre Basseras, Cheng-Kuei Jen. 2001. « On-line, non-destructive mechanical property measurement using laser-ultrasound ». «AISI/DOE Advanced Process Control Program Vol. 4 of 6» 10.2172/794988 110 p.
Henri Champliaud. 2000. « Analyse par éléments finis du sertissage de capsules d'étanchéité ». 261 p. Thèse de doctorat. Montréal , École de technologie supérieure
Henri Champliaud, Van Ngan Lê. 2000. « Finite element analysis of crowning sealing caps ». 2000 ANSYS conference proceedings (Pittsburgh, PA, USA, Aug. 28-30, 2000)
F. Lafleur, M. Thomas, F. Laville. 2000. « Modal analysis of structures using acoustical excitation ». Inter-Noise 2000: proceedings (Nice, France, 27-30 aug. 2000) p. 203-206. Paris, France : Société Française d'Acoustique.
F. Lafleur, Marc Thomas, Frédéric Laville. 2000. « Développement d'une méthode d'analyse modale acoustique AMAMISO (Multiple Inputs Single Output) et application de l'excitation acoustique pour le déverminage des circuits électroniques ». Communication lors de la conférence : LMA-CNRS ( Marseilles, France, sept. 2000 )
Mir Saeed Safizadeh, Aouni A. Lakis, Marc Thomas. 2000. « Using short-time Fourier transforms in machinery fault diagnosis ». International Journal of COMADEM. vol. 3 , nº 1. p. 5-16.
Y. Beauchamp, M. Brosseau, M. Thomas. 1999. « A comparative evaluation of seven hand grinder models using psychophysical measurements ». The 26th International Conference on Computers & Industrial Engineering: (the 26th C&IE): December 15-17, 1999, Melbourne, Australia (Melbourne, Australia, Dec. 15-17, 1999) p. 617-621. Industrial Research Institute Swinburne.
Yves Beauchamp, Marc Thomas, Jean Arteau, Denis Marchand. 1999. « Assessment of wood utility pole climbability using psychophysical and mechanical measurements ». International Journal of Occupational Safety and Ergonomics. vol. 5 , nº 1. p. 3-29.
F. Lafleur, M. Thomas, F. Laville. 1999. « Analyse modale expérimentale par excitation acoustique ». CANCAM 99: proceedings: 17th Canadian Congress of Applied Mechanics, held at McMaster University, Hamilton, Ontario, Canada, May 30-June 3, 1999 = CANCAM 99 : comptes rendus: le 17e Congrès Canadien de Mécanique Appliquée, du 30 mai au 3 juin 1999 (Hamilton, ON, Canada, May 30-June 3, 1999) Québec, QC, Canada : CANCAM Central Committee.
M. -S. Safizadeh, A. A. Lakis, M. Thomas. 1999. « Using short time fourier transform in machinery fault diagnosis ». COMADEM '99 : July 1999, 12th International Congress on Condition Monitoring and Diagnostic Engineering Management, University of Sunderland, England (Sunderland, UK, July 6-9, 1999) p. 125-130. Kingham : Coxmoor Publishing.
M. Smail, M. Thomas, A. A. Lakis. 1999. « Utilisation de la modélisation ARMA pour la détection de fissures dans les rotors ». Troisième conférence internationale sur l'automatisation industrielle, École de technologie supérieure, Montréal, 7-9 juin 1999 : actes de la conférence = Third International Conference on Industrial Automation, École de technologie supérieure, Montréal, (Montréal, QC, Canada, 7-9 juin 1999) p. 21.1-21.4. Montréal, QC, Canada : Association internationale de l'automatisation industrielle.
M. Smail, Marc Thomas, A. Lakis. 1999. « ARMA models for modal analysis : effect of model orders and sampling frequency ». Mechanical Systems and Signal Processing. vol. 13 , nº 6. p. 925-941.
M. Smail, Marc Thomas, A. A. Lakis. 1999. « Assessment of optimal ARMA model orders for modal analysis ». Mechanical Systems and Signal Processing. vol. 13 , nº 5. p. 803-819.
M. Thomas. 1999. « A theoretical model for predicting fatigue limits of lumbar spine incurred to random vibration exposure during driving ». The 26th International Conference on Computers & Industrial Engineering: (the 26th C&IE): December 15-17, 1999, Melbourne, Australia (Melbourne, Australia, Dec. 15-17, 1999) p. 419-423. Melbourne, Australia : Industrial Research Institute Swinburne.
M. Thomas. 1999. « Prédiction du nombre de cycles de fatigue avant dommage dans la colonne vertébrale d'un chauffeur soumis à des vibrations aléatoires ». Actes du 21e Congrès de l’Association québécoise pour l’hygiène, la santé et la sécurité du travail / AQHSST (Montréal, QC, Canada, 28-30 avr. 1999) p. 324-333. Montréal, QC, Canada : AQHSST.
Bernard La Mothe, Frédéric Laville, Marc Thomas, Yves Beauchamp. 1998. « Usinage et finition des pièces métalliques : une solution pour réduire le bruit, peu coûteuse et adaptable à d'autres milieux industriels ». Prévention au travail. vol. 11 , nº 3. p. 19-21.
F. Lafleur, M. Thomas, F. Laville. 1998. « Modal analysis of electrical circuits using acoustical sources: methods, results and use ». 4th Annual workshop on accelerated stress testing, AST'98 (Pasadena, CA, USA, Sept. 22-24, 1998) IEEE.
F. Lafleur, Marc Thomas, Frédéric Laville. 1998. « Analyse modale de circuits électroniques à l'aide de sources acoustiques : méthode, résultats et utilisation ». Communication lors de la conférence : 66e Congrès de l'ACFAS ( Québec, QC, Canada, juin 1998 )
F. Lafleur, Marc Thomas, Frédéric Laville. 1998. « Modal analysis of electronic circuits using acoustical sources : methods, results and use ». Communication lors de la conférence : 4th (AST) Accelerated Stress Testing Workshop, IEEE (CPMT) Components, Packaging and Manufacturing Technology Society ( Pasadena, CA, USA, Sept., 1998 )
Frédéric Laville, Marc Thomas, Yves Beauchamp. 1998. « Réduction du bruit occasionné par les opérations d'ébarbage de pièces coulées ». Communication lors de la conférence : Colloque en santé et sécurité du travail (CSST) ( Québec, QC, Canada, oct. 1998 )
Frédéric Laville, Marc Thomas, Yves Beauchamp. 1998. « Réduction du bruit occasionné par les opérations d'ébarbage de pièces d'aluminium coulées ». Communication lors de la conférence : 18e Congrès de l'AQHSST ( Laval, QC, Canada, mai 1998 )
Frédéric Laville, Marc Thomas, Yves Beauchamp. 1998. « Réduction du bruit occasionné par les opérations d'ébarbage de pièces d'aluminium coulées ». «Études et Recherches» IRSST. 33 p.
M. C. Piedboeuf, R. Gauvin, Marc Thomas. 1998. « Damping behaviour of shape memory alloys : strain amplitude, frequency and temperature effects ». Journal of Sound and Vibration. vol. 214 , nº 5. p. 885-901.
Marc Thomas, Yves Beauchamp. 1998. « Development of a new frequency weighting filter for the assessment of grinder exposure to wrist-transmitted vibration ». Computers & Industrial Engineering. vol. 35 , nº 3-4. p. 651-654.
J. Y. Chen, S. V. Hoa, C. K. Jen, M. Viens, J. P. Monchalin. 1998. « Ultrasonic evaluation of graphite/epoxy composites with different curing conditions ». Polymer Composites. vol. 19 , nº 3. p. 225-232.
M. Choquet, D. Lévesque, C. Néron, B. Reid, M. Viens, J.-P. Monchalin, J. P. Komorowski, R. W. Gould. 1998. « Detection of corrosion in aging aircraft structures by laser-ultrasonics ». Nondestructive Characterization of Materials VIII (Boulder, CO, USA, June 15-20, 1997) p. 73-78. Boston, MA : Springer US.
J.-P. Monchalin, C. Néron, M. Choquet, A. Blouin, B. Reid, D. Lévesque, D. Drolet, M. Viens, P. Bouchard, R. Héon, C. Padioleau. 1998. « Laser-ultrasonics inspection and characterization of aeronautic materials ». Alliance of the Americas : the First Pan-American Conference : proceedings of the 1st Pan-American Conference (Toronto, ON, Canada, Sept. 14-18, 1998) Missisauga, Ont. : Canadian Society for Nondestructive Testing Inc..
J.-P. Monchalin, C. Néron, M. Choquet, D. Drolet, M. Viens, P. Bouchard, R. Héon, C. Padioleau. 1998. « Laser-ultrasonics inspection and characterization of aeronautic materials ». 7th European Conference on Non-destructive Testing (ECNDT) (Copenhagen, Denmark, May 26-29, 1998) p. 19-26. ECNDT.
M. Viens, H. Hébert, C. K. Jen. 1998. « Ultrasonic measurement of the remaining thickness of corroded cast iron samples ». III International Workshop--Advances in Signal Processing for NDE of Materials (Québec, QC, Canada, Aug. 05-08, 1997) p. 327-334. Columbus, OH : The American Society for Nondestructive testing.
Y. Beauchamp, M. Thomas, D. Marchand, Jean Arteau. 1997. « An experimental design to assess wood pole climbability using psychophysical and mechanical measurements ». Electricity '97 Conference: new opportunities ahead: Hyatt Regency, Vancouver, April 20-24, 1997: transactions (Vancouver, BC, Canada, Apr. 20-24, 1997) Montreal, QC, Canada : Canadian Electricity Association.
Yves Beauchamp, Denis Marchand, Michel Galopin, Marc Thomas. 1997. « Impact de l'utilisation des pistolets de soudage pourvus d'une buse d'aspiration sur l'activation musculaire des membres supérieurs, la perception psychophysique et la qualité des assemblages soudés ». «Études et Recherches» IRSST. 50 p.
Yves Beauchamp, Marc Thomas, Jean Arteau, Denis Marchand. 1997. « Psychophysical measurements as an effective way of evaluating climbability of wood treated utility poles ». Computers & Industrial Engineering. vol. 33 , nº 3-4. p. 513-516.
Yves Beauchamp, Marc Thomas, Jean Arteau, Denis Marchand. 1997. « Étude sur la "grimpabilité" des poteaux de bois dans le cadre de l'entente conjointe Hydro-Québec et Bell Canada ». Montréal. «Études et Recherches» IRSST. 87 p.
M. Thomas, Y. Beauchamp, Youssef A. Youssef. 1997. « Effect of the lathe boring cutting parameters on surface roughness and tool dynamic forces ». Proceedings: CSME Forum 1996 : Theory of Machines and Mechanisms, and, Advances in Transportation Systems, May 7-9, 1996 (Hamilton, ON, Canada, May 7-9, 1996) p. 521-527. Canadian Society for Mechanical Engineering.
M. Thomas, F. Laville, Y. Beauchamp, Simard F.. 1997. « An experimental design for reducing riveting noise ». 22nd International Conference 1997 on Computers and Industrial Engineering: proceedings of the 22nd ICC & IE, the American University in Cairo Dec. 20-22, 1997 (Cairo, Egypt, Dec. 20-22, 1997) p. 435-438.
M. Thomas, J. Masounave, L. Jacotot. 1997. « Damping and stiffness properties of electrorheological fluids ». ICCE/4: fourth International Conference on Composites Engineering: July 6-12, 1997, Big Island of Hawaii (Big Island, HI, USA, July 6-12, 1997) p. 983-984. International Community for Composites Engineering.
Marc Thomas, Yves Beauchamp. 1997. « Development of a new weighting filter for the assessment of grinder exposure to wrist-transmitted vibration ». 22nd International Conference 1997 on Computers and Industrial Engineering: proceedings of the 22nd ICC & IE, the American University in Cairo Dec. 20-22, 1997 (Cairo, Egypt, Dec. 20-22, 1997) p. 487-490.
Marc Thomas, Yves Beauchamp, A. Y. Youssef, Jacques Masounave. 1997. « An experimental design for surface roughness and built-up edge formation in lathe dry turning ». International Journal of Quality Science. vol. 2 , nº 3. p. 167-180.
H. Wang, B. Cao, C. K. Jen, K. T. Nguyen, M. Viens. 1997. « On-line ultrasonic monitoring of the injection molding process ». Polymer Engineering and Science. vol. 37 , nº 2. p. 363-376.
Yves Beauchamp, Marc Thomas, Jean Arteau. 1996. « Psychophysical measurements as an effective way of evaluating climbability of wood treated utility poles ». Proceedings of the International Conference on Computers & Industrial Engineering (Kyongju, Korea, Oct. 6-9, 1996) p. 925-928. Computers and Industrial Engineering.
Yves Beauchamp, Marc Thomas, Youssef A. Youssef, Jacques Masounave. 1996. « Investigation of cutting parameter effects on surface roughness in lathe boring operation by use of a full factorial design ». Computers & Industrial Engineering. vol. 31 , nº 3-4. p. 645-651.
Sadok Sassi, Marc Thomas, Frédéric Laville. 1996. « Dynamic response obtained by direct numerical integration for pre-deformed rectangular plates subjected to in-plane loading ». Journal of Sound and Vibration. vol. 197 , nº 1. p. 67-83.
M. Thomas, Y. Beauchamp, J. Arteau. 1996. « Mechanical measurements of the hardness of treated wood utility poles for evaluating climbability ». Proceedings of the International Conference on Computers & Industrial Engineering (Kyongju, Korea, Oct. 6-9, 1996) p. 1051-1054. Computers and Industrial Engineering.
Marc Thomas, Yves Beauchamp, Youssef A. Youssef, Jacques Masounave. 1996. « Effect of tool vibrations on surface roughness during lathe dry turning process ». Computers & Industrial Engineering. vol. 31 , nº 3-4. p. 637-644.
Bin Cao, H. Wang, Chen-Kuei Jen, N. T. Nguyen, J. Legoux, Chee Ang Loong, Martin Viens. 1996. « Ultrasonic monitoring of injection molding and die casting ». Nondestructive Evaluation for Process Control in Manufacturing (Scottsdale, AZ, USA, Dec. 03-05, 1996) p. 173-186. SPIE.
J. D. N. Cheeke, Z. Wang, M. Viens. 1996. « Thermal sprayed coatings characterization by acoustic waves ». 1996 IEEE Ultrasonics Symposium : Proceedings (San Antonio, TX, USA, Nov. 03-06, 1996) p. 749-752. IEEE.
J.-Y. Chen, S. V. Hoa, C. K. Jen, M. Viens, J.-P. Monchalin. 1996. « Ultrasonic evaluation of graphite/epoxy composites with different curing conditions ». Composites '96 and Oriented Polymers Symposium : book of proceedings (Boucherville, QC, Canada, 09-11 oct. 1996) p. 249-259. National Research Council Canada, Industrial Materials Institute.
M. Dubois, M. Viens, A. Moreau, C. K. Jen. 1996. « Ultrasonic attenuation measurements at 300 MHz ». First half of the proceedings of the Twenty-Second Symposium on Quantitative Nondestructive Evaluation (Seattle, WA, United states, July 30-Aug. 04,1995) p. 1439-1446. New York : Plenum Press.
Xing Li, Zuoqing Wang, Cheng Kuei Jen, Martin Viens, J. David N. Cheeke. 1996. « Ultrasonic thin-walled tube wave structure for sensing devices ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 43 , nº 2. p. 331-336.
Yuan Liu, Martin Viens, David Cheeke. 1996. « Behavior of extensional modes in a thin rod immersed in a viscous medium ». Journal of the Acoustical Society of America. vol. 99 , nº 2. p. 706-712.
J.-P. Monchalin, C. Néron, G. Vaudreuil, A. Blouin, D. Drolet, M. Dubois, M. Viens, P. Bouchard, M. Choquet, R. Héon, C. Padioleau, J.-D. Aussel. 1996. « Laser-ultrasonics for inspection and characterization of aeronautic materials ». AeroMat '96 (Dayton, OH, USA, June 03-06, 1996)
M. Viens, D. Drolet, A. Blouin, J.-P. Monchalin, C. Moreau. 1996. « Nondestructive characterization of plasma sprayed coatings by laser ultrasonics ». Thermal spray 1996: Practical solutions for engineering problems, proceedings of the 9th National thermal spray conference (Cincinnati, OH, USA, Oct. 07-11, 1996) p. 947-951. ASM International.
Martin Viens, Daniel Lévesque, Chen-Kuei Jen, Harold Hébert. 1996. « In-situ ultrasonic thickness measurement of underground water mains ». Nondestructive Evaluation of Utilities and Pipelines (Scottsdale, AZ, USA, Dec. 03-05, 1996) p. 157-164. SPIE.
Martin Viens, Paul C. H. Li, Zuoqing Wang, Cheng Kuei Jen, Michael Thompson, J. David N. Cheeke. 1996. « Mass sensitivity of thin rod acoustic wave sensors ». IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control. vol. 43 , nº 5. p. 852-857.
Yves Beauchamp, Marc Thomas, Youssef A. Youssef, Jacques Masounave. 1995. « Investigation of cutting parameter effects on surface roughness in lathe boring operation by use of a full factorial design ». Proceedings of 18th International Conference on Computers & Industrial Engineering : ICC&IE '95, Shanghai, China, October 25-27, 1995 (Shanghai, China, Oct. 25-27, 1995) p. 534-540. China Machine Press.
Jean-Pierre Gagné, Marc Thomas, David Bensoussan. 1995. « Contrôle actif des vibrations par filtre passe bas et retour d'états sur une structure flexible ». Canadian Conference on Electrical and Computer Engineering, 1995 (Montréal, QC, Canada, 5-8 sept. 1995) p. 181-186. IEEE.
M. Thomas, Y. Beauchamp, A. Y. Youssef, J. Masounave. 1995. « Effect of tool vibrations on surface roughness during lathe dry turning process ». Proceedings of the 18th International Conference on Computers and Industrial Engineering (Shanghai, China, Oct. 25-27, 1995) p. 526-533. Beijing, China : China Machine Press.
M. Thomas, J. Masounave, T. M. Dao, C. T. Le Dinh, F. Lafleur. 1995. « Rolling element bearing degradation and vibration signature relationship ». Acoustical and vibratory surveillance methods and diagnostic techniques: 2nd international symposium = Méthodes de surveillance et techniques de diagnostic acoustiques et vibratoires (Paris, France, Oct. 10-12, 1995) p. 267-277. Société Française des Mécaniciens.
Marc Thomas, H. Nguyen, L. Hamidi, M. Massoud, J. B. Piaud. 1995. « Détection de fissures de rotors par analyse modale expérimentale ». Transactions of the Canadian Society for Mechanical Engineering. vol. 19 , nº 2. p. 155-174.
X. Li, J. D. N. Cheeke, Z. Wang, C. K. Jen, M. Viens, G. Yi, M. Sayer. 1995. « Ultrasonic thin-walled tube wave devices for sensor applications ». Applied Physics Letters. vol. 67 , nº 1. p. 37-39.
Yves Beauchamp, Marc Thomas, Jacques Masounave, Youssef A. Youssef. 1994. « Application of a full factorial design for the development of prediction models for surface roughness in lathe turning and boring operations ». Tenth International Conference of the Israel Society for Quality (Jerusalem, Israel, Nov. 14-17, 1994) p. 953-961. Jerusalem, Israel : ISAS International Seminars.
Yves Beauchamp, Marc Thomas, Jacques Masounave, Youssef A. Youssef. 1994. « Développement d'un modèle empirique de prédiction du fini de surface et pièces tournées par chariotage ». Communication lors de la conférence : 62e Congrès de l'ACFAS ( Montréal, QC, Canada, 16-20 mai 1994 )
J.P. Gagné, Marc Thomas, David Bensoussan, C. Sauvageau. 1994. « Atténuation de vibrations d'une structure flexible ». Communication lors de la conférence : 62e Congrès de l'ACFAS ( Montréal, QC, Canada, 16-20 mai 1994 )
H. Nguyen, Marc Thomas. 1994. « Détection de fissures d'arbre tournant par analyse modale expérimentale ». Communication lors de la conférence : 62e Congrès de l'ACFAS ( Montréal, QC, Canada, 16-20 mai 1994 )
M. Thomas, F. Laville, Y. Beauchamp, Y. Goudreault. 1994. « Les riveteuses pneumatiques ». Santé Sécurité +. vol. 11 , nº 3. p. 8.
Marc Thomas. 1994. « Contrôle actif et adaptatif des vibrations et des paramètres de coupe pour améliorer le fini de surface lors du tournage de pièces ». Communication lors de la conférence : CITEC Aerospace Technology Transfer Forum ( Longueuil, QC, Canada, June, 1994 )
Marc Thomas, Yves Beauchamp, Youssef A. Youssef, Jacques Masounave. 1994. « Influence des vibrations sur le fini de surface de pièces tournées par chariotage ». Communication lors de la conférence : 62e Congrès de l'ACFAS ( Montréal, QC, Canada, 16-20 mai 1994 )
Youssef A. Youssef, Yves Beauchamp, Marc Thomas. 1994. « Comparison of a full factorial experiment to fractional and taguchi designs in a lathe dry turning operation ». Computers & Industrial Engineering. vol. 27 , nº 1-4. p. 59-62.
Youssef A. Youssef, Yves Beauchamp, Marc Thomas. 1994. « Comparison of a full factorial experiment to fractional and taguchi designs in a lathe dry turning operation ». Proceedings of 16th International Conference on Computers & Industrial Engineering ICC&IE-94 (Ashikaga, Japan, Mar. 7-9, 1994) p. 286-289. Ashikaga, Japan : Ashikaga Institute of Technologie.
X. Li, Z. Wang, C. K. Jen, M. Viens, J. D. N. Cheeke, G. Yi, M. Sayer. 1994. « Ultrasonic thin wall tube wave sensors ». 1994 Proceedings of IEEE Ultrasonics Symposium (Cannes, France, Oct. 31-Nov. 03, 1994) p. 623-628. IEEE.
M. Viens, Y. Tsukahara, C. K. Jen, J. D. N. Cheeke. 1994. « Leaky torsional acoustic modes in infinite clad rods ». Journal of the Acoustical Society of America. vol. 95 , nº 2. p. 701-707.
Yves Beauchamp, Marc Thomas. 1993. « Bilan des études expérimentales sur la performance humaine dans les systèmes robotisés ». Communication lors de la conférence : Robotique et Ergonomie ( Genève, Suisse, sept. 1993 )
Yves Beauchamp, Marc Thomas, T. Stobbe. 1993. « Some ergonomic design criteria for man-robot systems based on experimental studies ». CAD/CAM, robotics, and autonomous factories : proceedings of INCARF-93, Indian Institute of Technology, New Delhi, India, December 16-19, 1993 (New Delhi, India, Dec. 16-19, 1993) p. 703-714. New York, USA : Tata McGraw Hill.
Marc Thomas. 1993. « La transmission des vibrations au corps humain lors de la conduite de véhicules : rétrospective et futur ». Communication lors de la conférence : 61e Congrès de l'ACFAS ( Rimouski, QC, Canada, 17-21 mai 1993 )
Marc Thomas. 1993. « Le rôle de l'ingénieur en dynamique des structures ». Communication lors de la conférence : Conférence ISA ( Montréal, QC, Canada, mars 1993 )
Marc Thomas, Yves Beauchamp. 1993. « Expériences d'intervention sur les vibrations transmises au corps entier lors de la conduite de véhicules ». Compte rendu du 3e colloque, Association des médecins du réseau public en santé au travail du Québec (Montréal, QC, Canada, Oct. 1993) p. 192-203.
Marc Thomas, Yves Beauchamp, B. L. Juneja, K. K. Pujara, R. Sager. 1993. « Prediction of surface roughness for turning using only controlled cutting parameters ». CAD/CAM, robotics, and autonomous factories : proceedings of INCARF-93, Indian Institute of Technology, New Delhi, India, December 16-19, 1993 (New Delhi, India, 16-19 déc. 1993) p. 517-526. New Delhi, India : Tata McGraw-Hill.
Y. Liu, M. Viens, J. D. N. Cheeke, C. K. Jen. 1993. « Anomalous magnetoelastic waves in nickel wire ». Journal of Applied Physics. vol. 73 , nº 5. p. 2584-2586.
M. Viens, P. C. H. Li, Z. Wang, C. K. Jen, M. Thompson, J. D. N. Cheeke. 1993. « Gravimetric response of thin rod acoustic wave sensors ». 1993 Proceedings IEEE Ultrasonics Symposium (Baltimore, MD, USA, Oct. 31-Nov. 03, 1993) p. 359-364. IEEE.
Martin Viens. 1993. « Conception et caractérisation de capteurs acoustiques ». Thèse de doctorat. Sherbrooke , Université de Sherbrooke
Marc Thomas, C. T. Le Dinh, C. T. Huyng. 1992. « Mesure de charge de camions par réseaux neuronaux et identification modale ». Proceedings CSME Forum : transport 1992, 1 June - 4 June = Comptes rendus Forum SCGM : transport 1992, 1 Juin - 4 Juin (Montréal, QC, Canada, 1-4 juin 1992) p. 928-933. Montréal, QC, Canada : Concordia University.
M. Viens, Y. Liu, Z. Wang, C. K. Jen, J. D. N. Cheeke. 1992. « Investigations of extensional and torsional acoustic wave thin rod sensors ». First half of the proceedings of the Eighteenth Annual Review of Progress in Quantitative Nondestructive Evaluation (Brunswick, ME, USA, July 28-Aug. 02, 1991) p. 1059-1065. New York : Springer Science+Business Media.
C. K. Jen, J. C. H. Yu, Z. Wang, M. Viens, J. D. N. Cheeke, J. D. Dai. 1991. « Thin rod flexural acoustic wave devices: A sensor candidate ». Second half of the proceedings of the Seventeenth Annual Review of Progress in Quantitative Nondestructive Evaluation (La Jolla, California, July 15-20,1990) p. 2157-2163. New York : Plenum Press.
Yuan Liu, M. Viens, J. D. N. Cheeke, C. K. Jen. 1991. « Anomalous magnetoelastic waves in nickel wire ». IEEE Ultrasonics Symposium (Orlando, FL, USA, Dec. 08-11, 1991) p. 1075-1078. IEEE.
Zuoqing Wang, Martin Viens, Cheng-Kuei Jen, David Cheeke, Yuan Liu. 1991. « Analysis of thin rod acoustic wave gravimetric sensors ». Sensors and Materials. vol. 3 , nº 3. p. 159-172.
Martin Viens, J. David N. Cheeke. 1990. « Highly sensitive temperature sensor using SAW resonator oscillator ». Sensors and Actuators: A. Physical. vol. 24 , nº 3. p. 209-211.
Z. Wang, M. Viens, C. K. Jen, J. D. N. Cheeke, Y. Liu. 1990. « Analysis of thin rod acoustic wave gravimetric sensors ». IEEE Symposium on Ultrasonics (Honolulu, HI, USA, Dec. 04-07, 1990) p. 345-349. IEEE.
J. L. Fihey, P. Cielo, G. Begin. 1984. « On line weld penetration measurement using an infrared sensor ». In Welding in Energy-Related Projects . p. 177-188. Pergamon Press Inc.
J. L. Fihey, R. Simoneau. 1984. « Weld pool geometry variation in GTA welding of austenitic stainless steel ». In Welding in Energy-Related Projects . p. 259-268. Pergamon Press Inc.