M. Kedadouche, Z. Liu, V.-H. Vu, 2016, “A new approach based on OMA-empirical wavelet transforms for bearing fault diagnosis”, Measurement, 90, 292-308. Abed A., Bouzidane A., Thomas M. and Zahloul H., December 2016, Performance characteristics of a three-pad hydrostatic squeeze film damper compensated with new electrorheological valve restrictors. Journal of Engineering Tribology (vols 208-210) 1994-1996
M. Kedadouche, M. Thomas, A. Tahan, 15 juin 2016. A comparative study between Empirical Wavelet Transforms and Empirical Mode Decomposition methods: application to bearing defect diagnosis. Mechanical Systems and Signal Processing. (81), 88-107. 2015 Guilbault R., Lalonde S. and Thomas M., 2015, Modeling and monitoring tooth fillet crack growth in dynamic simulation of spur gear set, Journal of Sound and Vibration. vol. 343. pp. 144-165. Najjari M., Guilbault R., 2015, Formula derived from particle swarm optimizations (PSO) for optimum design of cylindrical roller profile under EHL regime. Mechanism and Machine Theory, 71, pp.50–61 M.Kedadouche, M.Thomas, A. Tahan, and R. Guilbault, Nonlinear Parameters for Monitoring Gear: Comparison Between Lempel-Ziv, Approximate Entropy, and Sample Entropy Complexity. Shock and Vibration Volume 2015 (2015), ID 959380,12 pages. M. Kedadouche, M. Thomas and A. Tahan. Sept. 2015. A hybrid method combining Teager Kaiser energy operator, empirical mode decomposition and minimum entropy deconvolution for monitoring gears damages. Mechanics & Industry, 16 6 (2015) 610.
Imaouchen Y., Alkama R., Thomas M. July 2015. Complexity based on synchro-squeezing analysis in gear diagnosis. Mechanics & Industry, 16 (5), 8 p. 2014
Najjari M., Guilbault R., 2014, Edge contact effect on thermal elastohydrodynamic lubrication of finite contact, Tribology International, 71, pp.50–61.
Najjari M., Guilbault R., 2014, Modeling the edge contact effect of finite contact lines on subsurface stresses. Tribology International. 77: 78-85.
M. Kedadouche, M. Thomas and A. Tahan. July 2014. Cyclostationarity applied to acoustic emission and development of a new indicator for monitoring bearing defects. Mechanics & Industry, 15 (6), 467 – 476.
T. Kidar, M. Thomas, M. El Badaoui, R. Guilbault. July 2014, Control of phases by Esprit and WLSE methods for the early detection of gear cracks. Mechanics & Industry, 15 (6), 487 – 495.
M. Kedadouche, M. Thomas and A. Tahan, 21 april 2014. Monitoring bearing defects by using a method combining EMD, MED and TKEO. Advances in Acoustics and Vibration. Hindawi, Vol 2014, ID 502080,10 p.
Vu V.H., Liu Z., Thomas M., Li W. and Hazel B., March 2016. Output-only identification of mode shape coupling in a flexible robot by vector autoregressive modeling. Mechanism and Machine Theory, 97, 141-154.
Vu V.-H., Badri B., Thomas M. and Jean P, 2016. Vibration analysis and diagnosis on a pump in operation. Mechanics & Industry, 17 (101), 10 p.
2013 V. Lê, H. Champliaud, 2013 “Safety Factor of Beam-Column Structures Based on Finite Element Linear Buckling Analysis”, CFM-2013 Congrès Français de Mécanique, 26-30 août 2013, Talence-Bordeaux, France 2012 V. Lê, H. Champliaud, 2012 , “Finite Element Simulations for Comparing Three Manhole Designs for Horizontal Mills”, International Association of Science and Technology Development, IASTED-MS 2012,July 3-5, 2012, Banff, Calgary, Canada Champliaud H., N. Lê, "Beginning Learning Principles of Finite Element Method with Heat Conduction", 5th World Universities Forum, 8-10 Jan 2012, Rhodes, Grèce. Najjari M., Guilbault R., 2012, Edge Correction in the Elastohydrodynamic Lubrication of Finite Line Contact. Proceedings of the International Conference on Mechanical Engineering and Mechatronics Ottawa, Ontario, Canada, 15-17 Aug. Lê N., H. Champliaud, "A Teaching Approach for Enhancing Structural Design Aspects in Basic Engineering Courses", 5th World Universities Forum, 8-10 Jan 2012, Rhodes, Grèce. 2011 N. Lê, H. Champliaud, "Finite Element Analysis of Spring Back Strain Energy of Metal Sheet Coils", NAFEMS World Congress, 23-26 Mai 2011, Boston, États-Unis. Saboori M., Gholipour J., Champliaud H., Gakwaya A., Savoie J., Wanjara P. (2011). Prediction of Burst Pressure Using a Decoupled Ductile Fracture Criterion for Tube Hydroforming of Aerospace Alloys, ESAFORM 2011, Belfast, Ireland, April 27-29. 2010 Guilbault, R., 2010, “A Fast Correction for Traction-Free Surface of Elastic Quarter-Space,” Third International Conference on Tribology and Design, M.Hadfield , J. Seabra and C.A. Brebia, eds., WIT Press, Southampton, UK, pp. 37–48. 2009 Champliaud H., Feng, Z., Bersee H. (2009), Three-Point Bending Testing of Sandwich Beams and Finite Element Comparison, 2009 ASME Int. Mech. Eng. Conf., Lake Buena Vista, Floride, É.-U., 13-19 novembre. Ayari H., Thomas M., Doré S., Taiar R. and Dron J.P. , Mai 2009. Predicting the adverse health effects to long term whole-body vibration exposure, CIRI, paper CIRI002, Reims, 19 pages. 2007 Duchaine F., Bersee H.E.N., Champliaud H. (2007). The Influence of the Thickness on 3D Elastic Material Properties of Unidirectional E-glass/epoxy Laminated Composites, Cancom 2007, Winnipeg, Canada, August 14-17. Feng Z., Champliaud H., Zeng J., Dao T.-M. (2007). Investigation of Influence of Sliding of Rolls Over Plate on Continuous Bending with Noncompatible Conical Rolls, The 18th IASTED International Conference on Modelling and Simulation, MS 2007, Montreal, Canada, May 30 to June 1. Feng Z., Champliaud H., Dao T.-M. (2007). Modeling and Simulation of Conical Bending with Cylindrical Rolls, 2007 ASME Pressure Vessels and Piping Division Conference, San Antonio, Texas, U.S.A., July 22-26. Charette O., Champliaud H., Thomas M. (2007). FEM Calculation of Frequencies Variation Caused by Residual Stress Distribution in Welded Structures, The 18th IASTED International Conference on Modelling and Simulation, MS 2007, Montreal, Canada, May 30 to June 1. Feng Z., Champliaud H., Zeng J., Dao T.-M. (2007). Investigation of Influence of Sliding of Rolls Over Plate on Continuous Bending with Noncompatible Conical Rolls, The 18th IASTED Ayari H., Thomas M. and Doré S., December 2007. Development of an injury risk factor for drivers Proc. 1st int. Conf. on Industrial Risk Engineering CIRI, Montreal, ISBN 978-2-921145-65-7, 137-150. Ayari H., Thomas M. and Doré S., October 2007. A design of experiment for studying the effect of human body parameters on an injury risk of drivers exposed to vibration, Proc. of the 37th International conf. on Computers and Industrial Engineering, CIE 07, Alexandria, Egypt, pp. 620-628. Sun Y., Thomas M., and Masounave J., July 2007, Experimental investigation on Electrorheological fluid rheology and dielectric properties, Int. Conf. on Smart Materials and Nanotechnology in Engineering (SMN2007), Vol 6423-34, Shanyi Du, Jinsong Leng and Anand K. Asundi editors Harbin China, 8p. 2006 Duchaine F., Baten E.M., Champliaud H., Bersee H.E.N. (2006). Comparison of Beam Theories with FEA in Three-Point Bending of Thick Composites, 8th International Conference on Computational Structures Technology, Las Palmas de Gran Canaria, Spain, September 12-15. Rhéaume F.-É., Champliaud H., Liu Z. (2006). Simulating Strain Wave Gearing Torsional Stiffness using the Finite Element Method, 2006 Ansys Conference and Exhibition, Pittsburgh, USA, May 2-4. 2005 Thomas M., Champliaud H. (2005). Effect of Residual Stresses on Modal Parameters of Welded Structures, 23rd CMVA Seminar, Canadian Machinery Vibration Ass., Edmonton, Alberta, October 26-28. Texte Complet Champliaud H., Bouzid A. (2005). Computation of Unloading Stiffness of Nonlinear Gaskets Using Dual Kriging Interpolation, 7th MESO 2005 Int. Conf. on Mesomechanics, Montréal, Canada, August 1-4.
2017 Mirakhorli F., Cao X., Pham X-T., Wanjara P. and Fihey J-L. (2017). “Technical Challenges in Narrow-Gap Root Pass Welding during Tandem and Hybrid Laser-Arc Welding of a Thick Martensitic Stainless Steel”, Materials Science Forum, 879, 1305-1310 Mirakhorli F., Cao X., Pham X-T., Wanjara P. and Fihey J-L. (2017). “Phase Structures and Morphologies of Tempered CA6NM Stainless Steel Welded by Hybrid Laser-Arc Process”, Mater. Charact., 123, 264-274. 2016 Texier D., Zedan Y., Amoros T., Feulvarch E., Stinville J.C., Bocher P. 2016 Near-surface mechanical heterogeneities in a dissimilar aluminum alloys friction stir welded joint. Materials & Design 108, pp. 217-229 Giraud L., Robe H., Claudin C., Desrayaud C., Bocher P., Feulvarch E. 2016 Investigation into the dissimilar friction stir welding of AA7020-T651 and AA6060-T6. Journal of Materials Processing Technology 235, pp. 220-230 Jomaa W., Songmene V., Bocher P. 2016 An Investigation of Machining-Induced Residual Stresses and Microstructure of Induction-Hardened AISI 4340 Steel. Materials and Manufacturing Processes 31 (7), pp. 838-844 Pourian M.H., Bridier F., Pilvin P., Bocher P. 2016 Prediction of crack initiation sites in alpha Ti- alloys microstructures under dwell-fatigue using Cellular Automaton simulation method International. Journal of Fatigue 85, pp. 85-97 Savaria V., Bridier F., Bocher P. 2016 Predicting the effects of material properties gradient and residual stresses on the bending fatigue strength of induction hardened aeronautical gears. International Journal of Fatigue 85, pp. 70-84 Anderson M., Bridier F., Gholipour J., Jahazi M., Wanjara P., Bocher P. 2016 Mechanical and Metallurgical Evolution of Stainless Steel 321 in a Multi-step Forming Process. Journal of Materials Engineering and Performance 25 (4), pp. 1526-1538 Jomaa W., Songmene V., Bocher P. 2016 An Hybrid Approach Based on Machining and Dynamic Tests Data for the Identification of Material Constitutive Equations. Journal of Materials Engineering and Performance 25 (3), pp. 1010-1027 Vanderesse N., Ky I., González F.Q., Nuño N., Bocher P. 2016 Image analysis characterization of periodic porous materials produced by additive manufacturing. Materials & Design 92, pp. 767-778 Amrei M.M., Monajati H., Thibault D., Verreman Y., Bocher P. 2016 Effects of Various Post- Weld Heat Treatments on Austenite and Carbide Formation in a 13Cr4Ni Steel Multipass Weld. Metallography, Microstructure, and Analysis 5 (1), pp. 50-61 Stinville J.C., Echlin M.P., Texier D., Bridier F., Bocher P., Pollock T.M. 2016 Sub-grain scale digital image correlation by electron microscopy for polycrystalline materials during elastic and plastic deformation. Experimental Mechanics 56 (2), pp. 197-216 Amrei M.M., Monajati H., Thibault D., Verreman Y., Germain L., Bocher P. 2016 Microstructure characterization and hardness distribution of 13Cr4Ni multipass weld metal. Materials Characterization 111, pp. 128-136 Aghasibeig M., Monajatizadeh H., Bocher P., Dolatabadi A, Wuthrich R. 2016 Cold spray as a novel method for development of nickel electrode coatings for hydrogen production. International Journal of Hydrogen Energy 41 (1), pp. 227-238 Touazine H., Jahazi M., Bocher P. 2016 Accurate determination of damaged subsurface layers in machined Inconel 718. The International Journal of Advanced Manufacturing Technology, 1-9,2016 (Available online) Luk-Cyr J., El-Bawab Rayan, Lanteigne J., Champliaud H., Vadean A. (2016). Mechanical properties of 75% Ar / 25% CO2 flux-cored arc welded E309L austenitic stainless steel, Materials Science & Engineering A, http://dx.doi.org /10.1016/j.msea.2016.09.099)
Luk-Cyr J., El-Bawab Rayan, Champliaud H., Lanteigne J., Vadean A. (2016). Sequential approximate optimization of industrial hammer peening using finite element simulations, Structural and Multidisciplinary Optimization, DOI: 10.1007/s00158-016-1538-7. Sarafan S., Wanjara P., Gholipour J., Champliaud H. (2016). Global and Local Characteristics of an Autogenous Single Pass Electron Beam Weld in Thick Gage UNS S41500 Steel, Material Science & Engineering A, Volume 666, pp 360-371 Saboori M., Gholipour J., Champliaud H., Gakwaya A., Wanjara P., Savoie J. (2016). Prediction of burst pressure in multi stage tube hydroforming of aerospace alloys, Journal of Engineering for Gas Turbines and Power, August 2016, Volume 138, 082101-1-5 Gendron M., Boudreault E., Hazel B., Tan P., Champliaud H. (2016). Non-linear optimization of a new robotic induction process for local heat treatment using thermal finite element analysis, International Journal of Advanced Manufacturing Technology, May 2016, Volume 84, Issue 5, pp 1013-1029 (CRSNG).
Salem J., Champliaud H., Feng Z., Dao T. M. (2016). Experimental analysis of an asymmetrical three-roll bending process, International Journal of Advanced Manufacturing Technology, April 2016, Volume 83, Issue 9, pp1823-1833.